Home › Engine / Hybrid System › 3UR-FE (LUBRICATION) › OIL PUMP › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052796 3UR-FE LUBRICATION _0255205 OIL PUMP A

3UR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 32917 5.REMOVE TRANSMISSION OIL COOLER AIR DUCT

Hide 53294C 6.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 55781E 7.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53736G 9.REMOVE FRONT FENDER APRON SEAL FRONT RH

Hide 51405C 10.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 16400 17.REMOVE RADIATOR ASSEMBLY

Hide 18.DISCONNECT ENGINE WIRE

a.

Engine Room LH Side:

i.
A370861

Remove the engine room relay block cover.


ii.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


iii.
A361462

Disconnect the injector connector.


iv.

Disconnect the 4 ignition coil connectors.


v.

Disconnect the 2 VVT sensor connectors.


vi.

Disconnect the 4 clamps.


vii.

Remove the bolt and disconnect the ground wire.


viii.

Disconnect the noise filter connector.


ix.
A174202

Disconnect the engine coolant temperature sensor connector.


x.

Disconnect the 2 camshaft timing oil control valve connectors.


xi.

Disconnect the camshaft position sensor connector.


xii.

Disconnect the 3 clamps.


xiii.

Disconnect the cooler compressor connector.



b.
A361463

Engine Room RH Side:

i.

Disconnect the 2 camshaft timing oil control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the injector connector.


iv.

Disconnect the 2 VVT sensor connectors.


v.

Disconnect the noise filter connector.


vi.

Remove the bolt and disconnect the ground wire.


vii.

Disconnect the throttle position sensor and throttle control motor connector.


viii.

Disconnect the 6 clamps.



c.
A174204

Disconnect the 2 clamps and power steering oil pressure switch connector.


Hide 19.DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY

a.
A239168

Disconnect the 3 hoses.


b.

Remove the 2 bolts and disconnect the water pipe and hose from the cylinder head cover.


Hide 88320 20.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A178491

Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.

HINT:

It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



Hide 23902 21.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A165142E12
0.052,0.094 0.323,0.333 0.271,0.24 10 false *A 0.063,2.281 0.427,2.49 0.365,0.208 10 false *B

Remove the 2 bolts and disconnect the fuel tube.

Text in Illustration
*A LH Side
*B RH Side


Hide 11452 23.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 83520 24.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 16207 25.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A165547

Remove the 3 bolts.


b.

Disconnect the 4 hoses and remove the water by-pass pipe.


Hide 44310 29.DISCONNECT VANE PUMP ASSEMBLY

a.
A163289

Remove the 2 bolts and disconnect the vane pump.


Hide 16261G 32.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A237017

Remove the No. 1 water by-pass hose by disconnecting the hose from the water inlet housing and front water by-pass joint.


Hide 16206 33.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A162551

Disconnect the 2 hoses.


b.

Remove the 2 bolts and water by-pass pipe.


Hide 16355 34.REMOVE FRONT WATER BY-PASS JOINT

a.
A162552

Disconnect the No. 2 water by-pass hose from the water by-pass joint.


b.

Remove the 4 nuts, water by-pass joint and 2 gaskets.


Hide 11212 35.REMOVE NO. 2 ENGINE COVER

A237721

Hide 12611 36.REMOVE NO. 1 ENGINE COVER

A237722

Hide 16323 37.REMOVE WATER INLET HOUSING

a.
A162554

Remove the 3 bolts, water inlet housing and gasket.


Hide 16173 38.REMOVE WATER PUMP PULLEY

a.
A162556E05
0.604,1.521 0.604,1.458 false 0.604,1.458 1.052,1.219 false 0.479,1.573 0.813,1.76 0.333,0.188 10 false SST

Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts and water pump pulley.


Hide 16603 39.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A162557

Remove the bolt and idler pulley.


Hide 16211 40.REMOVE FLUID COUPLING BRACKET

a.
A162558

Remove the 4 bolts and fluid coupling bracket.


Hide 16620 41.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.


Hide 19500 42.REMOVE IGNITION COIL ASSEMBLY

a.

Remove the 8 bolts and 8 ignition coils.


Hide 11202 43.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A162523

Remove the 14 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).


Hide 11201 44.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A163381

Remove the bolt and noise filter.


b.
A162525

Remove the 14 bolts, seal washer, cylinder head cover and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



c.
A162526

Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).


Hide 13471 46.REMOVE CRANKSHAFT PULLEY

a.
A164228E11
0.198,0.958 0.198,1.938 true 0.198,1.406 0.438,1.406 true 0.073,1.979 0.396,2.167 0.323,0.188 10 false SST 2.99,1.927 3.302,2.208 0.313,0.281 10 true *a

Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.

SST
09213-70011  
09330-00021  

Text in Illustration
*a Hold
V100135

Turn


b.
A164229E09
0.458,0.625 0.594,0.625 true 0.594,0.625 0.635,1.021 true 0.104,0.531 0.427,0.708 0.323,0.177 10 false SST 2.917,2.417 3.219,2.667 0.302,0.25 10 true *a

Using the pulley set bolt and SST, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05011)

Text in Illustration
*a Hold
V100135

Turn


Hide 47.DISCONNECT WIRE HARNESS CLAMP BRACKET

a.
A163733

Remove the bolt and disconnect the bracket.


Hide 13521A 48.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A163993

Using a screwdriver, remove the timing gear key from the crankshaft.


Hide 11302 49.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A237019

Remove the 28 bolts and nut shown in the illustration.

Text in Illustration
V100135

Bolt
V100136

Nut


b.
A162530

Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.


HINT:

Tape the screwdriver tip before use.



c.
A162531

Remove the oil pump gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan.


Hide 16322 50.REMOVE WATER INLET PIPE

a.
A162532

Remove the water inlet pipe.


b.

Remove the 2 O-rings from the water inlet pipe.