1.INSTALL STUD BOLT
Install the oil pan stud bolt.
Using E6 and E8 "TORX" socket wrenches, install the 6 stud bolts as shown in the illustration.
Install the cylinder head cover LH stud bolt.
Using an E6 "TORX" socket wrench, install the stud bolt as shown in the illustration.
2.INSTALL RING PIN
Using a plastic-faced hammer, tap in new ring pins to the camshaft housing.
2.7 to 3.3 mm (0.106 to 0.130 in.)
| *1 | Protrusion Height | - | - |
| *a | LH | *b | RH |
3.INSTALL STRAIGHT PIN
Using a plastic-faced hammer, tap in new straight pins to the camshaft housing.
| Item | Specified Condition |
|---|---|
| Straight pin A | 7.7 to 8.3 mm (0.303 to 0.327 in.) |
| Straight pin B | 5.7 to 6.3 mm (0.224 to 0.248 in.) |
| *1 | Protrusion Height | - | - |
| *a | LH | *b | RH |
4.INSTALL TAPER SCREW PLUG
Apply adhesive to 2 or 3 threads of the taper screw plug end.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the taper screw plug.
Install the taper screw plug within 3 minutes after applying adhesive.
Do not expose the taper screw plug to coolant within 1 hour of the installation.
11381A
5.INSTALL REAR CRANKSHAFT OIL SEAL
Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear oil seal retainer edge.
Apply MP grease to the lip of the oil seal.
11381
6.INSTALL ENGINE REAR OIL SEAL RETAINER
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil seal retainer or cylinder block.
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2 to 3 mm (0.0787 to 0.118 in.)
| *1 | Seal Packing |
Remove any oil from the contact surfaces.
Install the oil seal retainer within 3 minutes after applying seal packing.
Install the oil seal retainer with the 5 bolts and 2 nuts.
When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.
Do not start the engine for at least 2 hours after installation.
7.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the 2 water jacket spacers as shown in the illustration.
| *1 | UP Mark |
| *2 | L Mark |
| *3 | R Mark |
Make sure that the "L mark", "R mark" and "UP mark" are oriented as shown in the illustration.
89615
8.INSTALL KNOCK CONTROL SENSOR
16332
9.INSTALL NO. 1 WATER OUTLET PIPE
11115
10.INSTALL CYLINDER HEAD GASKET
11101
11.INSTALL CYLINDER HEAD SUB-ASSEMBLY
11116
12.INSTALL NO. 2 CYLINDER HEAD GASKET
11102
13.INSTALL CYLINDER HEAD LH
13716
14.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem caps.
Install the 24 valve stem caps to the cylinder head.
13750
15.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the valve lash adjuster (See page Engine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).
Install the 24 valve lash adjusters to the cylinder head.
Install the lash adjuster at the same place it was removed from.
13801
16.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Apply engine oil to the lash adjuster tips and valve stem cap ends.
Install the 24 valve rocker arms as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
17.INSTALL CAMSHAFT BEARING CAP (for Bank 2)
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the No. 3 camshaft and No. 4 camshaft to the camshaft housing.
Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.
Temporarily install the 8 bolts in the order shown in the illustration.
11104A
18.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
Make sure that the valve rocker arm is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.5 to 4.5 mm (0.138 to 0.177 in.)
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
When installing the camshaft housing sub-assembly LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly LH, clean the installation surfaces and reapply seal packing.
If the camshaft housing sub-assembly LH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
Do not start the engine for at least 2 hours after installing.
Tighten the 8 bolts in the order shown in the illustration.
Thoroughly wipe clean any seal packing.
19.INSTALL CAMSHAFT BEARING CAP (for Bank 1)
Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.
Install the camshaft and No. 2 camshaft to the camshaft housing.
Check the marks and numbers on the camshaft bearing caps and place each of them in the proper position facing the proper direction.
Temporarily install the 8 bearing cap bolts in the order shown in the illustration.
11103C
20.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Lash Adjuster |
| *3 | Valve Stem |
| *4 | Valve Stem Cap |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.5 to 4.5 mm (0.138 to 0.177 in.)
| *1 | Seal Packing |
Remove any oil from the contact surface.
Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.
| *1 | Knock Pin |
| *a | Front View |
When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration.
Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly RH, clean the installation surfaces and reapply seal packing.
If the camshaft housing sub-assembly RH is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.
Do not start the engine for at least 2 hours after installing.
Tighten the 8 bolts in the order shown in the illustration.
Thoroughly wipe clean any seal packing.
13560A
21.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY (for Bank 2)
Install the No. 3 chain tensioner assembly with the bolt.
Push in the tensioner and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
22.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.
Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 3 chain tensioner assembly.
13550
23.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY (for Bank 1)
Install the No. 2 chain tensioner assembly with the bolt.
Push in the No. 2 chain tensioner assembly and insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the tensioner.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
24.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)
Align the mark plates (yellow) with the timing marks of the camshaft timing gear assemblies as shown in the illustration.
| *1 | Timing Mark |
| *2 | Mark Plate |
Apply a light coat of engine oil to the bolt threads and bolt-seating surface.
Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear assembly with the No. 2 chain sub-assembly installed.
Using SST to hold the hexagonal portion of each camshaft, tighten the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.
| *a | Turn |
| *b | Hold |
Remove the pin from the No. 2 chain tensioner assembly.
13561
25.INSTALL NO. 1 CHAIN VIBRATION DAMPER
Install the No. 1 chain vibration damper with the 2 bolts.
13562
26.INSTALL NO. 2 CHAIN VIBRATION DAMPER
Install the 2 No. 2 chain vibration dampers.
13521
27.INSTALL CRANKSHAFT TIMING SPROCKET
Align the key groove of the timing sprocket with the timing sprocket set key.
Install the timing sprocket to the crankshaft with the sprocket facing inward as shown in the illustration.
| *a | Inward |
13581
28.INSTALL NO. 1 IDLE GEAR SHAFT
Apply a light coat of engine oil to the sliding surface of the No. 1 idle gear shaft.
Temporarily install the No. 1 idle gear shaft and No. 1 idle gear with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.
| *1 | Knock Pin |
Make sure that the idle gear is installed facing the proper direction.
Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.
Remove the bar from the chain tensioner.
13506
29.INSTALL CHAIN SUB-ASSEMBLY
Align the mark plate and timing marks as shown in the illustration and install the chain.
| *1 | Mark Plate |
| *2 | Timing Mark |
The camshaft mark plates are orange.
Do not pass the chain around the crankshaft, just temporarily place it on the crankshaft.
Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.
| *1 | Chain Plate |
| *a | When idle sprocket is reused |
| *b | Mark |
| *c | Align |
|
Turn |
When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been when tightening the chain between the banks.
Align the mark plate and timing marks as shown in the illustration and install the chain to the crankshaft timing sprocket.
| *1 | Mark Plate |
| *2 | Timing Mark |
The crankshaft mark plate is yellow.
Temporarily install the pulley set bolt.
Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).
| *1 | Center Line |
| *2 | Timing Mark |
| *3 | Sensor Plate |
13559
30.INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper.
13540
31.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the stopper plate of the tensioner clockwise and push in the plunger of the tensioner as shown in the illustration.
| *1 | Stopper Plate |
| *a | Push |
Turn the stopper plate of the tensioner counterclockwise and insert a pin with a diameter of 1.27 mm (0.0500 in.) into the holes on the stopper plate and tensioner to fix the stopper plate in place.
Install the chain tensioner with the 2 bolts.
Remove the pin from the No. 1 chain tensioner.
32.INSPECT VALVE TIMING
Check the camshaft timing marks.
Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear.
If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
Check that each camshaft timing mark is positioned as shown in the illustration.
| *1 | Timing Mark | - | - |
| *a | Viewpoint | - | - |
for Intake Camshaft:
Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.
If the valve timing is misaligned, reinstall the timing chain.
Remove the pulley set bolt.
16100
33.INSTALL ENGINE WATER PUMP ASSEMBLY
Install a new gasket and the engine water pump with the 8 bolts.
11302
34.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
11301C
35.INSTALL FRONT CRANKSHAFT OIL SEAL
12121
36.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Install the No. 1 oil pan baffle plate with the 6 bolts.
12101
37.INSTALL OIL PAN SUB-ASSEMBLY
15104
38.INSTALL OIL STRAINER SUB-ASSEMBLY
12102A
39.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
12101A
40.INSTALL OIL PAN DRAIN PLUG
Install a new gasket and the drain plug.
89491
41.INSTALL ENGINE OIL LEVEL SENSOR
42.POUR ENGINE OIL
Before installing the cylinder head cover, pour engine oil into the locations shown in the illustration.
11193
43.INSTALL SPARK PLUG TUBE GASKET
Using a cutter knife, cut off the seal part of the removed gasket.
|
Area to cut off |
Using the removed gasket and a hammer, tap in a new gasket until it stops.
| *1 | Removed Gasket |
| *2 | New Gasket |
If the removed gasket does not fit on the new one, correct the removed one with pliers.
Apply a light coat of MP grease to the gasket lip.
Return the ventilation baffle plate claws to their original positions.
11201
44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2 to 3 mm (0.0787 to 0.118 in.)
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the cylinder head cover.
Install the seal washers to the bolts.
Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| A | 25 mm (0.984 in.) |
| B | 35 mm (1.38 in.) |
| C | 65 mm (2.56 in.) |
| D | 60 mm (2.36 in.) |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
Do not start the engine for at least 2 hours after the installation.
11202
45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover or cylinder head cover.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2 to 3 mm (0.0787 to 0.118 in.)
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install 3 new gaskets as shown in the illustration.
Install a new gasket to the cylinder head cover.
Install the seal washers to the bolts.
Temporarily install the cylinder head cover with the 12 bolts. Tighten the bolts uniformly in several steps.
| Item | Length |
|---|---|
| A | 25 mm (0.984 in.) |
| B | 35 mm (1.38 in.) |
| C | 70 mm (2.76 in.) |
| D | 60 mm (2.36 in.) |
|
Bolt A |
|
Bolt B |
|
Bolt C |
|
Bolt D |
Do not start the engine for at least 2 hours after the installation.
13471
46.INSTALL CRANKSHAFT PULLEY
12204
47.INSTALL PCV VALVE SUB-ASSEMBLY
19100P
48.INSTALL SPARK PLUG
16356
49.INSTALL REAR WATER BY-PASS JOINT
Apply soapy water to a new O-ring and install it to the water outlet pipe. Then install 2 new gaskets to the water ports LH and RH.
| *1 | New O-Ring |
| *2 | New Gasket |
Install the rear water by-pass joint with the 2 bolts and 4 nuts.
16323
50.INSTALL WATER INLET HOUSING
15671
51.INSTALL OIL FILTER BRACKET
52.INSTALL OIL FILTER ELEMENT
15772
53.INSTALL NO. 2 OIL PIPE
15771
54.INSTALL NO. 1 OIL PIPE
12185
55.INSTALL OIL FILLER CAP HOUSING
Install a new gasket and the oil filler cap housing with the 2 nuts.
| *1 | New Gasket |
Install the oil filler cap.
15340
56.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 2)
15330B
57.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 2)
15330B
58.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side of Bank 1)
15330B
59.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side of Bank 1)
11401G
60.INSTALL CRANKSHAFT POSITION SENSOR
11301M
61.INSTALL VVT SENSOR (for Exhaust Side of Bank 2)
11301M
62.INSTALL VVT SENSOR (for Intake Side of Bank 2)
11301M
63.INSTALL VVT SENSOR (for Exhaust Side of Bank 1)
11301M
64.INSTALL VVT SENSOR (for Intake Side of Bank 1)
11415
65.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Apply adhesive to 2 or 3 threads of the cylinder block water drain cock end.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
for Type A:
Install the 2 cylinder block water drain cocks.
| *a | LH |
| *b | RH |
| *c | Front |
Install the cylinder block water drain cock within 3 minutes after applying adhesive.
Do not expose the cylinder block water drain cock to coolant within 1 hour of the installation.
Rotate the 2 cylinder block water drain cocks clockwise to the position shown in the illustration.
Do not rotate the cylinder block water drain cock by more than 1 revolution (360°) after tightening the cylinder block water drain cock to the specified torque.
Do not loosen the cylinder block water drain cock after setting it correctly.
Install the 2 cylinder block water drain cock plugs to the 2 cylinder block water drain cocks.
for Type B:
Install the cylinder block water drain cock.
| *a | Front |
Install the cylinder block water drain cock within 3 minutes after applying adhesive.
Do not expose the cylinder block water drain cock to coolant within 1 hour of the installation.
Rotate the cylinder block water drain cock clockwise to the position shown in the illustration.
Do not rotate the cylinder block water drain cock by more than 1 revolution (360°) after tightening the cylinder block water drain cock to the specified torque.
Do not loosen the cylinder block water drain cock after setting it correctly.
Install the cylinder block water drain cock plug to the cylinder block water drain cock.
89422
66.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
83520
67.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY