Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY (w/ Glow Plug Controller)

ENGINE ASSEMBLY (w/ Glow Plug Controller) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



4. REMOVE NO. 1 ENGINE UNDER COVER


5. REMOVE NO. 2 ENGINE UNDER COVER


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



8. DRAIN TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



9. DRAIN POWER STEERING FLUID


10. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.



11. REMOVE BATTERY


12. REMOVE BATTERY TRAY


13. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
(Click here)


15. REMOVE RADIATOR ASSEMBLY
(Click here)


16. REMOVE STARTER ASSEMBLY
  1. for 2.2 kW Type Denso Made: (Click here)
  2. for 2.2 kW Type Bosch Made: (Click here)


17. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


18. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


    C098708E10
  1. Place matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 4 nuts, 4 bolts and 4 washers and disconnect the propeller shaft.



    C098709E09
  1. Place matchmarks on the propeller shaft flange and transfer flange.
    Text in Illustration 
    *1
    Matchmark

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



19. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


20. DISCONNECT HEATER HOSE


    A236415
  1. Disconnect the 2 heater hoses.



21. DISCONNECT PRESSURE FEED TUBE ASSEMBLY


    A236416
  1. Disconnect the oil reservoir to pump hose.



    A236417
  1. Disconnect the pressure feed tube.



22. DISCONNECT FUEL HOSE


    A236418
  1. Disconnect the 2 fuel hoses.



23. DISCONNECT UNION TO CONNECTOR TUBE HOSE


    A236419
  1. Disconnect the union to connector tube hose.



24. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
    Text in Illustration 
    *1
    Stopper



    B278059E01
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge



25. DISCONNECT WIRE HARNESS


A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A233020
  1. Remove the 2 nuts, detach the clamp and disconnect the wire harness.

  1. Disconnect the 4 glow plug controller connectors.

  1. Disconnect the 4 injector driver connectors.



    A272479
  1. Disconnect the 3 TCM connectors.

  1. Disconnect the 6 ECM connectors.



26. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



27. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


28. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(Click here)


29. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator.



30. REMOVE PUMP IMPELLER DRIVE PLATE


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114804
  1. Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate, and flywheel.



31. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.



32. INSTALL ENGINE HANGERS


    A224109E01
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030

    NOTICE:
    Install the engine hangers with new bolts.



33. REMOVE ENGINE ASSEMBLY
  1. Attach an engine sling device and hang the engine with a chain block.



    A098988E01
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



34. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

  1. Remove the 2 bolts and 2 engine hangers.



35. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.



36. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A233592E02
  1. Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *A
    RH Side
    *B
    LH Side



37. REMOVE NO. 1 TIMING BELT COVER


    A015094E01
  1. Remove the 6 bolts, 6 washers and timing belt cover.



38. REMOVE TIMING BELT


    A070549E05
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.



    A070550E01
  1. Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.



  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.



39. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.



40. REMOVE CRANKSHAFT PULLEY


    A251844E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A251845E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



41. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.



42. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 1 intercooler support bracket.



43. REMOVE NO. 2 IDLE PULLEY ASSEMBLY
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.



44. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



45. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



46. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



47. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



48. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)


49. REMOVE EXHAUST MANIFOLD


    A152664
  1. Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.

  1. Remove the gasket.



50. REMOVE WATER INLET


A250419
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and water inlet.

  1. Remove the bolt and wire harness clamp bracket from the water inlet.



51. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.



52. REMOVE WATER OUTLET


    A233596
  1. Remove the 2 bolts, water outlet and gasket.



53. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A253491
  1. Disconnect the 2 connectors.

  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



54. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
(Click here)


55. REMOVE INTAKE MANIFOLD
(Click here)


56. REMOVE GLOW PLUG ASSEMBLY
(Click here)


57. REMOVE WIRING HARNESS CLAMP BRACKET


    A271761
  1. Detach the 6 wire harness clamps.

  1. Remove the 3 bolts and 2 wiring harness clamp brackets.



58. REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY


    A252282
  1. Remove the 3 bolts and No. 2 cylinder head cover.



59. REMOVE OIL FILTER SUB-ASSEMBLY


    A227248E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



60. REMOVE COMMON RAIL ASSEMBLY
(Click here)


61. REMOVE FUEL SUPPLY PUMP ASSEMBLY
(Click here)


62. REMOVE OIL COOLER COVER SUB-ASSEMBLY
  1. Disconnect the oil pressure switch connector and wire harness.



    A038741E01
  1. Remove the 13 bolts, 2 nuts and oil cooler cover.



63. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



64. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



65. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.



  1. Detach the 3 clips, and the bolt and crankshaft position sensor.


    A253484



66. REMOVE CAMSHAFT POSITION SENSOR


A112046
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.



67. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A252686
  1. Disconnect the engine coolant temperature sensor connector.

  1. Remove the engine coolant temperature sensor.

  1. Remove the gasket from the engine coolant temperature sensor.



68. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A233593E03
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.
    Text in Illustration 
    *a
    RH Side
    *b
    LH Side



69. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.