Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter
Component Mass air flow meter
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake System
Component Intake system
Symptom: Main fault
·

Lack of power (No black smoke): Air filter blockage, Air duct is crushed/leaking

·

Black smoke (No lack of power): Leakage between the turbo and the intake manifold


Data List
·

MAP (inside intake air pressure)

·

Target Booster Pressure

When the accelerator is fully depressed, if the MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.



Turbocharger System
Component Turbocharger system
Main fault
·

Air leak in the turbocharged air passage

·

Turbo motor driver not operating well

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle starting, when heavy load)
(Black smoke is not emitted when racing while vehicle stopped)
Data List MAP (inside intake air pressure), Target Booster Pressure
·

When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

·

With the ignition switch ON or idling, MAP = Atmospheric Pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and the MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure increases 1 kPa each time altitude increases by 100 m, and is also affected by the current weather conditions.


VN Turbo Command
·

0%: Fully open vanes (drive rod contracts)

·

Over 90%: Fully closed (drive rod expands and turbo operates effectively)


Diagnostic Point
·

Using the Active Test "Test the Turbo Charger Step Motor", check the drive rod movement.

·

Check the drive rod movement when the ignition switch is turned from ON to off.



Exhaust System
Component Exhaust system
Main fault Blockage
Symptoms Lack of power (high engine speed, when heavy load)
Data List MAP (inside intake air pressure)
When the accelerator is fully depressed, if the MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt.

Glow System
Component Glow system
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Try to measure the resistance of the glow plug

Battery
Component Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet.
Data List Battery Voltage
When cranking, battery voltage is less than 5 V

Engine - 1
Component Engine
Main fault Damaged, Seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Component Engine
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may loose compression.


Injection Feedback Val
·

If Injection Feedback Val is more than 3 mm3/st, the cylinder may have a fault.



Start System
Component Entry and Start system
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter Signal
·

Ignition switch (STA) operation

ON: Starter is operating

OFF: Starter is not operating



Immobiliser system
Component Engine immobiliser system
Main fault Engine immobiliser system/Problem Symptoms Table (See page (Click here))
Symptoms Engine does not start
Data List Immobiliser Communication
·

ON: Normal

·

OFF: GND short or immobiliser is set


Engine Immobiliser System/Data List (See page (Click here))


b.

Diesel Injection

Fuel Supply Pump
Component Fuel supply pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

At a stable condition (e.g. Idling), Fuel Press is within +/-5000 kPa of "Target Common Rail Pressure".

·

If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa then idling will be rough.


HINT:
·

The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or more, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter
Component Fuel filter
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

At a stable condition (e.g. Idling), the fuel pressure is within +/-5000 kPa of "Target Common Rail Pressure ".

·

If the fuel pressure is 20000 kPa below the target pressure then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa then idling will be rough.


HINT:

The fuel pressure changes at engine starting, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored.

Fuel Injector
Component Fuel injector
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injection Feedback Val is more than 3 mm3/st, the cylinder is not normal. This can be read after idling for 1 minute with the engine warmed up (engine coolant temperature is more than 70°C (158°F)).



Pressure Limiter
Component Pressure limiter
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Injector Driver (EDU)
Component Injector Driver (EDU)
Main fault Circuit fault: The fuel injector does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as fuel injector
Diagnostic Trouble Code When the EDU has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Component Fuel pressure sensor
Main fault Open circuit, Decrease in performance (foreign matters is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped, and check that Fuel Press follows Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure. (However, the value may not deviate even when a malfunction is present).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Component Irregular fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Component EGR system
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Pos.
·

Generally, Actual EGR Valve Pos. = Target EGR Pos. +/-5% (fully closed 0%, fully open 100%)

·

Using EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Pos. (The engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is ON (engine stopped).

·

EGR valve opens to halfway point at idling after engine warmed up.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

Leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 3.5 to 4.5 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (3.5 to 4.5 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Component Diesel throttle system
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. It may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position, Actual Throttle Position #2

0%: Fully open

100%: Fully closed

·

Throttle Motor Duty

Normally operates at 50 +/-20%. If outside the range of 50 +/-40% for a few seconds, the throttle may not be sliding properly.

0%: Open diesel throttle

100%: Close diesel throttle

·

When ignition switch is ON (engine stopped), diesel throttle is fully open. When idling, diesel throttle is at halfway point. When ignition switch is turned from ON to off, temporarily closed fully.





Data List Related to Starting Trouble


NOTICE:

The Data List values in the table are the results of checking one vehicle under a specific condition (engine coolant temperature, intake air temperature, atmosphere pressure etc.). That is why use these values for reference only.


a.

Engine Control

MAP
Data List Judgment of Data List Values Faulty Component Diagnosis Note
MAP
·

When MAP is low, there will be difficulty starting.

·

With ignition switch ON or idling, MAP is nearly equal to Atmosphere Pressure (standard atmospheric pressure = 101 kPa).


When MAP is low, the following conditions are possible:
·

The diesel throttle is nearly fully closed.

·

Intake system blocked (turbocharger system also).

·

Exhaust system blocked.


·

When the ignition switch is ON or the vehicle is idling, MAP (intake manifold absolute pressure) and Atmosphere Pressure are mostly the same (standard atmospheric pressure = 101 kPa).

Above approx. 1500 rpm, the turbo becomes effective, and the pressure becomes higher than atmospheric pressure.

·

Inspect while comparing with "Target Booster Pressure".

·

With the accelerator fully open, if the actual Manifold Absolute Pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 seconds or more, a feeling of insufficient power will occur.


Results of real-vehicle check:
·

Ignition switch ON: 99 kPa

·

Cranking: 99 kPa

·

Idling (warm up the engine): 99 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 113 kPa

·

Driving with the accelerator fully open at 2000 rpm: 143 kPa

·

Driving with the accelerator fully open at 3000 rpm: 209 kPa



MAF
Data List Judgment of Data List Values Faulty Component Diagnosis Note
MAF -
·

MAF meter

·

MAF meter circuit

·

Intake system clogging, leaking

·

Exhaust system clogging

·

Turbocharger sub-assembly

·

Leaking or clogging of turbocharger passages

·

EGR valve does not close


·

Based on the MAF, the ECM controls the fuel injection volume, injection timing, EGR, etc.

·

If the value is always approximately 0 g/sec.:

-

Mass air flow meter power source circuit is open.

-

VG circuit is open or shorted.


·

If the value is always 200 g/sec. or more:

-

EVG circuit is open.



Results of real-vehicle check:
w/ EGR
·

Ignition switch ON: 1.54 g/sec.

·

Cranking: 15 g/sec.

·

Idling (warm up the engine): 9 g/sec. (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 80 g/sec.

·

Driving with the accelerator fully open at 2000 rpm: 110 g/sec.

·

Driving with the accelerator fully open at 3000 rpm: 230 g/sec.


HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake Air
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Intake Air - Intake air temperature sensor.
·

After a long soak, the engine coolant temperature, intake air temperature, and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.


-

Coolant Temp
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Coolant Temp
·

Engine coolant temperature is approximately equal to intake air temperature after leaving overnight. After warm-up: Engine coolant temperature is 70°C (158°F) or more.

·

In cases when the engine coolant temperature output is obviously higher than the actual engine coolant temperature, when it is cold, there will be difficulty starting due to problems with glow plugs or insufficient fuel injection.

·

In cases when the engine coolant temperature sensor output is obviously lower than the actual engine coolant temperature, when it is warm, there will be difficulty starting (black smoke will also occur) due to an excess of injected fuel.


Engine coolant temperature sensor
·

If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.

·

After a long soak, the coolant temperature, intake air temperature, and ambient air temperature are approximately equal.


-

Battery Voltage
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Battery Voltage When cranking, in cases when Battery Voltage becomes less than 5 V, the battery is depleted. Battery If 11 V or less, characteristics of some electrical components change.
Results of real-vehicle check:
·

Ignition switch ON: 12.5 V

·

Cranking (with engine warmed up): 9.0 V

·

Idling (warm up the engine): 13.4 V

·

Running without load (2500 rpm): 13.5 V

·

Driving with the accelerator fully open at 2000 rpm: 13 V

·

Driving with the accelerator fully open at 3000 rpm: 13.2 V



Starter Signal
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Starter Signal Operation of ignition switch (STA)
ON: Starter is operating
OFF: Starter is not operating
Entry and Start system
·

Ignition switch (STA) output:

-

ON: Starter is operating

-

OFF: Starter is not operating



-

Engine Speed of Cyl #1 (to #8)
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Engine Speed of Cyl #1 (to #8) When cranking, the engine speed of each cylinder is the same under normal conditions. When a cylinder is approximately 100 rpm higher than the other cylinders, it is conceivable that the compression of that cylinder is being lost.
HINT:

This data is output only when the Active Test "Check the Cylinder Compression" is performed.


-
·

Output only when the Active Test "Check the Cylinder Compression" is performed.

·

With this Active Test, the fuel injection is stopped.

·

Indicates the speed of each cylinder when cranking.

Example - Normal: "Engine speed" of all cylinders is approximately equal.

No. 1 cylinder compression low: "Engine speed of Cyl#1" = approximately 300 rpm, "Engine speed of Cyl #2 to #8 cylinder" = approximately 200 rpm.


-

Immobiliser Communication
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Immobiliser Communication Engine immobiliser system/Data List (See page (Click here)) Engine immobiliser system/Problem Symptoms Table (See page (Click here)) When there is a malfunction in the immobiliser system, a DTC is stored (See page (Click here))
-


b.

Diesel Injection

Target Common Rail Pressure
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Target Common Rail Pressure - -
·

Inspect the (actual) fuel pressure, comparing it against the common rail target value.

·

Considered normal when the actual fuel pressure is within +/-5000 kPa of the target fuel pressure under stable conditions.


Results of real-vehicle check:
·

Ignition switch ON: 32000 kPa

·

Cranking: 29000 kPa

·

Idling (warm up the engine): 32000 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 62000 kPa

·

Running without load (3500 rpm): 80200 kPa

·

Driving with the accelerator fully open at 2000 rpm: 95000 kPa

·

Driving with the accelerator fully open at 3000 rpm: 155000 kPa



Fuel Press
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Fuel Press
·

In a stable operating condition (e.g. idling), Fuel Press is Target Common Rail Pressure +/-5000 kPa.

·

During cranking, if Fuel Press is lower than 25000 kPa, there may be difficulty starting. (Take care as there is a response lag when the pressure rises).

·

When Fuel Press is lower than 25000 kPa, rough idling will occur.


·

If there is a fault with the fuel supply pump (lack of discharge quantity) or pressure limiter (will not fully close), the fuel pressure will drop. Also, a blocked fuel filter, leakage from fuel pipes, and lack of fuel will also make the fuel pressure drop.

·

If air mixes with the fuel, the fuel pressure will shift away from the target fuel pressure.

·

When there is a fault with the fuel supply pump, there is a possibility of lack of power, engine stall, rough idle and difficulty starting.


·

Fuel press is the actual common rail fuel pressure.

·

Inspect by comparing Fuel Press with Target Common Rail Pressure.

·

The ECM uses Fuel Press for feedback control of Target Fuel Pressure via the supply pump.

The injection amount is determined based on the injection timing and fuel pressure.

Also, the spray pattern is selected based on the fuel pressure.


Results of real-vehicle check:
·

Ignition switch ON: 0 kPa

·

Cranking: 29000 kPa

·

Idling (warm up the engine): 32000 kPa (2 minutes after starting the vehicle)

·

Running without load (2500 rpm): 62000 kPa

·

Driving with the accelerator fully open at 2000 rpm: 92000 kPa

·

Driving with the accelerator fully open at 3000 rpm: 155000 kPa



Target Pump SCV Current
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Target Pump SCV Current Idling after warming up, roughly 923 to 1123 mA. When this value is large, the pump is trying to increase the fuel discharge rate.
·

With this data, component fault not specified, use this data as a reference.

·

If the current is 3000 mA or more, there is a possibility the suction control valve is stuck.


·

ECU-calculated value for the suction control valve actuation target current.


·

Value is large when a high fuel pressure is desired.

·

When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.


Results of real-vehicle check:
·

Ignition switch ON: 0 mA

·

Cranking: 1200 mA

·

Running without load (2500 rpm): 1300 mA

·

Driving with the accelerator fully open at 2000 rpm: 1440 mA

·

Driving with the accelerator fully open at 3000 rpm: 1560 mA



Injection Feedback Val #1 (to #8)
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Injection Feedback Val #1 (to #8)
·

When idling after the engine is warmed up, the fuel quantity of each fuel injector is corrected to make each cylinder engine speed equal.

·

Cylinders more than 3 mm3/st may have a fault.


HINT:

Read the value after one minute of idling after warm up (engine coolant temperature above 70°C (158°F)). This value is only calculated when idling.


·

Fault with a fuel injector or lack of compression of a cylinder with a large Injection Feedback Val.

·

Do a compression Active Test. If there is a cylinder that is around 100 rpm more than the other cylinder, there is a possibility that the compression of that cylinder is being lost.

·

If all the cylinder speeds are even according to the compression Active Test result, then the fuel injector of the cylinder may have a fault.

·

With fuel injector faults, other than difficulty starting, there is a possibility of rough idling, lack of power, black smoke, white smoke and knocking.


·

When idling after warm up, the injection amount for each cylinder is corrected to optimize the difference of each cylinder engine speed.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown or insufficient compression is causing poor combustion.


-

Injection Volume
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Injection Volume - - After warming up the engine, when Injection Volume during idling is 10 mm3/st or more, there is tendency for the injector to clog.
Results of real-vehicle check:
·

Cranking: 21 mm3/st (Note: Varies depending on coolant temperature)

·

Idling (warm up the engine): 6 mm3/st

·

Running without load (2500 rpm): 9 mm3/st

·

Running without load (4700 rpm): 16 mm3/st

·

Driving with the accelerator fully open at 2000 rpm: 50 mm3/st

·

Driving with the accelerator fully open at 3000 rpm: 70 mm3/st




c.

Diesel Throttle

Actual Throttle Position, Actual Throttle Position #2
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Actual Throttle Position
Actual Throttle Position #2
·

When the ignition switch is turned to ON (engine stopped), the diesel throttle is fully open. When the ignition switch is turned from ON to off, the diesel throttle will be fully closed temporarily.

·

With the diesel throttle stuck almost fully closed, there is a possibility of rough idling, engine stall, black smoke, difficulty starting and lack of power.


Diesel throttle body Actual Throttle Position is the closing percentage of the throttle valve.
·

Fully closed: 100%

·

Fully open: 0%

HINT:

There is no connection with the accelerator. However, under full load, the throttle is usually fully open (0%).



Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 0%

·

Idling (warm up the engine): 84%

·

Running without load (2500 rpm): 32%

·

Driving with the accelerator fully open at 2000 rpm: 0%

·

Driving with the accelerator fully open at 3000 rpm: 0%



Throttle Motor Duty #1, Throttle Motor Duty #2
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Throttle Motor Duty #1
Throttle Motor Duty #2
·

Normally operates at 50 +/-20%.

·

If 50 +/-40% continues for a few seconds, it is conceivable that the throttle valve is not sliding properly.

-

0%: Drive throttle to open side

-

100%: Drive throttle to closed side



-
·

When this value is large but the actual opening angle does not move smoothly, there is an unable to close malfunction.

·

If this value is small but the actual opening angle does not move smoothly, there is an unable to open malfunction.

·

Usually this value is at approx. 50 +/-20%, but momentary jumps outside this range do occur.

·

If a duty is outside 50 +/-40% for several seconds, it will be judged that the diesel throttle does not move properly and the MIL will be illuminated.


Results of real-vehicle check:
·

Ignition switch ON: 61.5%

·

Cranking: 63%

·

Idling (warm up the engine): 37%

·

Running without load (2500 rpm): 53%

·

Driving with the accelerator fully open at 2000 rpm: 62.5%

·

Driving with the accelerator fully open at 3000 rpm: 64%




d.

Diesel EGR

Target EGR Valve Pos., Target EGR Valve Pos. #2
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Target EGR Valve Pos.
Target EGR Valve Pos. #2
- -
·

Fully open: 100%

·

Fully closed: 0%

·

Used for comparison to "Actual EGR Valve Pos".


Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 0%

·

Idling (warm up the engine): 43%

·

Running without load (2500 rpm): 22%

·

Driving with the accelerator fully open at 2000 rpm: 0%

·

Driving with the accelerator fully open at 3000 rpm: 0%



Actual EGR Valve Pos., Actual EGR Valve Pos. #2
Data List Judgment of Data List Values Faulty Component Diagnosis Note
Actual EGR Valve Pos.
Actual EGR Valve Pos. #2
·

Generally Actual EGR Valve Pos. = Target EGR Pos. (Fully closed = 0%, Fully open = 100%)

·

The EGR valve Active Test can be used to check whether the Actual EGR Valve Pos. = Target EGR Pos.


EGR valve assembly
·

Inspect while comparing to "Target EGR Valve Pos.".

·

Sometimes the malfunction only occurs around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.


Results of real-vehicle check:
·

Ignition switch ON: 0%

·

Cranking: 0%

·

Idling (warm up the engine): 84%

·

Running without load (2500 rpm): 34%

·

Driving with the accelerator fully open at 2000 rpm: 0%

·

Driving with the accelerator fully open at 3000 rpm: 0%



EGR Close Lrn. Status
Data List Judgment of Data List Values Faulty Component Diagnosis Note
EGR Close Lrn. Status
·

"OK" means the fully closed position learning has completed normally.

·

When NG, the learned fully closed position may be outside of the normal range.


- After disconnecting and reconnecting the battery cable, if the ignition switch has not been turned off once, learning may not be completed.
-

EGR Close Lrn. Val.
Data List Judgment of Data List Values Faulty Component Diagnosis Note
EGR Close Lrn. Val. Leave the vehicle idling, with the EGR Close Lrn. Status OK, the normal range of EGR Close Lrn. Val. is within 3.5 to 4.5 V. In cases when EGR Close Lrn. Status is NG or EGR Close Lrn. Val. is at the maximum or minimum (3.5 to 4.5 V) of normal range, it is possible that the EGR valve is not completely closed or a foreign object is lodged in the EGR valve seat area. -
·

This value is the EGR position sensor output voltage.

·

As the maximum and minimum settings are 3.5 V and 4.5 V, if the value becomes stuck at either of these, there is a malfunction in the lift sensor or the valve position is shifted (due to foreign matter, etc.).


-



Actual Examples of Malfunction


HINT:
·

The purpose of the following examples is help you to understand the relationship between each data list item when a certain malfunction occurs. Understanding this relationship helps you to find the real root cause easier.

·

The following are examples of actual malfunctions of a common rail diesel engine.

·

Use them for reference when diagnosing malfunctions.

·

These are not data from the Land Cruiser 1VD-FTV



a.

Fuel is not being supplied to supply pump (Low pressure fuel line clogged)

A371566E01
0.969,1.094 1.208,1.292 0.24,0.198 10 true *2 5.156,0.792 5.385,0.99 0.229,0.198 10 false *1 4.135,3.542 5.198,3.917 1.063,0.375 10 true No fuel pressure 0.573,5.313 7.021,5.521 6.448,0.208 10 false When fuel is not being supplied to the fuel supply pump (low pressure side), Fuel Press is extremely low. 0.396,5.813 0.854,6.01 0.458,0.198 10 false HINT: 0.396,6.167 2.229,6.365 1.833,0.198 10 false *1: Engine is being cranked 0.396,6.531 2.521,6.729 2.125,0.198 10 false *2: ECM does not send IJT signal 0.396,6.906 4.146,7.094 3.75,0.188 10 false - All Data List items are OK, but Fuel Press remains 0 kPa. 0.396,7.313 6.75,7.729 6.354,0.417 10 false - As long as the fuel pressure remains below 10000 kPa, the ECM stops sending IJT signals to the EDU and that is why actual injection duration remains 0 μ seconds. 1.146,8.094 3.271,8.292 2.125,0.198 10 false Areas that need to be inspected: 1.135,8.406 6.729,8.615 5.594,0.208 10 false Check the fuel line from the tank to the fuel filter and from the filter to the fuel supply pump.


b.

Fuel is not being injected (Injectors are leaking)

A183884E14
0.406,6.76 6.25,6.958 5.844,0.198 10 false - All Data List items are OK but Fuel Press does not increase or increases very slowly. 0.406,7.146 6.917,7.521 6.51,0.375 10 false - As long as the fuel pressure remains below 10000 kPa, the ECM stops sending IJT signals to the EDU. From the moment fuel pressure exceeds 25000 kPa, fuel injection will take place and the engine starts. 0.406,5.406 0.813,5.552 0.406,0.146 10 false HINT: 0.323,8.354 6.292,8.542 5.969,0.188 10 false - One or more injectors are leaking and fuel returns via the leakage pipe to the tank. 0.323,7.958 2.5,8.146 2.177,0.188 10 false Areas that may be malfunctioning: 5.406,0.74 5.625,0.938 0.219,0.198 10 true *1 4.667,2 4.885,2.188 0.219,0.188 10 true *3 0.406,6.052 1.448,6.208 1.042,0.156 10 false *2: 0.5 seconds 3.771,1.771 3.99,1.969 0.219,0.198 10 true *2 0.406,6.396 2.521,6.604 2.115,0.208 10 false *3: Pressure is increasing slowly 0.406,5.698 2.333,5.854 1.927,0.156 10 false *1: Engine is running unstabie


c.

Fuel is not being injected (EDU circuit malfunction)

A385286E01
0.594,0.167 6.042,0.563 5.448,0.396 10 false When the EDU circuit malfunctions (e.g. EDU relay or fuse malfunction) and fuel injection stops, Fuel Press becomes much larger than Target Common Rail Pressure 1.344,3.115 2.833,3.323 1.49,0.208 10 false ECM sends IJT signal 0.417,5.792 0.865,6 0.448,0.208 10 false HINT: 0.417,6.125 2.688,6.333 2.271,0.208 10 false - All Data List items are OK. 0.417,6.5 6.5,6.75 6.083,0.25 10 false - If Fuel Press exceeds the target value, this indicates that the fuel supply pump operates properly. 0.417,6.875 6.917,7.083 6.5,0.208 10 false - Pilot 1 and 2 Injection and Main Injection signals confirm that the ECM sends IJT signals to the EDU. 0.417,7.25 2.688,7.458 2.271,0.208 10 false - No injection → No fuel smell 0.396,7.625 2.667,7.833 2.271,0.208 10 false Areas that need to be inspected: 0.396,8.375 2.667,8.583 2.271,0.208 10 false - Check the fuel injectors. 0.417,8 4.333,8.25 3.917,0.25 10 false - Check EDU circuits (power source, IJT, IJF signal circuit).


d.

Fuel supply pump malfunction (Suction control valve momentary sticking)

A371567E02
4.094,4.031 5.229,4.417 1.135,0.385 1.354,0.125 4.917,0.521 3.563,0.396 10 false When Target Pump SCV Current is 3000 mA or more, the suction control valve plunger may be stuck 1.802,1.302 2.042,1.5 0.24,0.198 10 true *1 2.542,2.125 2.781,2.323 0.24,0.198 10 true *2 3.74,4.563 3.979,4.76 0.24,0.198 10 true *3 4.146,4.052 5.156,4.24 1.01,0.188 10 false End of Cranking 0.323,5.594 0.823,5.792 0.5,0.198 10 false HINT: 0.281,5.917 1.667,6.115 1.385,0.198 10 false *1: Start of cranking 0.292,6.24 6.115,6.448 5.823,0.208 10 false *2: In order to reach Target Common Rail Pressure high current is applied to the SCV valve 0.292,6.625 7.01,7.031 6.719,0.406 10 false *3: After cranking has finished, common rail pressure drops below 25000 kPa (despite the high SCV current). This pressure is insufficient to open the injectors and that is why ECM stops injecting and engine finally stalls 0.25,7.469 6.667,7.854 6.417,0.385 10 false - When the suction control valve is stuck, Fuel Press increases slowly during cranking, and the difference between Target Common Rail Pressure and Fuel Press remains large. 0.25,8.135 6.563,8.49 6.313,0.354 10 false In order for Fuel Press to reach the Target Common Rail Pressure value, the ECM must increase Target Pump SCV Current.


e.

Increased opening delay of injectors (Internal contamination)

A183889E02
0.273,6.767 6.871,7.291 6.598,0.524 10 - If the fuel injectors are contaminated, the response of the internal moving parts (plunger, command piston and nozzle) will be delayed. Such a delayed response results in an insufficient amount of fuel being injected. Once the engine has started, this problem usually causes irregular idling and loud knocking. 0.195,5.689 0.636,5.884 0.441,0.195 10 HINT: 0.273,6.007 5.880,6.361 5.608,0.354 10 - If a fuel injector has internal contamination, the engine will not run smoothly. At this time, Injection Feedback Val # of the corresponding cylinder is 3 mm3/st or more. 0.541,8.163 6.350,8.514 5.809,0.351 10 Determine the malfunctioning injector(s) by using Control the Cylinder # Fuel Cut and replace the malfunctioning fuel injector. 0.555,7.869 1.822,8.053 1.267,0.184 10 Inspection method:



CAUTION / NOTICE / HINT

Explanation of Symptom



Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated with compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is leaking, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the fuel injector is open.

Trouble Area Chart According to Problem Cause



A189905E01
0.828,8.536 1.014,8.704 0.185,0.169 10 A 3.632,0.984 5.243,1.167 1.611,0.184 10 Depleted battery 0.235,0.149 1.266,0.333 1.031,0.184 10 Difficult to start 0.853,0.958 2.239,1.129 1.386,0.171 10 Does not crank at all 0.76,4.132 2.390,4.324 1.630,0.192 10 Cranking speed too slow 0.778,5.625 2.799,5.814 2.022,0.188 10 Difficult to start (cranking is OK) 3.616,1.728 6.043,1.936 2.428,0.208 10 ECM power supply circuit malfunction 3.616,2.516 5.571,2.714 1.956,0.198 10 Clutch start switch malfunction 3.586,3.3 6.254,3.482 2.669,0.182 10 Immobilizer System or Smart System fault 3.627,4.122 4.891,4.306 1.263,0.184 10 Depleted battery 4.181,6.554 6.457,6.738 2.276,0.184 10 Fuel is not supplied to supply pump 1.703,6.553 3.033,6.724 1.330,0.171 10 Fuel pressure is low 4.164,7.322 6.075,7.530 1.911,0.208 10 Fuel supply pump malfunction 4.164,8.103 5.769,8.300 1.605,0.198 10 Common rail malfunction 3.57,4.884 6.309,5.241 2.739,0.357 10 Increased internal friction of the engine mechanical parts (too thick oil, seizure,etc.)

A183464E01
0.843,0.089 1.004,0.258 0.161,0.169 10 A 4.189,0.727 5.708,0.910 1.519,0.184 10 EDU circuit malfunction 1.761,0.722 3.119,0.893 1.358,0.171 10 Fuel pressure is high 4.172,1.495 5.062,1.703 0.890,0.208 10 Air in injector 4.203,2.35 5.814,2.533 1.611,0.184 10 Fuel injector malfunction 1.775,2.333 3.161,2.536 1.386,0.203 10 Specific cylinder fault 4.186,3.106 5.928,3.314 1.742,0.208 10 Low compression pressure 4.189,3.973 5.819,4.157 1.630,0.184 10 Glow system malfunction 1.761,3.944 3.403,4.147 1.642,0.203 10 Difficult to start when cold 4.172,4.717 6.401,5.066 2.229,0.349 10 Engine coolant temperature sensor malfunction 1.761,6.093 2.851,6.296 1.090,0.203 10 Poor fuel quality

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing the fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.



PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result
Result Proceed to
Does not crank at all. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Cranking is OK. C



A

2.CHECK BATTERY CONDITION

B

C

8.CHECK INITIALIZATION (FUEL SUPPLY PUMP)
2.CHECK BATTERY CONDITION

OK

3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM

NG

REPLACE BATTERY

3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a tester that is able to communicate with other vehicles.


OK:

Communication is possible (Vehicle can be recognized).




OK

4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)

NG

4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH)
HINT:

This inspection is not necessary for A/T vehicles.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Clutch Switch.


d.

Read the value displayed on the tester.


Standard Value:
Tester Display Condition Specified Condition
Clutch Switch Clutch pedal depressed ON


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

5.READ ALL OUTPUT DTCS

B

REPLACE CLUTCH START SWITCH (for LHD)

C

REPLACE CLUTCH START SWITCH (for RHD)

5.READ ALL OUTPUT DTCS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Utility / All Codes.

Result
Result Proceed to
No DTC is output A
DTCs related to engine are output B



A

6.INSPECT SMART START SYSTEM (IN CASE OF VEHICLES EQUIPPED WITH SMART ENTRY AND START SYSTEM)

B

GO TO RELATED DTC

6.INSPECT SMART START SYSTEM (IN CASE OF VEHICLES EQUIPPED WITH SMART ENTRY AND START SYSTEM)

Check if the "Door Control Transmitter" functions of each key functions properly.

HINT:
·

Check if the engine starts properly with another key.

·

If the doors can not be opened/closed by using the "Door Control Transmitter" function of the key, the battery inside the key may be depleted. In such a case the engine can not be started by pushing the ENGINE START/STOP button.

·

When the door control transmitter battery is depleted, the engine can only be started by holding the door control transmitter against the ENGINE START/STOP button.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If any component installed, remove them and perform the operation check.

Near broadcasting stations, large screens, airports, transformer stations, gasoline stations, etc., the door control transmitter may not operate due to electric wave interference.




NEXT

7.INSPECT CRANKING HOLDING FUNCTION CIRCUIT
7.INSPECT CRANKING HOLDING FUNCTION CIRCUIT
HINT:

Check that "Starter Signal" in the Data List changes to ON when the engine is started.




NEXT

END

8.CHECK INITIALIZATION (FUEL SUPPLY PUMP)

When the engine does not start or another problem such as rough idling is present, perform initialization and check to see if the problem symptoms disappear. If the problem symptoms do not disappear, perform the next procedure.

HINT:

When replacing the ECM, the supply pump initialization must be performed (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).



NEXT

9.READ OUTPUT DTC (RELATED TO ENGINE)
9.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
DTCs related to engine are output B



A

10.TAKE DATA LIST DURING STARTING AND IDLING

B

REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT

10.TAKE DATA LIST DURING STARTING AND IDLING
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data.


d.

Take a snapshot of the following Data Lists with the intelligent tester during "Ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature 70°C (158°F) or more) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Graphs like the ones shown below can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.




A176220E04
2.528,2.211 3.154,2.707 0.626,0.496 10 Snapshot Record Button 2.068,2.715 2.352,2.509 false 2.352,2.509 2.465,2.509 false

Data List
Starter Signal
Engine Speed
Fuel Press
Target Common Rail Pressure
Target Pump SCV Current
Injection Volume
Main Injection Period
Inj. FB Vol. for Idle
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Injection Feedback Val #5
Injection Feedback Val #6
Injection Feedback Val #7
Injection Feedback Val #8
Battery Voltage
Actual EGR Valve Pos.
Actual EGR Valve Pos. #2
Target EGR Pos
Target EGR Pos. #2
Actual Throttle Position
Actual Throttle Position #2
MAF
Target Booster Pressure
MAP

A176219E04
1.054,1.486 1.332,1.633 0.277,0.147 10 ON 1.054,1.952 1.387,2.099 0.333,0.147 10 OFF 3.398,2.139 3.582,2.318 0.185,0.179 10 A 3.398,3.72 3.582,3.899 0.185,0.179 10 A 3.398,5.313 3.582,5.492 0.185,0.179 10 A 3.398,6.846 3.582,7.026 0.185,0.179 10 A 3.398,8.467 3.582,8.646 0.185,0.179 10 A 0.976,2.302 2.281,2.478 1.305,0.175 10 Engine Speed (rpm) 1.231,3.531 1.346,3.677 0.115,0.147 10 0 0.128,0.094 3.433,0.276 3.305,0.183 10 Ignition switch ON, cranking, idling snapshot (1) 1.01,4.19 1.365,4.336 0.355,0.147 10 6000 1.116,8.282 1.352,8.429 0.235,0.147 10 0.0 1.014,2.607 1.347,2.753 0.333,0.147 10 1000 1.071,3.067 1.338,3.213 0.268,0.147 10 500 1.239,5.134 1.354,5.280 0.115,0.146 10 0 1.239,6.691 1.354,6.837 0.115,0.147 10 0 1.017,5.75 1.369,5.896 0.351,0.146 10 6000 1.01,4.672 1.353,4.819 0.343,0.147 10 3000 1.022,6.219 1.366,6.366 0.344,0.146 10 3000 0.901,7.819 1.397,7.966 0.496,0.147 10 1000.0 0.901,7.345 1.397,7.491 0.496,0.147 10 2000.0 0.976,0.761 1.883,0.937 0.907,0.175 10 Starter Signal 3.846,0.658 4.523,0.833 0.677,0.175 10 1 second 0.976,3.889 2.045,4.061 1.069,0.172 10 Fuel Press (kPa) 0.976,5.461 3.267,5.637 2.291,0.175 10 Target Common Rail Pressure (kPa) 0.976,7.075 2.976,7.249 1.999,0.174 10 Target Pump SCV Current (mA)

A181938E04
1.606,0.79 3.364,0.965 1.759,0.176 10 Injection Volume (mm3/st) 1.083,1.569 1.485,1.715 0.401,0.147 10 25.00 3.575,0.913 3.723,1.059 0.149,0.147 10 A 3.575,2.496 3.723,2.642 0.149,0.147 10 A 3.575,4.065 3.723,4.212 0.149,0.147 10 A 3.575,5.683 3.723,5.830 0.149,0.147 10 A 3.575,7.26 3.723,7.407 0.149,0.147 10 A 0.172,0.219 3.416,0.366 3.245,0.147 10 Ignition switch ON, cranking, idling snapshot (2) 1.106,2.698 1.458,2.844 0.351,0.147 10 2000 1.228,5.212 1.464,5.358 0.235,0.147 10 0.0 1.319,3.605 1.434,3.752 0.115,0.146 10 0 1.106,3.168 1.458,3.315 0.351,0.146 10 1000 1.145,4.757 1.446,4.903 0.302,0.147 10 10.0 1.134,2.055 1.493,2.202 0.359,0.147 10 0.00 1.16,4.282 1.467,4.429 0.306,0.147 10 20.0 1.083,1.084 1.485,1.230 0.401,0.147 10 50.00 1.606,2.392 3.253,2.571 1.648,0.179 10 Main Injection Period (μs) 1.606,3.932 2.809,4.106 1.203,0.174 10 Battery Voltage (V) 1.232,6.837 1.468,6.983 0.235,0.147 10 0.0 1.149,6.382 1.450,6.528 0.302,0.147 10 50.0 1.087,5.907 1.470,6.054 0.383,0.147 10 100.0 1.61,5.537 3.736,5.712 2.127,0.174 10 Actual EGR Valve Pos. (%) 1.218,8.387 1.468,8.534 0.250,0.147 10 -20 1.269,7.932 1.451,8.079 0.182,0.147 10 55 1.203,7.458 1.471,7.605 0.268,0.147 10 130 1.61,7.088 3.736,7.262 2.127,0.174 10 Actual Throttle Position (%)

A181939E03
0.14,0.23 3.324,0.433 3.185,0.203 10 Ignition switch ON, cranking, idling snapshot (3) 0.831,1.782 1.212,1.929 0.381,0.147 10 25.00 0.831,1.322 1.296,1.468 0.466,0.147 10 50.00 1.093,2.242 1.208,2.388 0.115,0.146 10 0 1.03,1.022 1.943,1.197 0.914,0.176 10 MAF (gm/sec) 1.014,3.351 1.214,3.498 0.199,0.147 10 65 0.93,2.891 1.215,3.037 0.284,0.147 10 130 1.093,3.811 1.208,3.958 0.115,0.146 10 0 1.03,2.591 1.943,2.766 0.914,0.176 10 MAP (kPa) 3.205,1.093 3.319,1.240 0.114,0.147 10 A 3.201,2.695 3.315,2.841 0.114,0.147 10 A 0.787,4.483 1.257,4.630 0.470,0.147 10 200.00 0.978,5.413 1.283,5.559 0.305,0.146 10 0.00 1.03,4.216 2.961,4.392 1.931,0.176 10 Target Booster Pressure (kPa) 3.206,4.32 3.320,4.467 0.114,0.147 10 A 0.787,4.946 1.257,5.092 0.470,0.147 10 100.00

Reference Values during Engine Start (Point A)
Data List Value Unit
Starter Signal ON -
Engine Speed 524 rpm
Fuel Press 27820 kPa
Target Common Rail Pressure 25000 kPa
Injection Volume 22.71 μs
Main Injection Period 1142 μs
Inj. FB Vol. for Idle -1.33 mm3/st
Battery Voltage 11.0 V
Target EGR Pos.
Target EGR Pos. #2
0 %
Actual EGR Valve Pos.
Actual EGR Valve Pos. #2
0.0 %
Actual Throttle Position
Actual Throttle Position #2
-1 %
MAF 16.45 g/sec
MAP 99 kPa
Target Boost Pressure 100.91 kPa
Coolant Temp 40 °C

Data Condition at Idling (Engine Warmed Up)
Data List Value Unit
Engine Speed 599 rpm
Target Booster Pressure 99.23 kPa
MAP 97 kPa
MAF 8.39 g/sec
Target Common Rail Pressure 32000 kPa
Fuel Press 32100 kPa
Injection Volume 6.13 mm3/st
Actual EGR Valve Pos.
Actual EGR Valve Pos. #2
43.5 %
Actual Throttle Position
Actual Throttle Position #2
84 %
Injection Feedback Val #1 0.0 mm3/st
Injection Feedback Val #2 0.3 mm3/st
Injection Feedback Val #3 0.0 mm3/st
Injection Feedback Val #4 -0.4 mm3/st
Injection Feedback Val #5 -0.4 mm3/st
Injection Feedback Val #6 0.3 mm3/st
Injection Feedback Val #7 0.0 mm3/st
Injection Feedback Val #8 -0.5 mm3/st
Target EGR Pos.
Target EGR Pos. #2
43.5 %
Coolant Temp 78 °C

HINT:

Actual Examples of Malfunction (See "Diagnostic Help" menu)

·

Starting is not possible

-

Fuel is not supplied to supply pump.

Fuel Press: Approximately 1000 kPa or less during cranking.

-

Fuel is not being injected due to EDU circuit malfunction.

Fuel Press: 80000 to 90000 kPa during cranking.

-

Air in injectors.

Fuel Press: 60000 to 70000 kPa during cranking.



·

Cranking time is long

-

Suction control valve is stuck.

Target Pump SCV Current intermittently reaches 3000 mA or more. The suction control valve plunger intermittently becomes stuck. If there is difficult to start when the engine is cold, cool the engine and inspect it.

Injector clogging or internal contamination:

-

Injector clogging or internal contamination:

Injection Feedback Val # of one or more of the cylinders is 3 mm3/st or more.

Injection Feedback Val # can be read when the engine is idling after being warmed up.





NEXT

11.CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE ETC.)
11.CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE ETC.)
a.

Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was starting.

Result
Result Proceed to
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is less than "Target Common Rail Pressure -5000 kPa"
HINT:

As long as the fuel pressure remains below 5000 kPa, the ECM stops sending the injection open signal (IJT) to the EDU, and then the actual injection duration remains 0 microseconds.


A
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is 5000 kPa or more higher than Target Common Rail Pressure B
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is within +/-5000 kPa of Target Common Rail Pressure C

HINT:

Fuel pressure is about 20000 to 35000 kPa when engine cranking and engine coolant temperature 0°C (32°F) or more.

Fuel pressure increases rapidly during cranking.




A

12.BLEED AIR FROM FUEL SYSTEM

B

32.CHECK SNAPSHOT

C

20.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)
12.BLEED AIR FROM FUEL SYSTEM
a.
A175110

Using the hand pump as indicated by the arrow in the illustration, bleed air from the fuel system. Continue pumping until pumping becomes difficult.

HINT:

When the fuel pressure during cranking is extremely low (1000 kPa or less), it is possible that fuel is not being supplied to the supply pump.




NEXT

13.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
13.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
a.

Disconnect the inlet hose from the fuel supply pump.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.



HINT:
·

When lack on fuel, fuel pressure drops.

·

Inspect for fuel filter clogging.

(Check that the fuel filter is not clogged)




OK

14.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)

14.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.

A385062E01
4.104,0.875 4.552,1.146 0.448,0.271 4.844,0.865 5.292,1.135 0.448,0.271 1.646,0.979 2.094,1.25 0.448,0.271 1.5,2.146 1.75,1.802 true 2.271,2.135 1.969,1.813 true 4.938,2.281 5.188,1.938 true 5.604,2.313 5.271,1.938 true 0.635,0.094 2.979,0.448 2.344,0.354 10 false Front view of wire harness connector: (to Suction Control Valve) 3.76,0.094 6.104,0.448 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 1.74,1.031 2.135,1.24 0.396,0.208 10 false z64 4.188,0.927 4.583,1.135 0.396,0.208 10 false C45 4.938,0.917 5.333,1.125 0.396,0.208 10 false C46 4.583,0.729 4.844,0.927 0.26,0.198 10 false *1 5.313,0.74 5.573,0.938 0.26,0.198 10 false *2 1.323,2.188 1.719,2.396 0.396,0.208 10 false +B 2.219,2.156 2.615,2.365 0.396,0.208 10 false PCV 4.344,2.323 5.125,2.531 0.781,0.208 10 false 105 (PCV-) 5.365,2.333 6.208,2.542 0.844,0.208 10 false 106 (PCV+) 0.188,2.063 0.969,2.271 0.781,0.208 10 false *1: for LHD 0.188,2.385 0.969,2.594 0.781,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C45-106 (PCV+) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C46-106 (PCV+) Always Below 1 Ω


Standard Resistance (Check for short):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C45-106 (PCV+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C46-106 (PCV+) - Body ground Always 10 kΩ or higher




OK

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the difficulty starting has been successfully repaired by starting the engine.

HINT:

Fuel pressure during cranking is within +/-5000 kPa of target fuel pressure.


OK:

Malfunction has been repaired successfully.




OK

END

NG

16.CHECK FUEL LEAK (FUEL SUPPLY PUMP)
16.CHECK FUEL LEAK (FUEL SUPPLY PUMP)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Pinch the supply pump return hose and check that Fuel Press during cranking increases.

A181952E03
5.438,0.635 5.625,0.344 5.625,0.344 5.802,0.344 false 5.771,5.927 5.688,6.125 5.688,6.125 5.563,6.125 false 5.333,3.104 5.229,2.885 5.229,2.885 5.125,2.885 false 0.313,0.313 1.99,0.531 1.677,0.219 10 false Possibility of leaking here 5.51,4.417 6.417,4.802 0.906,0.385 10 false Possibility of leaking here 4.844,6.385 6.625,6.604 1.781,0.219 10 false Possibility of leaking here 3.406,0.635 5.052,0.802 1.646,0.167 10 false Common Rail (for Bank 1) 3.406,5.625 5.125,5.823 1.719,0.198 10 false Common Rail (for Bank 2) 5.865,0.229 6.813,0.604 0.948,0.375 10 false Fuel Pressure Sensor 5.229,1.948 6.146,2.156 0.917,0.208 10 false Fuel Cooler*2 2.823,3.427 3.74,3.604 0.917,0.177 10 false Fuel Cooler*1 2.01,4.083 2.719,4.281 0.708,0.198 10 false Fuel Filter 2.083,5.302 2.76,5.469 0.677,0.167 10 false Fuel Tank 4.281,2.792 5.115,2.979 0.833,0.188 10 false Fuel Injector 4.5,6.01 5.573,6.188 1.073,0.177 10 false Pressure Limiter 0.5,3 1.698,3.188 1.198,0.188 10 false Fuel Supply Pump 0.229,4.313 1.646,4.51 1.417,0.198 10 false *1: Air-cooled Type 0.229,4.688 1.719,4.917 1.49,0.229 10 false *2: Water-cooled Type 0.688,6.448 1.958,6.635 1.271,0.188 10 false High Pressure Fuel 0.688,6.917 1.958,7.104 1.271,0.188 10 false Return Fuel 0.688,7.365 1.958,7.552 1.271,0.188 10 false Suction Fuel

Result
Result Proceed to
Fuel Press increases A
No change B



B

17.CHECK FUEL LEAK (PRESSURE LIMITER (COMMON RAIL (for Bank 2))

A

17.CHECK FUEL LEAK (PRESSURE LIMITER (COMMON RAIL (for Bank 2))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Pinch the pressure limiter return hose and check that Fuel Press during cranking increases.

Result
Result Proceed to
Fuel Press increases A
No change B



B

18.REPLACE FUEL SUPPLY PUMP

A

REPLACE COMMON RAIL (for Bank 2)

18.REPLACE FUEL SUPPLY PUMP
a.


NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the difficulty starting has been successfully repaired by starting the engine.

HINT:

Fuel pressure during cranking is within +/-5000 kPa of target fuel pressure.




NEXT

END

20.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT)
a.

Check Target Pump SCV Current in the snapshot taken when the engine was starting.

Result:
Result Proceed to
Target Pump SCV Current is 3000 mA or more A
Target Pump SCV Current is less than 3000 mA B




B

21.CHECK DATA LIST

A

21.CHECK DATA LIST
a.

Check Injection Feedback Val # and Injection Volume in the snapshot taken when the engine was idling.

Result:
Result Proceed to
Injection Feedback Val #1 to #8 is outside the range of +/-3 mm3/st
HINT:

There may be malfunction in the corresponding cylinder.


A
Injection Feedback Val #1 to #8 is within the range of +/-3 mm3/st and Injection Volume is more than 10 mm3/st B*
Injection Feedback Val #1 to #8 is within the range +/-3 mm3/st and Injection Volume is 10 mm3/st or less C


HINT:

*: When case "B" occurs usually symptoms may be noticeable, such as difficult starting, rough idling, knocking or black smoke at high common rail pressure.




A

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

REPLACE FUEL INJECTORS OF ALL CYLINDERS

C

26.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Cylinder #1 to #8 Fuel Cut.


HINT:
·

If the engine idle speed does not change when a fuel injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




NEXT

23.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
23.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #8.


d.

Check the engine speed during the Active Test.

OK:

If the values of Engine Speed Cyl #1 to #8 are within +/-10 rpm of each other.


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a loss of compression in that cylinder.




OK

25.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

NG

24.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
24.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the Active Test "Check the Cylinder Compression".


a.

Check the cylinder compression pressure (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

25.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

25.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER
HINT:

The injector is determined to be faulty as the corresponding cylinder is malfunctioning, but has no compression loss.



NEXT

END

26.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.


Result
Result Proceed to
Difficult to start only for cold engine. A
Difficult to start both for cold and warmed up engine. B


A

27.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

30.CHECK FUEL QUALITY
27.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.


OK

28.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

28.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
A163041E02
1.354,2.927 1.688,2.896 false 1.677,2.896 1.719,2.896 false 1.75,2.802 2.958,3.031 1.208,0.229 10 true Screw Grommet

a.

Disconnect the glow plug connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Glow plug terminal - Body ground 20°C (68°F) Approximately 1 Ω


HINT:

If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.


NOTICE:
·

Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit or shorten the life of the glow plugs.

·

Keep the glow plugs free of oil and fuel while cleaning.

·

Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.

·

Do not apply more than 11 V to the glow plugs as it may cause an open circuit.





OK

29.INSPECT INJECTOR COMPENSATION CODE

NG

29.INSPECT INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).

OK:

Compensation codes stored in the ECM match compensation codes of the installed fuel injectors.




OK

30.CHECK FUEL QUALITY

NG

PERFORM REGISTRATION FUEL INJECTOR COMPENSATION CODE

30.CHECK FUEL QUALITY
a.

Check that fuel with cetane number is used.



NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the difficulty starting has been successfully repaired by starting the engine.



NEXT

END

32.CHECK SNAPSHOT
HINT:

When all Data List values are OK and Fuel Press is higher than Target Common Rail Pressure, perform the following inspection.



NEXT

33.INSPECT INJECTOR DRIVER (EDU POWER SOURCE)
33.INSPECT INJECTOR DRIVER (EDU POWER SOURCE)
U162835E02
1.083,1.5 0.896,1.75 false 2.333,3.448 2.521,3.719 false 0.323,0.917 0.615,1.083 0.292,0.167 10 false C73 0.677,0.76 0.854,0.906 0.177,0.146 10 false *1 0.344,1.219 0.667,1.417 0.323,0.198 10 false C75 0.677,1.063 0.854,1.208 0.177,0.146 10 false *2 0.344,2.708 0.635,2.875 0.292,0.167 10 false C74 0.677,2.563 0.854,2.708 0.177,0.146 10 false *1 0.229,3.958 0.844,4.135 0.615,0.177 10 false *1: No. 1 0.229,4.281 0.844,4.458 0.615,0.177 10 false *2: No. 2 0.323,3.021 0.646,3.208 0.323,0.188 10 false C76 0.677,2.875 0.854,3.021 0.177,0.146 10 false *2 0.667,1.781 1.042,2.01 0.375,0.229 10 false GND 2.448,3.74 2.823,3.969 0.375,0.229 10 false +B 0.198,0.021 2.583,0.375 2.385,0.354 10 false Front view of wire harness connector: (to EDU)

a.

Disconnect the C73 and C74 No. 1 injector driver (EDU) connectors.


b.

Disconnect the C75 and C76 No. 2 injector driver (EDU) connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
No. 1
Tester Connection Switch Condition Specified Condition
C74-8 (+B) - C73-1 (GND) Ignition switch ON 11 to 14 V


Standard Voltage:
No. 2
Tester Connection Switch Condition Specified Condition
C76-8 (+B) - C75-1 (GND) Ignition switch ON 11 to 14 V




OK

34.INSPECT FUEL INJECTOR

NG

34.INSPECT FUEL INJECTOR
HINT:

If there is no initial combustion during cranking, there may be air in the injectors.



NEXT

END