Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
53292A
1.REMOVE UPPER RADIATOR SUPPORT SEAL
2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a (R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf (R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
3.DRAIN ENGINE COOLANT
for 1GR-FE:
Click hereEngine / Hybrid System>1GR-FE (COOLING)>COOLANT>REPLACEMENT
for 2TR-FE:
Click hereEngine / Hybrid System>2TR-FE (COOLING)>COOLANT>REPLACEMENT
for 5L-E:
Click hereEngine / Hybrid System>5L-E (COOLING)>COOLANT>REPLACEMENT
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (COOLING)>COOLANT>REPLACEMENT
4. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
88710C
6.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Bolt Joint Type)
Remove the 2 bolts.
| *a | Disconnect tube by hand |
Disconnect the air conditioning tube and accessory assembly.
Do not use a screwdriver or similar tool to disconnect the tube.
Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.
Remove the grommet.
Remove the 2 O-rings from the air conditioning tube and accessory assembly.
88710C
7.DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY (for Quick Joint Type)
Using SST, remove the piping clamp.
| *a | SST |
Attach SST to the piping clamp.
Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.
| *a | Push |
| *b | Pull |
| *c | SST |
| *d | Release Lever |
Push down SST and release the clamp lock.
Be careful not to deform the tubes when pushing SST.
Pull SST slightly and push the release lever, then remove the piping clamp with SST.
Remove the piping clamp from SST.
Disconnect the air conditioning tube and accessory assembly.
Cap the open fittings immediately to keep moisture or dirt out of the system.
Remove the grommet.
87245A
8.DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE
Using pliers, grip the claws of the clips and slide the 2 clips.
| *A | for 1GR-FE, Single Air Conditioning System Type A | *B | for 1GR-FE, Dual Air Conditioning System Type A |
| *C | for 1GR-FE, Single Air Conditioning System Type B | *D | for 1GR-FE, Dual Air Conditioning System Type B |
| *E | for 5L-E, Single Air Conditioning System | *F | for 5L-E, Dual Air Conditioning System |
| *G | for 2TR-FE, Single Air Conditioning System | *H | for 2TR-FE, Dual Air Conditioning System |
| *I | for 1GD-FTV, Single Air Conditioning System | *J | for 1GD-FTV, Dual Air Conditioning System |
| *K | for 1GD-FTV, Single Air Conditioning System
w/ Combustion Type Power Heater |
*L | for 1GD-FTV, Dual Air Conditioning System
w/ Combustion Type Power Heater |
Disconnect the 2 heater water hoses.
85110
9.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
10.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
45250
11.REMOVE STEERING COLUMN ASSEMBLY
for Power Tilt and Power Telescopic Steering Column:
for Manual Tilt and Manual Telescopic Steering Column:
12.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
for Walk in Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL
13.REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
for Walk in Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Walk in Seat Type)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL
58510D
14.REMOVE FRONT FLOOR CARPET ASSEMBLY
It is not necessary to fully remove the floor carpet assembly. Partially remove it so that the rear air duct can be removed in a later step.
87212G
15.REMOVE REAR NO. 3 AIR DUCT
Detach the 3 clamps and 6 claws and remove the rear No. 3 air duct.
87212
16.REMOVE REAR NO. 1 AIR DUCT
Detach the 3 clamps and 6 claws and the rear No. 1 air duct.
58861B
17.REMOVE NO. 1 CONSOLE BOX DUCT
| *A | Automatic Transmission |
| *B | Manual Transmission |
Remove the clip and No. 1 console box duct.
55347A
18.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH
Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket LH.
55347A
19.REMOVE NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH
Remove the 2 nuts, bolt and No. 1 instrument panel brace mounting bracket RH.
87201
20.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY
Detach the 3 claws and No. 1 air duct sub-assembly.
87201B
21.REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Remove the screw.
Detach the 2 claws and remove the No. 2 air duct sub-assembly.
22.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY
Disconnect each clamps and each claws.
Remove each bolts, each nuts and wire harness.
Remove the 6 caps.
Using a T40 "TORX" socket, remove the 6 "TORX" bolts.
Using a 8 mm hexagon wrench, loosen the 3 collars.
Remove the 2 bolts and the instrument panel reinforcement assembly with air conditioning unit assembly.
55330B
23.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
Remove the 5 bolts.
Detach the 2 claws and remove the instrument panel reinforcement assembly.