Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2016.08–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area
The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

Brake actuator assembly (skid control ECU)*1

·

Master cylinder solenoid (skid control ECU)*2

·

Four wheel drive control ECU

·

Certification ECU (smart key ECU assembly)

·

Power management control ECU

·

Power steering ECU assembly

·

Navigation receiver assembly*3

·

Radio and display receiver assembly*4

·

Spiral cable sub-assembly (steering angle sensor)

·

Yaw rate sensor assembly

·

Center airbag sensor assembly

·

Main body ECU (multiplex network body ECU)

·

Telematics transceiver*5

·

Combination meter assembly

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

No. 4 junction connector*1

·

No. 5 junction connector*2



*1: for 2TR-FE

*2: for 1GR-FE, 1KD-FTV, 1GD-FTV

*3: w/ Navigation System (for Navigation Receiver Type)

*4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System

*5: w/ Telematics Transceiver


WIRING DIAGRAM

C348117E01
6.24,0.198 6.823,0.375 0.583,0.177 10 false CANH 6.24,0.917 6.823,1.094 0.583,0.177 10 false CANL 6.333,1.198 6.917,1.375 0.583,0.177 10 false ECM 4.198,0.333 4.563,0.51 0.365,0.177 10 false G184 4.594,0.333 4.958,0.51 0.365,0.177 10 false G181 5.031,0.333 5.396,0.51 0.365,0.177 10 false G58 5.438,0.333 5.802,0.51 0.365,0.177 10 false G56 5.833,0.333 6.198,0.51 0.365,0.177 10 false G56 4.219,0.135 4.583,0.313 0.365,0.177 10 false 17*5 4.615,0.135 4.979,0.313 0.365,0.177 10 false 13*4 5.031,0.135 5.396,0.313 0.365,0.177 10 false 35*3 5.448,0.135 5.813,0.313 0.365,0.177 10 false 31*2 5.833,0.135 6.198,0.313 0.365,0.177 10 false 32*1 4.188,0.792 4.552,0.969 0.365,0.177 10 false G184 4.604,0.771 4.969,0.948 0.365,0.177 10 false G181 5.042,0.771 5.406,0.948 0.365,0.177 10 false G58 5.438,0.781 5.802,0.958 0.365,0.177 10 false G56 5.854,0.781 6.219,0.958 0.365,0.177 10 false G56 4.208,0.563 4.573,0.74 0.365,0.177 10 false 28*5 4.615,0.563 4.979,0.74 0.365,0.177 10 false 14*4 5.021,0.563 5.385,0.74 0.365,0.177 10 false 36*3 5.406,0.573 5.771,0.75 0.365,0.177 10 false 25*2 5.813,0.573 6.177,0.75 0.365,0.177 10 false 31*1 2.938,0.229 3.198,0.406 0.26,0.177 10 false 10 2.938,0.667 3.198,0.844 0.26,0.177 10 false 21 2.052,0.219 2.313,0.396 0.26,0.177 10 false 11 2.052,0.656 2.313,0.833 0.26,0.177 10 false 22 3.302,0.219 3.563,0.396 0.26,0.177 10 false *4 3.292,0.667 3.552,0.844 0.26,0.177 10 false *4 1.656,0.208 1.917,0.385 0.26,0.177 10 false *4 1.656,0.656 1.917,0.833 0.26,0.177 10 false *4 1.313,0.208 1.573,0.385 0.26,0.177 10 false 25 1.313,0.667 1.573,0.844 0.26,0.177 10 false 14 0.802,0.323 1.385,0.5 0.583,0.177 10 false CANH 0.844,0.813 1.427,0.99 0.583,0.177 10 false CANL 2.938,1.563 3.198,1.74 0.26,0.177 10 false 9 2.927,2 3.188,2.177 0.26,0.177 10 false 20 3.344,1.552 3.604,1.729 0.26,0.177 10 false *4 3.344,2.021 3.604,2.198 0.26,0.177 10 false *4 0.073,1.271 1.698,1.75 1.625,0.479 10 false Brake Actuator Assembly (Skid Control ECU)*4 0.073,1.115 1.698,1.594 1.625,0.479 10 false A6 1.698,2.531 3.563,2.75 1.865,0.219 10 false No. 4 Junction Connector*4 1.708,2.375 3.573,2.594 1.865,0.219 10 false A72 3.854,1.229 4.115,1.406 0.26,0.177 10 false *6 4.135,1.229 4.396,1.406 0.26,0.177 10 false *6 3.354,3.188 3.615,3.365 0.26,0.177 10 false 6 3.344,3.635 3.604,3.813 0.26,0.177 10 false 17 2.531,3.167 2.792,3.344 0.26,0.177 10 false 2 2.469,3.646 2.729,3.823 0.26,0.177 10 false 13 3.385,4.094 3.646,4.271 0.26,0.177 10 false 3 3.344,4.542 3.604,4.719 0.26,0.177 10 false 14 2.531,4.927 2.792,5.104 0.26,0.177 10 false 4 3.344,6.052 3.604,6.229 0.26,0.177 10 false 16 3.344,5.573 3.604,5.75 0.26,0.177 10 false 5 2.479,5.375 2.74,5.552 0.26,0.177 10 false 15 2.542,7.188 2.802,7.365 0.26,0.177 10 false 1 2.469,7.667 2.729,7.844 0.26,0.177 10 false 12 3.365,7.208 3.625,7.385 0.26,0.177 10 false 7 3.344,7.667 3.604,7.844 0.26,0.177 10 false 18 2.219,8.406 4.083,8.625 1.865,0.219 10 false No. 1 Junction Connector 2.219,8.26 4.083,8.479 1.865,0.219 10 false G193 1.313,3.167 1.573,3.344 0.26,0.177 10 false 19 1.333,3.604 1.594,3.781 0.26,0.177 10 false 20 0.833,3.323 1.417,3.5 0.583,0.177 10 false CANH 0.833,3.76 1.417,3.938 0.583,0.177 10 false CANL 0.094,4.25 2.042,4.458 1.948,0.208 10 false Four Wheel Drive Control ECU 0.094,4.115 2.042,4.323 1.948,0.208 10 false G53 5.979,4.229 6.563,4.406 0.583,0.177 10 false CANH 5.979,4.688 6.563,4.865 0.583,0.177 10 false CANL 5.74,4.094 6,4.271 0.26,0.177 10 false 9 5.688,4.563 5.948,4.74 0.26,0.177 10 false 10 4.333,5.083 7.156,5.365 2.823,0.281 10 false Certification ECU (Smart Key ECU Assembly) 4.333,4.938 6.281,5.146 1.948,0.208 10 false G38 1.333,4.938 1.594,5.115 0.26,0.177 10 false 14 1.344,5.375 1.604,5.552 0.26,0.177 10 false 13 0.823,5.063 1.406,5.24 0.583,0.177 10 false CA1H 0.823,5.51 1.406,5.688 0.583,0.177 10 false CA1L 0.073,6 2.25,6.198 2.177,0.198 10 false Power Management Control ECU 0.073,5.865 2.25,6.063 2.177,0.198 10 false G51 5.979,5.74 6.563,5.917 0.583,0.177 10 false CANH 5.99,6.188 6.573,6.365 0.583,0.177 10 false CANL 5.75,5.615 6.01,5.792 0.26,0.177 10 false 1 5.75,6.042 6.01,6.219 0.26,0.177 10 false 2 5.125,6.625 7.156,6.875 2.031,0.25 10 false Power Steering ECU Assembly 5.125,6.5 7.156,6.75 2.031,0.25 10 false G46 5.583,8.25 7.156,8.5 1.573,0.25 10 false Telematics Transceiver*9 5.552,8.104 7.042,8.354 1.49,0.25 10 false G187 5.99,7.333 6.573,7.51 0.583,0.177 10 false CANP 5.99,7.813 6.573,7.99 0.583,0.177 10 false CANN 5.688,7.219 5.948,7.396 0.26,0.177 10 false 15 5.688,7.667 5.948,7.844 0.26,0.177 10 false 16 4.427,1.5 6.094,1.885 1.667,0.385 10 false *1: for 1GR-FE and Manual Transmission System 4.417,2.146 6.26,2.563 1.844,0.417 10 false *2: for 1GR-FE and Automatic Transmission System 4.417,2.813 5.552,3 1.135,0.188 10 false *3: for 1KD-FTV 4.417,3.146 5.552,3.333 1.135,0.188 10 false *5: for 1GD-FTV 5.698,2.833 6.833,3.021 1.135,0.188 10 false *4: for 2TR-FE 5.698,3.167 6.896,3.406 1.198,0.24 10 false *6: except 2TR-FE 4.417,3.479 6.833,3.667 2.417,0.188 10 false *9: w/ Telematics Transceiver

C294468E03
5.977,2.406 6.387,2.547 0.411,0.141 10 CANH 5.766,2.318 6.177,2.459 0.411,0.141 10 9 5.693,2.771 6.086,2.914 0.393,0.143 10 10 5.977,2.859 6.370,3.002 0.393,0.143 10 CANL 5.697,3.239 6.869,3.629 1.172,0.391 10 H56 5.697,3.407 7.004,3.761 1.307,0.354 10 Navigation Receiver Assembly*7 5.977,4.292 6.387,4.433 0.411,0.141 10 CANH 5.766,4.204 6.177,4.345 0.411,0.141 10 9 5.693,4.657 6.086,4.800 0.393,0.143 10 10 5.977,4.745 6.370,4.888 0.393,0.143 10 CANL 5.389,5.097 6.561,5.487 1.172,0.391 10 H51 5.389,5.265 7.147,5.619 1.758,0.354 10 Radio and Display Receiver Assembly*8 3.952,2.318 4.363,2.459 0.411,0.141 10 2 3.97,2.771 4.363,2.914 0.393,0.143 10 13 3.111,0.478 3.522,0.619 0.411,0.141 10 1 3.038,0.931 3.431,1.074 0.393,0.143 10 12 0.282,3.413 2.209,3.767 1.927,0.354 10 Yaw Rate Sensor Assembly 0.779,2.405 1.189,2.547 0.410,0.141 10 CANH 0.796,2.858 1.189,3.001 0.393,0.143 10 CANL 1.304,2.318 1.715,2.459 0.410,0.141 10 3 1.322,2.771 1.715,2.914 0.393,0.143 10 2 0.282,3.245 1.495,3.635 1.213,0.391 10 G52 3.111,2.318 3.522,2.459 0.411,0.141 10 4 3.038,2.771 3.431,2.914 0.393,0.143 10 15 0.282,5.297 1.663,5.652 1.381,0.354 10 Center Airbag Sensor Assembly 0.779,4.29 1.189,4.431 0.410,0.141 10 CANH 0.796,4.743 1.189,4.886 0.393,0.143 10 CANL 1.304,4.202 1.715,4.344 0.410,0.141 10 13 1.322,4.655 1.715,4.798 0.393,0.143 10 22 0.282,5.129 1.495,5.520 1.213,0.391 10 G1 3.952,4.202 4.363,4.344 0.411,0.141 10 6 3.97,4.655 4.363,4.798 0.393,0.143 10 17 3.111,4.202 3.522,4.344 0.411,0.141 10 5 3.038,4.655 3.431,4.798 0.393,0.143 10 16 0.282,7.197 1.936,7.551 1.654,0.354 10 Main Body ECU (Multiplex Network Body ECU) 0.779,6.189 1.189,6.330 0.410,0.141 10 CANH 0.796,6.642 1.189,6.785 0.393,0.143 10 CANL 1.304,6.102 1.715,6.243 0.410,0.141 10 14 1.322,6.555 1.715,6.698 0.393,0.143 10 13 0.282,7.029 1.495,7.419 1.213,0.391 10 G64 3.952,6.102 4.363,6.243 0.411,0.141 10 1 3.97,6.555 4.363,6.698 0.393,0.143 10 12 3.111,6.102 3.522,6.243 0.411,0.141 10 3 3.038,6.555 3.431,6.698 0.393,0.143 10 14 2.84,7.745 4.052,8.136 1.213,0.391 10 G94 2.84,7.914 4.455,8.158 1.616,0.244 10 No. 3 Junction Connector 0.191,8.272 6.422,8.418 6.231,0.146 10 *7: w/ Navigation System (for Navigation Receiver Type) 0.191,8.545 6.108,8.691 5.917,0.146 10 *8: w/ Navigation System (for Radio and Display Type) or w/o Navigation System 5.977,0.565 6.387,0.706 0.411,0.141 10 CANH 5.977,1.018 6.370,1.161 0.393,0.143 10 CANL 5.766,0.478 6.177,0.619 0.411,0.141 10 4 5.766,0.931 6.160,1.074 0.393,0.143 10 3 3.952,0.478 4.363,0.619 0.411,0.141 10 3 3.97,0.931 4.363,1.074 0.393,0.143 10 14 5.354,1.393 6.526,1.784 1.172,0.391 10 G33 5.354,1.561 7.112,1.916 1.758,0.354 10 Spiral Cable Sub-assembly (Steering Angle Sensor) 2.891,5.061 4.104,5.452 1.213,0.391 10 G100 2.891,5.229 4.507,5.473 1.616,0.244 10 No. 2 Junction Connector

C294451E06
5.949,0.756 6.359,0.897 0.411,0.141 10 CANH 5.949,1.402 6.342,1.545 0.393,0.143 10 CANL 5.668,0.756 6.079,0.897 0.411,0.141 10 40 5.665,1.223 6.058,1.365 0.393,0.143 10 39 5.739,1.692 6.911,2.083 1.172,0.391 10 G6 5.739,1.828 6.935,2.182 1.196,0.354 10 Combination Meter Assembly 4.33,3.547 4.791,3.698 0.461,0.151 10 *6 4.33,3.988 4.791,4.139 0.461,0.151 10 *6 4.33,4.845 4.791,4.996 0.461,0.151 10 *6 4.33,5.286 4.791,5.437 0.461,0.151 10 *6 2.368,3.547 2.829,3.698 0.461,0.151 10 *6 2.368,3.988 2.829,4.139 0.461,0.151 10 *6 5.949,4.948 6.359,5.089 0.411,0.141 10 CANH 5.949,5.401 6.342,5.544 0.393,0.143 10 CANL 0.584,1.856 2.512,2.210 1.927,0.354 10 DLC3 0.754,0.848 1.165,0.990 0.410,0.141 10 CANH 0.772,1.301 1.165,1.444 0.393,0.143 10 CANL 1.28,0.761 1.690,0.902 0.410,0.141 10 6 1.297,1.214 1.690,1.357 0.393,0.143 10 14 0.584,1.688 1.797,2.078 1.213,0.391 10 G48 3.928,0.756 4.484,0.897 0.556,0.141 10 2 3.928,1.209 4.460,1.351 0.533,0.143 10 13 3.087,0.761 3.497,0.902 0.410,0.141 10 5 3.013,1.214 3.407,1.357 0.393,0.143 10 16 3.924,3.549 4.335,3.690 0.411,0.141 10 10 3.942,4.002 4.335,4.144 0.393,0.143 10 21 3.083,3.549 3.494,3.690 0.411,0.141 10 9 3.01,4.002 3.403,4.144 0.393,0.143 10 20 3.081,2.058 3.539,2.200 0.457,0.141 10 6 2.996,2.511 3.538,2.654 0.542,0.143 10 17 3.924,4.82 4.335,4.961 0.411,0.141 10 11 3.942,5.273 4.335,5.415 0.393,0.143 10 22 5.64,4.82 6.051,4.961 0.411,0.141 10 11 5.658,5.273 6.051,5.415 0.393,0.143 10 25 2.812,2.908 4.024,3.299 1.213,0.391 10 G94 2.812,3.076 4.427,3.320 1.616,0.244 10 No. 3 Junction Connector 5.326,5.769 6.498,6.159 1.172,0.391 10 A7 5.326,5.937 7.084,6.291 1.758,0.354 10 Master Cylinder Solenoid (Skid Control ECU)*6 2.863,5.768 4.076,6.158 1.213,0.391 10 A73 2.863,5.936 4.819,6.180 1.956,0.244 10 No. 5 Junction Connector*6 0.38,6.011 1.487,6.157 1.107,0.146 10 *4: for 2TR-FE 0.38,6.291 1.964,6.437 1.584,0.146 10 *6 : except 2TR-FE 4.352,0.756 4.908,0.897 0.556,0.141 10 *4 4.352,1.209 4.884,1.351 0.533,0.143 10 *4

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
2.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
U149542E01
0.226,1.132 0.560,1.305 0.333,0.173 10 G48 2.319,0.355 2.767,0.528 0.448,0.173 10 CANH 0.087,0.011 0.277,0.184 0.191,0.173 10 *a 1.228,1.724 1.626,1.897 0.398,0.173 10 CANL 1.977,0.875 2.233,0.448 2.233,0.448 2.305,0.448 false 1.965,1.437 1.821,1.811 1.821,1.811 1.722,1.811 false

Disconnect the G94 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 1 MΩ or higher


Text in Illustration
*a Front view of DLC3



OK

3.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

3.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
U149542E01
0.226,1.132 0.560,1.305 0.333,0.173 10 G48 2.319,0.355 2.767,0.528 0.448,0.173 10 CANH 0.087,0.011 0.277,0.184 0.191,0.173 10 *a 1.228,1.724 1.626,1.897 0.398,0.173 10 CANL 1.977,0.875 2.233,0.448 2.233,0.448 2.305,0.448 false 1.965,1.437 1.821,1.811 1.821,1.811 1.722,1.811 false

Disconnect the G193 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)

NG

35.CONNECT CONNECTOR
5.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - FOUR WHEEL DRIVE CONTROL ECU)
a.
U148899E03
2.521,1 2.417,1 2.417,1 2.167,1.229 false 2.167,1.438 2.385,1.719 2.385,1.719 2.51,1.719 false 2.531,0.917 2.948,1.052 0.417,0.135 10 false CANH 2.521,1.635 2.917,1.771 0.396,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.417,1.24 0.792,1.406 0.375,0.167 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-2 (CANH) - G193-13 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CERTIFICATION ECU)

NG

11.CONNECT CONNECTOR
6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CERTIFICATION ECU)
a.
U148900E03
2.5,0.865 2.396,0.865 2.396,0.865 2.052,1.229 false 2.052,1.438 2.302,1.781 2.302,1.781 2.417,1.781 false 2.51,0.792 2.927,0.927 0.417,0.135 10 false CANH 2.427,1.698 2.823,1.833 0.396,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.427,1.25 0.833,1.417 0.406,0.167 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-3 (CANH) - G193-14 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

13.CONNECT CONNECTOR
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U148901E03
2.49,0.802 2.385,0.802 2.385,0.802 1.948,1.229 false 1.948,1.438 2.229,1.823 2.229,1.823 2.354,1.823 false 2.51,0.729 2.927,0.865 0.417,0.135 10 false CANH 2.365,1.74 2.76,1.875 0.396,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.427,1.25 0.813,1.438 0.385,0.188 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-4 (CANH) - G193-15 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

NG

15.CONNECT CONNECTOR
8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.
U148902E03
2.458,0.729 2.365,0.729 2.365,0.729 1.854,1.229 false 1.854,1.438 2.219,1.865 2.219,1.865 2.333,1.865 false 2.479,0.656 2.896,0.792 0.417,0.135 10 false CANH 2.344,1.781 2.74,1.917 0.396,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.417,1.25 0.813,1.438 0.396,0.188 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-5 (CANH) - G193-16 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)

NG

17.CONNECT CONNECTOR
9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - TELEMATICS TRANSCEIVER)
NOTICE:

For vehicles without a telematics transceiver, go to "Check for Short in CAN Bus Wires (NO. 1 Junction Connector - ECM or NO. 4 Junction Connector)".


a.
U148895E05
2.385,0.635 2.281,0.635 2.281,0.635 1.625,1.229 true 1.625,1.406 1.958,1.938 1.958,1.938 2.083,1.938 true 2.396,0.552 3,0.688 0.604,0.135 10 false CANH 2.104,1.854 2.677,1.99 0.573,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.375,1.25 0.771,1.427 0.396,0.177 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-7 (CANH) - G193-18 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)

NG

19.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM OR NO. 4 JUNCTION CONNECTOR)
a.
U148895E06
2.385,0.635 2.281,0.635 2.281,0.635 1.75,1.229 false 1.75,1.438 1.958,1.938 1.958,1.938 2.083,1.938 false 2.396,0.552 3,0.688 0.604,0.135 10 false CANH 2.104,1.854 2.677,1.99 0.573,0.135 10 false CANL 0.063,0.083 0.458,0.219 0.396,0.135 10 false *a 0.365,1.25 0.75,1.427 0.385,0.177 10 false G193

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G193-6 (CANH) - G193-17 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)

Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 1GD-FTV) D
NG (for 2TR-FE) E



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

21.CONNECT CONNECTOR

C

23.CONNECT CONNECTOR

D

25.CONNECT CONNECTOR

E

27.CONNECT CONNECTOR
11.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)
12.CHECK FOR SHORT IN CAN BUS WIRES (FOUR WHEEL DRIVE CONTROL ECU)
a.
U148352E05
0.479,1.01 0.563,1.01 0.563,1.01 0.677,1.344 false 0.594,0.708 0.688,0.708 0.688,0.708 0.76,1.354 false 0.052,0 0.219,0.188 0.167,0.188 10 false *a 0.177,0.615 0.604,0.771 0.427,0.156 10 false CANH 0.083,0.938 0.479,1.094 0.396,0.156 10 false CANL 2.438,1.229 2.74,1.385 0.302,0.156 10 false G53

Disconnect the G53 four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

REPLACE FOUR WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FOUR WHEEL DRIVE CONTROL ECU (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
14.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)
a.
U148225E04
1.219,1.552 1,0.948 1,0.948 0.927,0.948 false 1.146,1.552 0.656,1.156 0.656,1.156 0.583,1.156 false 0.5,0.865 0.927,1.021 0.427,0.156 10 false CANH 0.208,1.083 0.604,1.24 0.396,0.156 10 false CANL 2.5,1.417 2.823,1.573 0.323,0.156 10 false G38 0.073,0 0.396,0.156 0.323,0.156 10 false *a

Disconnect the G38 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
16.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
a.
C348088E05
0.646,1.177 1.083,1.5 0.438,0.323 1.302,2 1.458,2 1.458,2 1.792,1.302 true 1.083,1.813 1.24,1.813 1.24,1.813 1.729,1.302 true 0.083,0.156 0.396,0.354 0.313,0.198 10 false *a 0.688,1.729 1.313,1.958 0.625,0.229 10 false CA1H 0.927,1.927 1.552,2.156 0.625,0.229 10 false CA1L 0.729,1.26 1.354,1.49 0.625,0.229 10 false G51

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA1H, CA1L)

17.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY)
a.
U148345E05
1.917,1.531 2.135,1.073 2.135,1.073 2.229,1.073 false 2.365,1.26 2.292,1.26 2.292,1.26 2.021,1.531 false 0.063,0 0.333,0.229 0.271,0.229 10 false *a 2.427,1.188 2.854,1.354 0.427,0.167 10 false CANH 2.271,0.99 2.688,1.156 0.417,0.167 10 false CANL 0.635,1.365 0.958,1.531 0.323,0.167 10 false G46

Disconnect the G46 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER STEERING ECU ASSEMBLY (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (TELEMATICS TRANSCEIVER)
20.CHECK FOR SHORT IN CAN BUS WIRES (TELEMATICS TRANSCEIVER)
a.
U156361E04
1.115,1.802 1.292,1.802 1.292,1.802 1.823,1.167 false 2.292,1.802 2.125,1.802 2.125,1.802 1.906,1.167 false 0.094,0.073 0.531,0.417 0.438,0.344 10 false *a 1.521,0.26 1.99,0.448 0.469,0.188 10 false G187 0.635,1.729 1.115,1.938 0.479,0.208 10 false CANP 2.365,1.719 2.969,1.969 0.604,0.25 10 false CANN

Disconnect the G187 telematics transceiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G187-15 (CANP) - G187-16 (CANN) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Telematics Transceiver)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO TELEMATICS TRANSCEIVER (CANP, CANN)

21.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
22.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170370E01
0.08,0.062 0.282,0.291 0.202,0.230 10 *a 2.405,1.077 2.691,1.219 0.286,0.142 10 G56 1.888,1.976 1.686,1.976 1.686,1.976 1.534,1.573 false 1.306,1.57 1.194,1.717 1.194,1.717 1.039,1.717 false 0.304,1.64 0.902,1.956 0.598,0.316 10 CANL*A, CANH*B 1.302,1.374 1.102,1.156 1.102,1.156 0.947,1.156 false 0.212,1.078 0.810,1.394 0.598,0.316 10 CANL*B 1.927,1.898 2.515,2.040 0.588,0.142 10 CANH*A

Disconnect the G56 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission System
Tester Connection Switch Condition Specified Condition
G56-32 (CANH) - G56-31 (CANL) Engine switch off 108 to 132 Ω

for Automatic Transmission System
Tester Connection Switch Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*A for Manual Transmission System
*B for Automatic Transmission System
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
24.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170369E01
0.08,0.062 0.282,0.291 0.202,0.230 10 *a 0.485,1.077 0.770,1.219 0.286,0.142 10 G58 2.087,1.573 2.2,1.72 2.2,1.72 2.355,1.72 false 2.335,1.976 2.133,1.976 2.133,1.976 1.982,1.573 false 2.383,1.643 2.867,1.785 0.483,0.142 10 CANL 2.36,1.898 2.843,2.040 0.483,0.142 10 CANH

Disconnect the G58 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
26.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170532E01
0.08,0.044 0.282,0.274 0.202,0.230 10 *a 2.675,1.17 3.035,1.312 0.360,0.142 10 G184 0.681,1.806 0.883,1.806 0.883,1.806 1.104,1.612 false 0.681,1.16 0.883,1.16 0.883,1.16 1.104,1.353 false 0.152,1.718 0.635,1.860 0.483,0.142 10 CANL 0.143,1.065 0.627,1.207 0.483,0.142 10 CANH

Disconnect the G184 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-17 (CANH) - G187-28 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
28.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U148890E01
1.032,0.862 1.133,0.862 1.133,0.862 1.414,1.234 false 1.414,1.439 1.227,1.755 1.227,1.755 1.104,1.755 false 0.523,0.784 0.944,0.921 0.421,0.137 10 CANH 0.621,1.674 1.017,1.810 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Disconnect the A72 No. 4 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-9 (CANH) - A72-20 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 4 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

29.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U148903E01
0.856,0.978 0.957,0.978 0.957,0.978 1.199,1.234 false 1.199,1.439 1.012,1.644 1.012,1.644 0.889,1.644 false 0.347,0.9 0.767,1.037 0.421,0.137 10 CANH 0.406,1.562 0.802,1.699 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-11 (CANH) - A72-22 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - ECM)

NG

31.CONNECT CONNECTOR
30.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 JUNCTION CONNECTOR - ECM)
a.
U148889E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-10 (CANH) - A72-21 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 4 Junction Connector)



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

33.CONNECT CONNECTOR
31.CONNECT CONNECTOR
a.

Reconnect the A72 No. 4 junction connector.



NEXT

32.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
32.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U148256E01
0.118,0.031 0.316,0.229 0.198,0.198 10 *a 1.683,0.083 1.969,0.269 0.286,0.186 10 A6 0.218,1.676 0.658,1.822 0.440,0.147 10 CANL 0.408,1.871 0.848,2.040 0.440,0.169 10 CANH 1.315,1.343 1.042,1.944 1.042,1.944 0.936,1.944 false 1.315,1.217 0.8,1.754 0.8,1.754 0.722,1.754 false

Disconnect the A6 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

33.CONNECT CONNECTOR
a.

Reconnect the A72 No. 4 junction connector.



NEXT

34.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
34.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170531E02
2.594,1.031 2.385,1.031 2.385,1.031 2.104,1.219 false 2.5,0.531 2.292,0.531 2.292,0.531 1.979,1.219 false 0.083,0 0.281,0.229 0.198,0.229 10 false *a 0.365,1.115 0.729,1.26 0.365,0.146 10 false G181 2.635,0.958 3.115,1.104 0.479,0.146 10 false CANL 2.531,0.458 3.01,0.604 0.479,0.146 10 false CANH

Disconnect the G181 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

35.CONNECT CONNECTOR
a.

Reconnect the G193 No. 1 junction connector.



NEXT

36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
36.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U148893E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.424,1.259 0.781,1.396 0.357,0.137 10 G100

Disconnect the G100 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-1 (CANH) - G100-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

37.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
a.
U149542E01
0.226,1.132 0.560,1.305 0.333,0.173 10 G48 2.319,0.355 2.767,0.528 0.448,0.173 10 CANH 0.087,0.011 0.277,0.184 0.191,0.173 10 *a 1.228,1.724 1.626,1.897 0.398,0.173 10 CANL 1.977,0.875 2.233,0.448 2.233,0.448 2.305,0.448 false 1.965,1.437 1.821,1.811 1.821,1.811 1.722,1.811 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of DLC3



OK

38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)

NG

53.CONNECT CONNECTOR
38.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)
NOTICE:

For vehicles without a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Radio and Display Receiver Assembly)".


a.
U148953E01
2.516,0.997 2.415,0.997 2.415,0.997 2.169,1.234 false 2.169,1.439 2.388,1.717 2.388,1.717 2.511,1.717 false 2.534,0.92 2.954,1.057 0.421,0.137 10 CANH 2.522,1.635 2.918,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.39,1.259 0.747,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-2 (CANH) - G100- 13 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

43.CONNECT CONNECTOR
39.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
NOTICE:

For vehicles with a navigation system (for navigation receiver type), go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Steering Angle Sensor)".


a.
U148953E01
2.516,0.997 2.415,0.997 2.415,0.997 2.169,1.234 false 2.169,1.439 2.388,1.717 2.388,1.717 2.511,1.717 false 2.534,0.92 2.954,1.057 0.421,0.137 10 CANH 2.522,1.635 2.918,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.39,1.259 0.747,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-2 (CANH) - G100- 13 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

NG

45.CONNECT CONNECTOR
40.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)
a.
U148954E01
2.497,0.918 2.396,0.918 2.396,0.918 2.07,1.234 false 2.07,1.439 2.289,1.786 2.289,1.786 2.412,1.786 false 2.515,0.84 2.935,0.977 0.421,0.137 10 CANH 2.423,1.704 2.819,1.841 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.39,1.259 0.747,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-3 (CANH) - G100- 14 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)

NG

47.CONNECT CONNECTOR
41.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR ASSEMBLY)
a.
U148955E01
2.482,0.838 2.381,0.838 2.381,0.838 1.976,1.234 false 1.976,1.439 2.285,1.85 2.285,1.85 2.408,1.85 false 2.5,0.761 2.920,0.898 0.421,0.137 10 CANH 2.419,1.768 2.815,1.905 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.39,1.259 0.747,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-4 (CANH) - G100- 15 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NG

49.CONNECT CONNECTOR
42.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)
a.
U148956E01
2.456,0.783 2.355,0.783 2.355,0.783 1.851,1.234 false 1.851,1.439 2.173,1.88 2.173,1.88 2.296,1.88 false 2.474,0.705 2.894,0.842 0.421,0.137 10 CANH 2.307,1.798 2.703,1.935 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.39,1.259 0.747,1.396 0.357,0.137 10 G100

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G100-5 (CANH) - G100- 16 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

51.CONNECT CONNECTOR
43.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

44.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
44.CHECK FOR SHORT IN CAN BUS WIRES (NAVIGATION RECEIVER ASSEMBLY)
a.
U170266E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.581,0.371 1.855,0.512 0.274,0.140 10 H56 2.039,1.299 2.26,1.825 2.26,1.825 2.366,1.825 false 1.908,1.299 1.687,1.825 1.687,1.825 1.581,1.825 false 1.079,1.75 1.490,1.889 0.411,0.139 10 CANH 2.398,1.75 2.809,1.889 0.411,0.139 10 CANL

Disconnect the H56 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)

45.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

46.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
46.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.
U148880E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the H51 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

47.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

48.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
48.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR)
a.
U148232E06
2.031,1.563 1.708,1.167 1.708,1.167 1.635,1.167 false 2.135,1.563 2.385,1.302 2.385,1.302 2.469,1.302 false 1.208,1.083 1.635,1.281 0.427,0.198 10 false CANH 0.875,1.438 1.198,1.635 0.323,0.198 10 false G33 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.51,1.219 2.927,1.417 0.417,0.198 10 false CANL

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)

49.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

50.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
50.CHECK FOR SHORT IN CAN BUS WIRES (YAW RATE SENSOR ASSEMBLY)
a.
U148302E05
0.917,1.01 1.01,1.01 1.01,1.01 1.438,1.469 false 1.188,0.563 1.302,0.563 1.302,0.563 1.583,1.458 false 0.052,0 0.229,0.177 0.177,0.177 10 false *a 0.531,0.938 0.938,1.115 0.406,0.177 10 false CANL 0.417,1.438 0.719,1.615 0.302,0.177 10 false G52 0.75,0.49 1.177,0.667 0.427,0.177 10 false CANH

Disconnect the G52 yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR ASSEMBLY (CANH, CANL)

51.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

52.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
52.CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR ASSEMBLY)
a.
U148246E01
0.041,0 0.230,0.177 0.189,0.177 10 *a 0.132,1.336 0.551,1.513 0.419,0.177 10 CANH 0.295,0.987 0.560,1.164 0.266,0.177 10 G1 0.312,1.769 0.732,1.946 0.419,0.177 10 CANL 1.279,1.077 0.725,1.419 0.725,1.419 0.652,1.419 false 1.176,1.487 0.95,1.863 0.95,1.863 0.823,1.863 false

Disconnect the G1 center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)

53.CONNECT CONNECTOR
a.

Reconnect the G100 No. 2 junction connector.



NEXT

54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
54.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U148891E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.447,1.259 0.731,1.396 0.284,0.137 10 G94

Disconnect the G94 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G94-1 (CANH) - G94-12 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

55.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U148957E01
2.497,0.918 2.396,0.918 2.396,0.918 2.07,1.234 false 2.07,1.439 2.289,1.786 2.289,1.786 2.412,1.786 false 2.515,0.84 2.935,0.977 0.421,0.137 10 CANH 2.423,1.704 2.819,1.841 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.411,1.259 0.699,1.396 0.288,0.137 10 G94

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G94-3 (CANH) - G94-14 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR OR COMBINATION METER ASSEMBLY)

NG

57.CONNECT CONNECTOR
56.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR OR COMBINATION METER ASSEMBLY)
a.
U148892E01
2.497,1.038 2.396,1.038 2.396,1.038 2.158,1.234 false 2.158,1.439 2.343,1.693 2.343,1.693 2.466,1.693 false 2.515,0.961 3.120,1.098 0.605,0.137 10 CANH*B 2.494,1.612 3.064,1.748 0.570,0.137 10 CANL*B 2.383,0.632 2.282,0.632 2.282,0.632 1.754,1.234 false 1.754,1.439 1.956,1.936 1.956,1.936 2.079,1.936 false 2.401,0.555 3.006,0.692 0.605,0.137 10 CANH*A 2.107,1.854 2.677,1.991 0.570,0.137 10 CANL*A 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.447,1.259 0.731,1.396 0.284,0.137 10 G94

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE, 1KD-FTV, 1GD-FTV
Tester Connection Switch Condition Specified Condition
G94-6 (CANH) - G94-17 (CANL) Engine switch off 108 to 132 Ω

for 2TR-FE
Tester Connection Switch Condition Specified Condition
G94-2 (CANH) - G94-13 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*A for 1GR-FE, 1KD-FTV, 1GD-FTV
*B for 2TR-FE
*a Rear view of wire harness connector
(to No. 3 Junction Connector)

Result
Result Proceed to
OK A
NG (for 2TR-FE) B
NG (for 1GR-FE, 1KD-FTV, 1GD-FTV) C



A

REPLACE NO. 3 JUNCTION CONNECTOR

B

59.CONNECT CONNECTOR

C

61.CONNECT CONNECTOR
57.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

58.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
58.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U148348E05
1.271,0.458 1.365,0.458 1.365,0.458 1.604,1.177 false 1.542,1.188 1.052,0.708 1.052,0.708 0.969,0.708 false 0.052,0 0.292,0.188 0.24,0.188 10 false *a 0.552,0.625 0.979,0.781 0.427,0.156 10 false CANH 0.885,0.375 1.292,0.531 0.406,0.156 10 false CANL 0.458,1.104 0.792,1.26 0.333,0.156 10 false G64

Disconnect the G64 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)

59.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

60.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
60.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U148233E01
0.723,0.39 0.931,0.530 0.208,0.139 10 G6 1.935,0.186 2.374,0.322 0.440,0.137 10 CANH 1.724,0.437 2.163,0.574 0.440,0.137 10 CANL 0.074,0.063 0.404,0.245 0.330,0.183 10 *a 2.938,1.372 2.609,0.275 2.609,0.275 2.454,0.275 false 2.809,1.369 2.375,0.514 2.375,0.514 2.221,0.514 false

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)

61.CONNECT CONNECTOR
a.

Reconnect the G94 No. 3 junction connector.



NEXT

62.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
62.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
a.
U148897E01
1.032,0.862 1.133,0.862 1.133,0.862 1.414,1.234 false 1.414,1.439 1.227,1.755 1.227,1.755 1.104,1.755 false 0.523,0.784 0.944,0.921 0.421,0.137 10 CANH 0.621,1.674 1.017,1.810 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A73

Disconnect the A73 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-9 (CANH) - A73-20 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

63.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

63.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - SKID CONTROL ECU)
a.
U148958E01
0.849,0.997 0.95,0.997 0.95,0.997 1.196,1.234 false 1.196,1.439 0.977,1.717 0.977,1.717 0.854,1.717 false 0.33,0.92 0.750,1.057 0.421,0.137 10 CANH 0.391,1.635 0.787,1.772 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.678,1.259 2.944,1.396 0.267,0.137 10 A73

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-11 (CANH) - A73-22 (CANL) Engine switch off 200 Ω or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

64.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

65.CONNECT CONNECTOR
64.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U148898E01
1.006,0.963 1.107,0.963 1.107,0.963 1.31,1.234 false 1.31,1.439 1.171,1.699 1.171,1.699 1.048,1.699 false 0.497,0.886 0.918,1.022 0.421,0.137 10 CANH 0.565,1.618 0.961,1.755 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.682,1.259 2.963,1.396 0.281,0.137 10 A73

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-10 (CANH) - A73-21 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

67.CONNECT CONNECTOR
65.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

66.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
66.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)
a.
U115863E01
0.073,0.08 0.270,0.266 0.197,0.186 10 *a 1.595,0.663 1.881,0.849 0.286,0.186 10 A7 2.493,0.813 2.933,0.999 0.440,0.186 10 CANH 2.864,1.077 3.262,1.246 0.398,0.169 10 CANL 2.207,1.77 2.36,0.902 2.36,0.902 2.465,0.902 false 2.207,1.896 2.765,1.162 2.765,1.162 2.843,1.162 false

Disconnect the A7 master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])



OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

67.CONNECT CONNECTOR
a.

Reconnect the A73 No. 5 junction connector.



NEXT

68.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
68.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U148233E01
0.723,0.39 0.931,0.530 0.208,0.139 10 G6 1.935,0.186 2.374,0.322 0.440,0.137 10 CANH 1.724,0.437 2.163,0.574 0.440,0.137 10 CANL 0.074,0.063 0.404,0.245 0.330,0.183 10 *a 2.938,1.372 2.609,0.275 2.609,0.275 2.454,0.275 false 2.809,1.369 2.375,0.514 2.375,0.514 2.221,0.514 false

Disconnect the G6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)