1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
52119A
4.REMOVE FRONT BUMPER COVER
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>REMOVAL)
53301
5.REMOVE HOOD SUB-ASSEMBLY
Remove the 2 hood support bolts and disconnect the hood supports.
Remove the hood support assembly while supporting the hood by hand.
Remove the 4 bolts and hood.
55781E
6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53737B
7.REMOVE FRONT FENDER APRON SEAL LH
53739A
8.REMOVE FRONT FENDER APRON SEAL REAR LH
53736G
9.REMOVE FRONT FENDER APRON SEAL FRONT RH
53738A
10.REMOVE FRONT FENDER APRON SEAL REAR RH
51405A
11.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Remove the 10 bolts and No. 1 engine under cover.
51442
12.REMOVE NO. 2 ENGINE UNDER COVER
Remove the 2 bolts and No. 2 engine under cover.
51440
13.REMOVE OIL PAN PROTECTOR ASSEMBLY
14.DRAIN ENGINE OIL
15.DRAIN ENGINE COOLANT
32917
16.REMOVE TRANSMISSION OIL COOLER AIR DUCT
53294C
17.REMOVE RADIATOR SIDE DEFLECTOR LH
11209
18.REMOVE V-BANK COVER SUB-ASSEMBLY
Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
| *1 | Bracket |
| *2 | Hook |
| *3 | Pin |
| *4 | Grommet |
17880
19.REMOVE AIR CLEANER HOSE ASSEMBLY
17700
20.REMOVE AIR CLEANER ASSEMBLY
Remove the 3 bolts and air cleaner.
16571C
21.REMOVE NO. 1 RADIATOR HOSE
16572D
22.REMOVE NO. 2 RADIATOR HOSE
16711
23.REMOVE FAN SHROUD
16400
24.REMOVE RADIATOR ASSEMBLY
23801P
25.DISCONNECT FUEL MAIN AND RETURN HOSE
Remove the fuel pipe clamp.
Disconnect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
26.DISCONNECT WIRE HARNESS AND HOSE
Disconnect the purge line hose.
Remove the heater hose.
Disconnect the clamp and ECM connector.
| *A | w/o Rear Heater |
| *B | w/ Rear Heater |
Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>ECM>REMOVAL).
Disconnect the 5 connectors and clip from the connector holder block.
Remove the bolt and disconnect the ground wire.
Remove the nut and disconnect the wire from the positive (+) battery cable.
Disconnect the cable from the positive (+) battery terminal.
Remove the bolt and disconnect the ground wire from the body.
Disconnect the clamp.
Remove the nut and disconnect the wire and 2 clips from the engine room junction block.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
Disconnect the 2 connectors and 2 clamps.
w/ Winch:
Detach the wire harness clamp, remove the nut and disconnect the ground wire from the wire harness clamp bracket.
88320
27.DISCONNECT COOLER COMPRESSOR ASSEMBLY
44310
28.DISCONNECT VANE PUMP ASSEMBLY
27020
29.REMOVE GENERATOR ASSEMBLY
17430
30.REMOVE TAILPIPE ASSEMBLY
17420
31.REMOVE CENTER EXHAUST PIPE ASSEMBLY
17450B
32.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17410
33.REMOVE FRONT EXHAUST PIPE ASSEMBLY
11452
34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Disconnect the wire harness clamp.
Remove the dipstick.
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
37140
35.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110
36.REMOVE REAR PROPELLER SHAFT ASSEMBLY
37117
37.REMOVE PROPELLER SHAFT HEAT INSULATOR
17119
38.REMOVE NO. 2 MANIFOLD STAY
17168
39.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17105
40.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
17118
41.REMOVE NO. 1 MANIFOLD STAY
17167
42.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17104
43.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
28192
44.REMOVE STARTER COVER
28100
45.REMOVE STARTER ASSEMBLY
35000
46.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
12371
47.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Only perform this procedure when replacement of the engine mounting insulator is necessary.
Remove the 2 bolts and front engine mounting insulator RH.
Remove the 4 bolts and rear engine mounting insulator from the transmission.
32101
48.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using SST, hold the crankshaft.
Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.
32907A
49.DISCONNECT OIL COOLER PIPE ASSEMBLY
Remove the 2 bolts and disconnect the oil cooler pipe.
50.REMOVE WATER PIPE AND HOSE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the hose. Then remove the water pipe and hose.
51.REMOVE ENGINE ASSEMBLY
Install 2 engine hangers with 2 bolts as shown in the illustration.
| Engine hanger | 12281-38150 |
| Bolt | 90119-14120 |
Attach an engine sling device and hang the engine with a chain block.
| *1 | Engine Hanger |
| *2 | ENGINE |
| *a | 50° or less |
When hanging the engine, make sure to hang the engine with the sling device's hanging angle at 50° or less. If not, the engine or engine hangers may be damaged.
Remove the 4 engine mounting insulator bolts.
| *A | RH |
| *B | LH |
Lift the engine out from the vehicle slowly and carefully.
Make sure the engine is clear of all wiring, hoses and cables.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
52.INSTALL ENGINE ON ENGINE STAND
Install the engine onto an engine stand with bolts.
Remove the 2 bolts and 2 engine hangers.
12362A
53.REMOVE FRONT ENGINE MOUNTING INSULATOR LH
Remove the nut and mounting insulator.
12361
54.REMOVE FRONT ENGINE MOUNTING INSULATOR RH
Remove the nut and mounting insulator.
12316A
55.REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET LH
Remove the bolt and No. 2 front engine mounting bracket LH.