Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2016.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen.
·

Brake actuator assembly (skid control ECU)*1

·

Master cylinder solenoid (skid control ECU)*2

·

Four wheel drive control ECU

·

Certification ECU (smart key ECU assembly)

·

Power management control ECU

·

Power steering ECU assembly

·

Navigation receiver assembly*3

·

Radio and display receiver assembly*4

·

Spiral cable sub-assembly (steering angle sensor)

·

Yaw rate sensor assembly

·

Center airbag sensor assembly

·

Main body ECU (multiplex network body ECU)



*1: for 2TR-FE

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV

*3: w/ Navigation System (for Navigation Receiver Type)

*4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System


WIRING DIAGRAM

C334437E02
0.765,3.607 1.175,3.749 0.410,0.141 10 CANH 0.782,4.06 1.175,4.203 0.393,0.143 10 CANL 1.304,3.52 1.715,3.661 0.410,0.141 10 19 1.322,3.973 1.715,4.116 0.393,0.143 10 20 0.226,4.447 1.439,4.837 1.213,0.391 10 G53 0.226,4.615 2.181,4.969 1.955,0.354 10 Four Wheel Drive Control ECU 0.779,0.627 1.189,0.769 0.410,0.141 10 CANH 0.796,1.08 1.189,1.223 0.393,0.143 10 CANL 1.318,0.54 1.729,0.681 0.410,0.141 10 25 1.336,0.993 1.729,1.136 0.393,0.143 10 14 0.303,1.467 1.516,1.857 1.213,0.391 10 A6 0.303,1.635 1.897,1.989 1.594,0.354 10 Brake Actuator Assembly (Skid Control ECU)*4 0.779,5.363 1.189,5.504 0.410,0.141 10 CA1H 0.796,5.816 1.189,5.959 0.393,0.143 10 CA1L 1.304,5.275 1.715,5.417 0.410,0.141 10 14 1.322,5.728 1.715,5.871 0.393,0.143 10 13 0.282,6.202 1.495,6.593 1.213,0.391 10 G51 0.282,6.37 1.922,6.725 1.640,0.354 10 Power Management Control ECU 5.977,5.363 6.387,5.504 0.411,0.141 10 CANH 5.977,5.816 6.370,5.959 0.393,0.143 10 CANL 5.773,5.275 6.184,5.416 0.411,0.141 10 9 5.693,5.728 6.086,5.871 0.393,0.143 10 10 5.487,6.174 6.659,6.565 1.172,0.391 10 G38 5.487,6.342 7.072,6.697 1.585,0.354 10 Certification ECU (Smart Key ECU Assembly) 5.977,7.214 6.387,7.355 0.411,0.141 10 CANH 5.977,7.667 6.370,7.810 0.393,0.143 10 CANL 5.752,7.126 6.163,7.267 0.411,0.141 10 1 5.752,7.579 6.146,7.722 0.393,0.143 10 2 3.336,7.126 3.746,7.267 0.411,0.141 10 5 3.353,7.579 3.746,7.722 0.393,0.143 10 16 3.336,5.275 3.746,5.416 0.411,0.141 10 3 3.353,5.728 3.746,5.871 0.393,0.143 10 14 3.336,3.52 3.746,3.661 0.411,0.141 10 6 3.353,3.973 3.746,4.116 0.393,0.143 10 17 2.495,3.52 2.906,3.661 0.411,0.141 10 2 2.421,3.973 2.815,4.116 0.393,0.143 10 13 2.495,5.275 2.906,5.416 0.411,0.141 10 4 2.421,5.728 2.815,5.871 0.393,0.143 10 15 2.495,7.126 2.906,7.267 0.411,0.141 10 1 2.421,7.579 2.815,7.722 0.393,0.143 10 12 5.683,8.053 6.855,8.444 1.172,0.391 10 G46 5.683,8.207 6.983,8.512 1.300,0.305 10 Power Steering ECU Assembly 3.313,0.996 3.705,1.313 0.392,0.317 10 *4 3.313,0.52 3.705,0.837 0.392,0.317 10 *4 3.313,2.341 3.705,2.658 0.392,0.317 10 *4 3.313,1.865 3.705,2.182 0.392,0.317 10 *4 2.922,1.876 3.333,2.017 0.411,0.141 10 9 2.94,2.329 3.333,2.472 0.393,0.143 10 20 2.908,0.54 3.319,0.681 0.411,0.141 10 10 2.926,0.993 3.319,1.136 0.393,0.143 10 21 2.019,0.54 2.429,0.681 0.411,0.141 10 11 2.036,0.993 2.429,1.136 0.393,0.143 10 22 1.817,2.765 3.030,3.156 1.213,0.391 10 A72 1.817,2.934 3.794,3.178 1.977,0.244 10 No. 4 Junction Connector*4 2.256,8.09 3.469,8.480 1.213,0.391 10 G97 2.256,8.258 3.871,8.502 1.616,0.244 10 No. 1 Junction Connector 1.679,0.996 2.071,1.313 0.392,0.317 10 *4 1.679,0.52 2.071,0.837 0.392,0.317 10 *4 3.612,1.603 4.004,1.920 0.392,0.317 10 *6 4.126,1.603 4.518,1.920 0.392,0.317 10 *6 6.244,0.53 6.711,0.671 0.466,0.141 10 CANH 6.244,1.176 6.711,1.352 0.466,0.176 10 CANL 6.384,1.492 6.836,1.684 0.453,0.192 10 ECM 5.037,0.625 5.327,0.768 0.290,0.143 10 G58 5.037,1.078 5.327,1.221 0.290,0.143 10 G58 4.595,0.625 4.965,0.768 0.370,0.143 10 G181 4.595,1.078 4.965,1.221 0.370,0.143 10 G181 4.627,0.437 4.933,0.579 0.306,0.141 10 13*4 4.626,0.888 4.934,1.031 0.309,0.143 10 14*4 4.198,0.625 4.568,0.768 0.370,0.143 10 G184 4.198,1.078 4.568,1.221 0.370,0.143 10 G184 4.23,0.437 4.536,0.579 0.306,0.141 10 17*5 4.229,0.888 4.537,1.031 0.309,0.143 10 28*5 5.039,0.437 5.345,0.579 0.306,0.141 10 35*3 5.038,0.888 5.346,1.031 0.309,0.143 10 36*3 5.444,0.625 5.734,0.768 0.290,0.143 10 G56 5.444,1.078 5.734,1.221 0.290,0.143 10 G56 5.449,0.437 5.755,0.579 0.306,0.141 10 31*2 5.448,0.888 5.756,1.031 0.309,0.143 10 25*2 5.843,0.625 6.133,0.768 0.290,0.143 10 G56 5.843,1.078 6.133,1.221 0.290,0.143 10 G56 5.848,0.437 6.154,0.579 0.306,0.141 10 32*1 5.847,0.888 6.155,1.031 0.309,0.143 10 31*1 4.502,3.085 6.394,3.408 1.893,0.323 10 *2: for 1GR-FE and Automatic Transmission System 4.502,2.483 6.251,2.800 1.749,0.318 10 *1: for 1GR-FE and Manual Transmission System 4.502,3.674 6.444,3.816 1.942,0.142 10 *3: for 1KD-FTV 4.497,3.944 6.439,4.086 1.942,0.142 10 *4: for 2TR-FE 4.497,4.49 6.439,4.632 1.942,0.142 10 *6: except 2TR-FE 4.497,4.192 6.439,4.333 1.942,0.142 10 *5: for 1GD-FTV

C294468E03
5.977,2.406 6.387,2.547 0.411,0.141 10 CANH 5.766,2.318 6.177,2.459 0.411,0.141 10 9 5.693,2.771 6.086,2.914 0.393,0.143 10 10 5.977,2.859 6.370,3.002 0.393,0.143 10 CANL 5.697,3.239 6.869,3.629 1.172,0.391 10 H56 5.697,3.407 7.004,3.761 1.307,0.354 10 Navigation Receiver Assembly*7 5.977,4.292 6.387,4.433 0.411,0.141 10 CANH 5.766,4.204 6.177,4.345 0.411,0.141 10 9 5.693,4.657 6.086,4.800 0.393,0.143 10 10 5.977,4.745 6.370,4.888 0.393,0.143 10 CANL 5.389,5.097 6.561,5.487 1.172,0.391 10 H51 5.389,5.265 7.147,5.619 1.758,0.354 10 Radio and Display Receiver Assembly*8 3.952,2.318 4.363,2.459 0.411,0.141 10 2 3.97,2.771 4.363,2.914 0.393,0.143 10 13 3.111,0.478 3.522,0.619 0.411,0.141 10 1 3.038,0.931 3.431,1.074 0.393,0.143 10 12 0.282,3.413 2.209,3.767 1.927,0.354 10 Yaw Rate Sensor Assembly 0.779,2.405 1.189,2.547 0.410,0.141 10 CANH 0.796,2.858 1.189,3.001 0.393,0.143 10 CANL 1.304,2.318 1.715,2.459 0.410,0.141 10 3 1.322,2.771 1.715,2.914 0.393,0.143 10 2 0.282,3.245 1.495,3.635 1.213,0.391 10 G52 3.111,2.318 3.522,2.459 0.411,0.141 10 4 3.038,2.771 3.431,2.914 0.393,0.143 10 15 0.282,5.297 1.663,5.652 1.381,0.354 10 Center Airbag Sensor Assembly 0.779,4.29 1.189,4.431 0.410,0.141 10 CANH 0.796,4.743 1.189,4.886 0.393,0.143 10 CANL 1.304,4.202 1.715,4.344 0.410,0.141 10 13 1.322,4.655 1.715,4.798 0.393,0.143 10 22 0.282,5.129 1.495,5.520 1.213,0.391 10 G1 3.952,4.202 4.363,4.344 0.411,0.141 10 6 3.97,4.655 4.363,4.798 0.393,0.143 10 17 3.111,4.202 3.522,4.344 0.411,0.141 10 5 3.038,4.655 3.431,4.798 0.393,0.143 10 16 0.282,7.197 1.936,7.551 1.654,0.354 10 Main Body ECU (Multiplex Network Body ECU) 0.779,6.189 1.189,6.330 0.410,0.141 10 CANH 0.796,6.642 1.189,6.785 0.393,0.143 10 CANL 1.304,6.102 1.715,6.243 0.410,0.141 10 14 1.322,6.555 1.715,6.698 0.393,0.143 10 13 0.282,7.029 1.495,7.419 1.213,0.391 10 G64 3.952,6.102 4.363,6.243 0.411,0.141 10 1 3.97,6.555 4.363,6.698 0.393,0.143 10 12 3.111,6.102 3.522,6.243 0.411,0.141 10 3 3.038,6.555 3.431,6.698 0.393,0.143 10 14 2.84,7.745 4.052,8.136 1.213,0.391 10 G94 2.84,7.914 4.455,8.158 1.616,0.244 10 No. 3 Junction Connector 0.191,8.272 6.422,8.418 6.231,0.146 10 *7: w/ Navigation System (for Navigation Receiver Type) 0.191,8.545 6.108,8.691 5.917,0.146 10 *8: w/ Navigation System (for Radio and Display Type) or w/o Navigation System 5.977,0.565 6.387,0.706 0.411,0.141 10 CANH 5.977,1.018 6.370,1.161 0.393,0.143 10 CANL 5.766,0.478 6.177,0.619 0.411,0.141 10 4 5.766,0.931 6.160,1.074 0.393,0.143 10 3 3.952,0.478 4.363,0.619 0.411,0.141 10 3 3.97,0.931 4.363,1.074 0.393,0.143 10 14 5.354,1.393 6.526,1.784 1.172,0.391 10 G33 5.354,1.561 7.112,1.916 1.758,0.354 10 Spiral Cable Sub-assembly (Steering Angle Sensor) 2.891,5.061 4.104,5.452 1.213,0.391 10 G100 2.891,5.229 4.507,5.473 1.616,0.244 10 No. 2 Junction Connector

C294451E06
5.949,0.756 6.359,0.897 0.411,0.141 10 CANH 5.949,1.402 6.342,1.545 0.393,0.143 10 CANL 5.668,0.756 6.079,0.897 0.411,0.141 10 40 5.665,1.223 6.058,1.365 0.393,0.143 10 39 5.739,1.692 6.911,2.083 1.172,0.391 10 G6 5.739,1.828 6.935,2.182 1.196,0.354 10 Combination Meter Assembly 4.33,3.547 4.791,3.698 0.461,0.151 10 *6 4.33,3.988 4.791,4.139 0.461,0.151 10 *6 4.33,4.845 4.791,4.996 0.461,0.151 10 *6 4.33,5.286 4.791,5.437 0.461,0.151 10 *6 2.368,3.547 2.829,3.698 0.461,0.151 10 *6 2.368,3.988 2.829,4.139 0.461,0.151 10 *6 5.949,4.948 6.359,5.089 0.411,0.141 10 CANH 5.949,5.401 6.342,5.544 0.393,0.143 10 CANL 0.584,1.856 2.512,2.210 1.927,0.354 10 DLC3 0.754,0.848 1.165,0.990 0.410,0.141 10 CANH 0.772,1.301 1.165,1.444 0.393,0.143 10 CANL 1.28,0.761 1.690,0.902 0.410,0.141 10 6 1.297,1.214 1.690,1.357 0.393,0.143 10 14 0.584,1.688 1.797,2.078 1.213,0.391 10 G48 3.928,0.756 4.484,0.897 0.556,0.141 10 2 3.928,1.209 4.460,1.351 0.533,0.143 10 13 3.087,0.761 3.497,0.902 0.410,0.141 10 5 3.013,1.214 3.407,1.357 0.393,0.143 10 16 3.924,3.549 4.335,3.690 0.411,0.141 10 10 3.942,4.002 4.335,4.144 0.393,0.143 10 21 3.083,3.549 3.494,3.690 0.411,0.141 10 9 3.01,4.002 3.403,4.144 0.393,0.143 10 20 3.081,2.058 3.539,2.200 0.457,0.141 10 6 2.996,2.511 3.538,2.654 0.542,0.143 10 17 3.924,4.82 4.335,4.961 0.411,0.141 10 11 3.942,5.273 4.335,5.415 0.393,0.143 10 22 5.64,4.82 6.051,4.961 0.411,0.141 10 11 5.658,5.273 6.051,5.415 0.393,0.143 10 25 2.812,2.908 4.024,3.299 1.213,0.391 10 G94 2.812,3.076 4.427,3.320 1.616,0.244 10 No. 3 Junction Connector 5.326,5.769 6.498,6.159 1.172,0.391 10 A7 5.326,5.937 7.084,6.291 1.758,0.354 10 Master Cylinder Solenoid (Skid Control ECU)*6 2.863,5.768 4.076,6.158 1.213,0.391 10 A73 2.863,5.936 4.819,6.180 1.956,0.244 10 No. 5 Junction Connector*6 0.38,6.011 1.487,6.157 1.107,0.146 10 *4: for 2TR-FE 0.38,6.291 1.964,6.437 1.584,0.146 10 *6 : except 2TR-FE 4.352,0.756 4.908,0.897 0.556,0.141 10 *4 4.352,1.209 4.884,1.351 0.533,0.143 10 *4

CAUTION / NOTICE / HINT

HINT:
·

Perform the following inspection for the ECUs (sensors) which are not displayed on the GTS. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.



PROCEDURE

1.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU)
a.

Disconnect the A6 brake actuator assembly (skid control ECU)*1 or A7 master cylinder solenoid (skid control ECU)*2 connector.

*1: for 2TR-FE

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV



b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS (for 2TR-FE) A
"Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS (for 1GR-FE, 1KD-FTV, 1GD-FTV) B
Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the GTS C



A

2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

B

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)

C

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
2.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U148256E01
0.118,0.031 0.316,0.229 0.198,0.198 10 *a 1.683,0.083 1.969,0.269 0.286,0.186 10 A6 0.218,1.676 0.658,1.822 0.440,0.147 10 CANL 0.408,1.871 0.848,2.040 0.440,0.169 10 CANH 1.315,1.343 1.042,1.944 1.042,1.944 0.936,1.944 false 1.315,1.217 0.8,1.754 0.8,1.754 0.722,1.754 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

3.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U115863E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.881,0.849 0.286,0.186 10 A7 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU)

4.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU)
a.

Disconnect the G64 main body ECU (multiplex network body ECU) connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" is not displayed on the GTS A
Several ECUs and sensors in addition to "Main Body" are displayed on the GTS B



A

5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)

B

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
5.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
U148348E06
1.271,0.458 1.365,0.458 1.365,0.458 1.604,1.177 false 1.521,1.198 1.031,0.719 1.031,0.719 0.948,0.719 false 0.052,0 0.292,0.188 0.24,0.188 10 false *a 0.521,0.635 0.948,0.792 0.427,0.156 10 false CANH 0.885,0.375 1.292,0.531 0.406,0.156 10 false CANL 0.458,1.115 0.792,1.271 0.333,0.156 10 false G64

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (MAIN BODY ECU)

6.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the G1 center airbag sensor assembly connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Airbag" is not displayed on the GTS A
Several ECUs and sensors in addition to "Airbag" are displayed on the GTS B



A

7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)

B

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
7.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CENTER AIRBAG SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U148246E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 0.132,1.336 0.551,1.513 0.419,0.177 10 CANH 0.295,0.987 0.560,1.164 0.266,0.177 10 G1 0.312,1.769 0.732,1.946 0.419,0.177 10 CANL 1.279,1.077 0.725,1.419 0.725,1.419 0.652,1.419 false 1.176,1.487 0.95,1.863 0.95,1.863 0.823,1.863 false

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CENTER AIRBAG SENSOR ASSEMBLY)

8.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR)
a.

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Spiral cable (Steering Angle Sensor)" is not displayed on the GTS A
Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the GTS B



A

9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)

B

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
9.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U148232E07
2.031,1.563 1.708,1.167 1.708,1.167 1.635,1.167 false 2.135,1.563 2.385,1.302 2.385,1.302 2.469,1.302 false 1.219,1.094 1.646,1.292 0.427,0.198 10 false CANH 0.885,1.448 1.208,1.646 0.323,0.198 10 false G33 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.51,1.219 2.927,1.417 0.417,0.198 10 false CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR)

10.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU)
a.

Disconnect the G53 four wheel drive control ECU connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Four Wheel Drive Control" is not displayed on the GTS A
Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the GTS B



A

11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)

B

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU)
11.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (FOUR WHEEL DRIVE CONTROL ECU CAN BRANCH WIRE)
a.
U148352E06
0.479,1.01 0.563,1.01 0.563,1.01 0.677,1.344 false 0.583,0.708 0.677,0.708 0.677,0.708 0.75,1.354 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.156,0.625 0.583,0.781 0.427,0.156 10 false CANH 0.094,0.948 0.49,1.104 0.396,0.156 10 false CANL 2.417,1.229 2.719,1.385 0.302,0.156 10 false G53

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU)

12.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU)
a.

Disconnect the G38 certification ECU (smart key ECU assembly) connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Certification (Smart)" is not displayed on the GTS A
Several ECUs and sensors in addition to "Certification (Smart)" are displayed on the GTS B



A

13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU CAN BRANCH WIRE)

B

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
13.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (CERTIFICATION ECU CAN BRANCH WIRE)
a.
U148226E06
1.219,1.552 1,0.948 1,0.948 0.927,0.948 false 1.146,1.552 0.656,1.156 0.656,1.156 0.583,1.156 false 0.49,0.875 0.917,1.031 0.427,0.156 10 false CANH 0.177,1.083 0.573,1.24 0.396,0.156 10 false CANL 2.5,1.417 2.823,1.573 0.323,0.156 10 false G38 0.073,0 0.396,0.156 0.323,0.156 10 false *a

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (CERTIFICATION ECU)

14.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY)
a.

Disconnect the G46 power steering ECU assembly connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"PPS" is not displayed on the GTS A
Several ECUs and sensors in addition to "PPS" are displayed on the GTS B



A

15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)

B

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU)
15.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U148345E06
1.917,1.531 2.135,1.073 2.135,1.073 2.229,1.073 false 2.365,1.26 2.292,1.26 2.292,1.26 2.021,1.531 false 0.063,0 0.333,0.229 0.271,0.229 10 false *a 2.417,1.188 2.844,1.354 0.427,0.167 10 false CANH 2.26,0.99 2.677,1.156 0.417,0.167 10 false CANL 0.635,1.365 0.958,1.531 0.323,0.167 10 false G46

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

16.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the G51 power management control ECU connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Power Management1" is not displayed on the GTS A
Several ECUs and sensors in addition to "Power Management1" are displayed on the GTS B



A

17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)

B

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY)
17.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)
a.
C348088E05
0.646,1.177 1.083,1.5 0.438,0.323 1.302,2 1.458,2 1.458,2 1.792,1.302 true 1.083,1.813 1.24,1.813 1.24,1.813 1.729,1.302 true 0.083,0.156 0.396,0.354 0.313,0.198 10 false *a 0.688,1.729 1.313,1.958 0.625,0.229 10 false CA1H 0.927,1.927 1.552,2.156 0.625,0.229 10 false CA1L 0.729,1.26 1.354,1.49 0.625,0.229 10 false G51

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU)

18.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY)
a.

Disconnect the G52 yaw rate sensor assembly connector.


b.

Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Yaw Rate Sensor" is not displayed on the GTS A
Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the GTS (w/ Navigation System [for Navigation Receiver Type]) B
Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the GTS (w/ Navigation System [for Radio and Display Type] or w/o Navigation System) C



A

19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)

B

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY)

C

21.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
19.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (YAW RATE SENSOR ASSEMBLY CAN BRANCH WIRE)
a.
U148301E02
0.875,1.01 0.969,1.01 0.969,1.01 1.396,1.469 false 1.177,0.542 1.292,0.542 1.292,0.542 1.573,1.469 false 0.063,0.094 0.24,0.271 0.177,0.177 10 false *a 0.448,0.917 0.854,1.094 0.406,0.177 10 false CANL 0.438,1.448 0.74,1.625 0.302,0.177 10 false G52 0.719,0.438 1.146,0.615 0.427,0.177 10 false CANH

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (YAW RATE SENSOR ASSEMBLY)

20.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY)
a.
U170266E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.581,0.371 1.855,0.512 0.274,0.140 10 H56 2.039,1.299 2.26,1.825 2.26,1.825 2.366,1.825 false 1.908,1.299 1.687,1.825 1.687,1.825 1.581,1.825 false 1.079,1.75 1.490,1.889 0.411,0.139 10 CANH 2.398,1.75 2.809,1.889 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Disconnect the H56 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

21.CHECK FOR OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U148880E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.

Disconnect the H51 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)