Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255065 ENGINE UNIT A

1VD-FTV ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block, cylinder head, crankshaft, connecting rod, camshaft and other parts.

·

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.



PROCEDURE

Hide 11102 3.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

a.

Place the cylinder head on the cylinder head gasket.

NOTICE:

Ensure that no oil is on the mounting surface of the cylinder head.



b.

c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
U162894E02
1.74,0.354 1.896,0.521 0.156,0.167 10 false 1 1.75,2.771 1.906,2.938 0.156,0.167 10 false 2 2.375,2.771 2.531,2.938 0.156,0.167 10 false 6 2.323,0.354 2.479,0.521 0.156,0.167 10 false 5 1.135,0.354 1.292,0.521 0.156,0.167 10 false 4 1.104,2.771 1.26,2.938 0.156,0.167 10 false 3 0.5,2.771 0.656,2.938 0.156,0.167 10 false 7 2.917,0.354 3.073,0.521 0.156,0.167 10 false 9 0.531,0.354 0.688,0.521 0.156,0.167 10 false 8 2.927,2.771 3.115,2.938 0.188,0.167 10 false 10

Install and uniformly tighten the 10 cylinder head bolts with the spacers in several steps, in the sequence shown in the illustration.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

The cylinder head bolts are tightened in 4 progressive steps.

·

If a cylinder head bolt is broken or deformed, replace it.





e.
A158686E10
1.5,1.156 1.219,1.667 1.219,1.667 1.219,1.802 true 1.042,0.365 1.281,0.531 0.24,0.167 10 false 90° 1.135,1.865 1.323,2.021 0.188,0.156 10 false *1

Step 2:

i.

Mark the cylinder head bolt heads with paint as shown in the illustration.

Text in Illustration
*1 Painted Mark
V100136

Front


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



f.
A158687E07
1.854,0.563 1.354,0.281 1.354,0.281 1.219,0.281 true 2.563,0.281 2.813,0.448 0.25,0.167 10 false 90° 1.01,0.219 1.198,0.375 0.188,0.156 10 false *1

Step 3:

i.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.

Text in Illustration
*1 Painted Mark
V100136

Front



g.
A164864E06
1.865,0.177 1.583,0.177 false 2.583,0.917 1.844,0.167 1.844,0.167 1.563,0.167 true 2.771,1.573 3.021,1.729 0.25,0.156 10 false 90° 1.365,0.104 1.552,0.26 0.188,0.156 10 false *1

Step 4:

i.

Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.

Text in Illustration
*1 Painted Mark
V100136

Front



h.

Check that the painted marks are now facing the exhaust port side.


Hide 4.INSTALL NO. 2 VALVE LASH ADJUSTER ASSEMBLY

NOTICE:

Be sure to inspect the valve lash adjuster before installing it (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


a.

Install the 16 No. 2 valve lash adjusters to the cylinder head.

HINT:

Install the lash adjuster at the same place it was removed from.



Hide 5.INSTALL NO. 2 VALVE ROCKER ARM

a.
A181682

Apply engine oil to the lash adjuster tips and valve stem ends.


b.

Install the 16 No. 2 valve rocker arms as shown in the illustration.

HINT:
A164641

Install the valve rocker arm at the same place it was removed from.



Hide 6.INSTALL NO. 5 CAMSHAFT BEARING CAP

a.

Align the camshaft bearing cap and the ring pins of the cylinder head, and install the cap.


Hide 11101 9.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

a.

Place the cylinder head on the cylinder head gasket.

NOTICE:

Ensure that no oil is on the mounting surface of the cylinder head.



b.

c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.

Step 1:

i.
U162892E02
1.531,2.865 1.688,3.031 0.156,0.167 10 false 1 1.542,0.479 1.698,0.646 0.156,0.167 10 false 2 2.167,0.479 2.323,0.646 0.156,0.167 10 false 3 2.167,2.865 2.323,3.031 0.156,0.167 10 false 4 0.938,2.875 1.094,3.042 0.156,0.167 10 false 5 0.927,0.479 1.083,0.646 0.156,0.167 10 false 6 2.771,0.49 2.927,0.656 0.156,0.167 10 false 7 2.771,2.865 2.927,3.031 0.156,0.167 10 false 8 0.344,2.875 0.5,3.042 0.156,0.167 10 false 9 0.292,0.479 0.479,0.646 0.188,0.167 10 false 10

Install and uniformly tighten the 10 cylinder head bolts with the spacers in several steps, in the sequence shown in the illustration.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

The cylinder head bolts are tightened in 4 progressive steps.

·

If a cylinder head bolt is broken or deformed, replace it.





e.
A158686E10
1.5,1.156 1.219,1.667 1.219,1.667 1.219,1.802 true 1.042,0.365 1.281,0.531 0.24,0.167 10 false 90° 1.135,1.865 1.323,2.021 0.188,0.156 10 false *1

Step 2:

i.

Mark the cylinder head bolt heads with paint as shown in the illustration.

Text in Illustration
*1 Painted Mark
V100136

Front


ii.

Tighten the cylinder head bolts 90° in the sequence shown in step 1.



f.
A158687E07
1.854,0.563 1.354,0.281 1.354,0.281 1.219,0.281 true 2.563,0.281 2.813,0.448 0.25,0.167 10 false 90° 1.01,0.219 1.198,0.375 0.188,0.156 10 false *1

Step 3:

i.

Tighten the cylinder head bolts another 90° in the sequence shown in step 1.

Text in Illustration
*1 Painted Mark
V100136

Front



g.
A164864E06
1.865,0.177 1.583,0.177 false 2.583,0.917 1.844,0.167 1.844,0.167 1.563,0.167 true 2.771,1.573 3.021,1.729 0.25,0.156 10 false 90° 1.365,0.104 1.552,0.26 0.188,0.156 10 false *1

Step 4:

i.

Tighten the cylinder head bolts by an additional 90° in the sequence shown in step 1.

Text in Illustration
*1 Painted Mark
V100136

Front



h.

Check that the painted marks are now facing the intake port side.


Hide 13750 10.INSTALL NO. 1 VALVE LASH ADJUSTER ASSEMBLY

NOTICE:

Be sure to inspect the valve lash adjuster before installing it (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


a.

Install the 16 No. 1 valve lash adjusters to the cylinder head.

HINT:

Install the lash adjuster at the same place it was removed from.



Hide 13801 11.INSTALL NO. 1 VALVE ROCKER ARM

a.
A181682

Apply engine oil to the lash adjuster tips and valve stem ends.


b.

Install the 16 No. 1 valve rocker arms as shown in the illustration.

HINT:
A164641

Install the valve rocker arm at the same place it was removed from.



Hide 12.INSTALL NO. 2 CAMSHAFT BEARING CAP

a.

Align the camshaft bearing cap and the ring pins of the cylinder head, and install the cap.


Hide 13.SET NO. 1 CYLINDER TO 45° BEFORE TDC

a.
A164515

Using a bar, turn the crankshaft counterclockwise until the No. 1 cylinder is at a position 45° before TDC.

NOTICE:

Do not turn the crankshaft again until after the timing gear is installed.


HINT:

The No. 1 cylinder is at a position 45° before TDC if the crankshaft counterweight is overlapping the cylinder block hole as shown in the illustration.



b.

Remove the 2 crankshaft pulley set bolts.


Hide 13511 14.INSTALL NO. 1 AND NO. 2 CAMSHAFTS

a.
A385652

Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.


b.
A164816

Apply engine oil to the rollers of the valve rocker arms and the camshaft housing of the cylinder head.


c.
A164519

Install the camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.

Align the timing marks (2 dot marks) on the back side of the No. 1 and No. 2 camshaft timing gears as shown in the illustration.


iii.

Place the camshafts into the cylinder head.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.




d.
A164791

Install the No. 1 camshaft bearing cap.

i.

Align the No. 1 camshaft bearing cap and the ring pins of the No. 2 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



e.
A164527

Install the No. 3 camshaft bearing caps.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.



f.
A164792

Temporarily install the No. 1 and No. 2 camshaft oil feed pipes with the 8 bolts by hand.

NOTICE:

If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.


HINT:

The pipe is bent on the intake side, and straight on the exhaust side.



g.
A164793

Temporarily install the 2 union bolts by hand.


h.
U163189E02
1.958,1.25 2.115,1.417 0.156,0.167 10 false 1 0.896,1.885 1.073,2.052 0.177,0.167 10 false 10 1.573,1.885 1.729,2.052 0.156,0.167 10 false 2 1.302,0.865 1.479,1.042 0.177,0.177 10 false 11 1.969,0.875 2.125,1.052 0.156,0.177 10 false 3 0.885,0.198 1.063,0.365 0.177,0.167 10 false 12 1.563,0.198 1.719,0.365 0.156,0.167 10 false 4 3.177,1.25 3.354,1.417 0.177,0.167 10 false 13 2.594,1.25 2.75,1.417 0.156,0.167 10 false 5 2.771,1.906 2.948,2.073 0.177,0.167 10 false 14 2.188,1.885 2.344,2.052 0.156,0.167 10 false 6 3.177,0.875 3.354,1.052 0.177,0.177 10 false 15 2.594,0.896 2.75,1.073 0.156,0.177 10 false 7 2.781,0.208 2.958,0.375 0.177,0.167 10 false 16 2.219,0.208 2.375,0.375 0.156,0.167 10 false 8 0.094,1.51 0.271,1.677 0.177,0.167 10 false 17 1.354,1.229 1.51,1.396 0.156,0.167 10 false 9 0.146,1.948 0.323,2.115 0.177,0.167 10 false 18 0.094,0.635 0.271,0.802 0.177,0.167 10 false 19 0.104,0.167 0.281,0.333 0.177,0.167 10 false 20 0.594,2.448 0.781,2.604 0.188,0.156 10 false *1 0.594,2.906 0.781,3.063 0.188,0.156 10 false *2

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 12 mm Head Bolt
*2 10 mm Head Bolt


i.
A164793

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


j.
A164905

Remove the service bolt from the No. 1 camshaft timing gear.

NOTICE:

Do not drop the bolt into the engine.



Hide 13053 15.INSTALL NO. 3 AND NO. 4 CAMSHAFTS

a.
A385652

Add more than 19 cc (1.16 cu. in.) of engine oil into the cylinder head side oil holes.


b.
A164816

Apply engine oil to the rollers of the valve rocker arms and camshaft housing of the cylinder head.


c.
A164520

Install the camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.

Align the timing marks (1 dot mark) on the back side of the No. 3 and No. 4 camshaft timing gears as shown in the illustration.


iii.

Place the camshafts into the cylinder head.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the rocker arms to the lash adjusters.




d.
A164794

Install the No. 4 camshaft bearing cap.

i.

Align the No. 4 camshaft bearing cap and the ring pins of the No. 5 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



e.
A164536

Install the No. 3 camshaft bearing caps.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the oil feed pipe, by hand.



f.
A164795

Temporarily install the No. 3 and No. 4 camshaft oil feed pipes with the 8 bolts by hand.

NOTICE:

If even one of the pipe bolt holes does not match its camshaft bearing cap bolt hole, replace the camshaft oil feed pipe.


HINT:

The pipe is bent on the intake side, and straight on the exhaust side.



g.
A164783

Temporarily install the 2 union bolts by hand.


h.
U163192E02
1.958,1.25 2.115,1.417 0.156,0.167 10 false 1 0.917,1.917 1.094,2.083 0.177,0.167 10 false 10 1.573,1.917 1.729,2.083 0.156,0.167 10 false 2 1.313,0.875 1.49,1.042 0.177,0.167 10 false 11 1.958,0.875 2.115,1.042 0.156,0.167 10 false 3 0.896,0.167 1.073,0.333 0.177,0.167 10 false 12 1.573,0.167 1.729,0.333 0.156,0.167 10 false 4 3.177,1.25 3.354,1.417 0.177,0.167 10 false 13 2.604,1.25 2.76,1.417 0.156,0.167 10 false 5 2.75,1.938 2.927,2.104 0.177,0.167 10 false 14 2.188,1.917 2.344,2.083 0.156,0.167 10 false 6 3.188,0.875 3.365,1.042 0.177,0.167 10 false 15 2.615,0.875 2.771,1.042 0.156,0.167 10 false 7 2.792,0.177 2.969,0.344 0.177,0.167 10 false 16 2.208,0.156 2.365,0.323 0.156,0.167 10 false 8 0.104,1.5 0.281,1.667 0.177,0.167 10 false 17 1.354,1.25 1.51,1.417 0.156,0.167 10 false 9 0.208,1.969 0.385,2.135 0.177,0.167 10 false 18 0.094,0.635 0.271,0.802 0.177,0.167 10 false 19 0.115,0.177 0.292,0.344 0.177,0.167 10 false 20 0.573,2.417 0.76,2.573 0.188,0.156 10 false *1 0.573,2.896 0.76,3.052 0.188,0.156 10 false *2

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 12 mm Head Bolt
*2 10 mm Head Bolt


i.
A164783

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


j.
A164905

Remove the service bolt from the No. 4 camshaft timing gear.

NOTICE:

Do not drop the bolt into the engine.



Hide 11338A 16.INSTALL NO. 2 TIMING GEAR CASE INSULATOR (w/ Intercooler)

Hide 25707 17.INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

a.

Install the No. 2 vacuum transmitting pipe with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 25706 18.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

a.

Install the No. 1 vacuum transmitting pipe with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 25770A 19.CONNECT NO. 3 VACUUM TRANSMITTING HOSE (w/ Intercooler)

Hide 25770 20.CONNECT NO. 2 VACUUM TRANSMITTING HOSE (w/ Intercooler)

Hide 11301 21.INSTALL TIMING GEAR CASE SUB-ASSEMBLY

NOTICE:

When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.

A158670E02
0.181,0.147 0.366,0.302 0.185,0.155 10 *a 3.845,0.147 4.030,0.302 0.185,0.155 10 *b


Text in Illustration
*a Cylinder Block *b Timing Gear Case

a.

Apply seal packing to the timing gear case as shown in the following illustration.

Standard seal diameter:

4 to 5 mm (0.157 to 0.197 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

After applying seal packing, align the timing gear case with the engine within 3 minutes and tighten the bolts and nuts within 15 minutes.

·

Apply the seal packing in a continuous line.



HINT:
·

The FIPG line is shown below.

·

Apply packing to the 5 seal surface areas.



A158675E03
4.019,1.144 5.256,1.338 1.237,0.194 10 2.5 mm (0.0984 in.) 5.758,1.144 7.008,1.321 1.250,0.177 10 2.0 mm (0.0787 in.) 5.373,0.719 5.645,0.887 0.272,0.168 10 A-A 1.11,1.07 1.254,1.210 0.145,0.140 10 A 1.535,1.159 1.680,1.299 0.145,0.140 10 A 5.769,1.577 5.954,1.732 0.185,0.155 10 *a

Text in Illustration
*a Seal Diameter: 4 to 5 mm - -


b.
A181226E04
0.938,1.99 0.938,2.854 false 2.563,2.083 2.563,2.854 false 0.427,1.073 0.542,1.073 0.542,1.073 1.125,1.771 true 0.229,0.99 0.417,1.146 0.188,0.156 10 false *1 0.854,2.917 1.042,3.073 0.188,0.156 10 false *2 2.479,2.917 2.667,3.073 0.188,0.156 10 false *2

Install a new timing gear case gasket.

Text in Illustration
*1 New Timing Gear Case Gasket
*2 New O-Ring


c.

Apply engine oil to 2 new O-rings and install them to the timing gear case.


d.
A164512E03
1.109,2.805 1.294,2.960 0.185,0.155 10 *1 2.103,2.805 2.288,2.960 0.185,0.155 10 *1 0.723,3.235 0.908,3.390 0.185,0.155 10 *2 0.723,3.759 0.908,3.914 0.185,0.155 10 *3 0.723,4.285 0.908,4.439 0.185,0.155 10 *4

Install the timing gear case with the 22 bolts and 2 nuts.

Torque:
for 14 mm head bolt (When "dry") : 46 N*m (469 kgf*cm, 34 ft.*lbf)
for 14 mm head bolt (When "wet") : 42 N*m (428 kgf*cm, 31 ft.*lbf)
for 12 mm head bolt A and B : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for nut : 29 N*m (296 kgf*cm, 21 ft.*lbf)

Text in Illustration
*1 Nut
*2 14 mm Head Bolt
*3 12 mm Head Bolt A
*4 12 mm Head Bolt B

NOTICE:
·

The case is "dry" when there is absolutely no engine oil on the 14 mm head bolts and cylinder head bolt holes.

·

The case is "wet" when there is engine oil on the 14 mm head bolts and cylinder head bolt holes.



Bolt Length
Item Quantity Length
A 4 20 mm (0.787 in.)
B 8 45 mm (1.77 in.)


Hide 11248 22.INSTALL V-BANK SILENCER

a.

Align the alignment areas of the V-bank silencer and cylinder block, and install the V-bank silencer.

NOTICE:

Verify that the V-bank silencer is below the top surface of the intake port of the cylinder head RH and LH.



Hide 22100 23.INSTALL FUEL SUPPLY PUMP ASSEMBLY

a.
A164817

Using an 8 mm x 1.25 pitch tap, remove the adhesive from the timing gear case side bolt hole.


b.
A164818E05
2.198,0.406 1.635,0.229 1.635,0.229 1.521,0.229 true 1.302,0.146 1.698,0.385 0.396,0.24 10 true *1

Apply adhesive to 2 or more threads of the timing gear case bolt hole.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Text in Illustration
*1 Adhesive


c.
A164821E02
0.04,1.421 0.225,1.576 0.185,0.155 10 *1 0.651,1.51 0.246,1.51 false

Apply engine oil to a new O-ring and install it to the supply pump.

Text in Illustration
*1 New O-Ring


d.

Install the supply pump to the timing gear case.

NOTICE:

When installing the supply pump, do not hold the fuel pipe to prevent fuel leaks.


i.

Temporarily install the 2 nuts.


ii.

Using a 6 mm hexagon wrench, install the hexagon bolt, and then tighten the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)



Hide 24.INSTALL STRAIGHT PIN

a.

Install the straight pin.

Standard protrusion height:

4.5 to 7.0 mm (0.177 to 0.276 in.)



Hide 13616 25.ASSEMBLE FUEL SUPPLY PUMP DRIVE GEAR AND FUEL SUPPLY PUMP SHAFT SPROCKET

a.

Align the fuel supply pump drive gear to the fuel supply pump shaft sprocket straight pin and temporarily install it with the 4 bolts.


b.

Hold the fuel supply pump shaft sprocket in a vise between aluminum plates.

NOTICE:

Be careful not to damage the gears.



c.

Tighten the 4 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 26.INSTALL RADIAL BALL BEARING

a.
U162858E02
2.354,1.302 2.229,1.781 2.229,1.781 2.375,1.781 true 2.542,1.427 2.448,1.427 2.448,1.427 2.583,0.906 true 0.979,0.427 0.448,0.427 true 0.979,0.708 0.604,0.708 0.604,0.708 0.604,0.438 true 0.115,0.354 0.417,0.5 0.302,0.146 10 false SST 2.344,0.208 2.5,0.375 0.156,0.167 10 false B 3.135,0.521 3.292,0.688 0.156,0.167 10 false A 2.521,1.323 3.302,1.531 0.781,0.208 10 true *1 2.438,1.698 2.625,1.854 0.188,0.156 10 false *2

Using SST and a press, press in the radial ball bearing to the fuel supply pump shaft sprocket.

SST
09316-12010  
09950-60010  (09951-00580)

Text in Illustration
*1 Radial Ball Bearing
*2 Fuel Supply Pump Shaft Sprocket

NOTICE:
·

Make sure to press in the bearing until the bearing contacts the fuel supply pump shaft sprocket, as shown in A in the illustration.

·

Make sure the sprocket outer edge is further outward than the bearing outer edge, as shown in B in the illustration.




Hide 13613 27.TEMPORARILY INSTALL FUEL SUPPLY PUMP DRIVE GEAR

a.
A164525

Align the cutout of the supply pump drive gear and key of the supply pump, and temporarily install the fuel supply pump drive gear nut.


Hide 28.SET NO. 1 AND NO. 2 CAMSHAFTS TO TDC

a.
A164516

Using a wrench, turn the No. 1 camshaft and align the timing marks (1 dot mark) on the back side of the timing gears as shown in the illustration.


Hide 13581 29.INSTALL NO. 1 IDLE GEAR SHAFT

a.
A164840

Apply engine oil to the contact surface of the idle gear shaft and the back side of the protrusion.


b.

Install the idle gear shaft to the cylinder block.


Hide 30.ASSEMBLE SUB GEAR, IDLE GEAR SPRING AND IDLE GEAR (w/ Intercooler)

a.
A180311

Hold the idle gear in a vise between aluminum plates.

NOTICE:

Be careful not to damage the gears.



b.
A180312

Align the right end of the idle gear spring to the notch of the idle gear and set it to the gear.


c.
A177422

Install the sub idle gear.

i.

Align the notch of the sub idle gear protrusion with the left end of the idle gear spring and install the sub idle gear to the idle gear.


ii.
A177423E03
0.823,0.188 0.979,0.188 0.979,0.188 1.229,0.781 true 2.188,0.198 2.646,0.198 false 0.458,0.104 0.75,0.26 0.292,0.156 10 false SST 2,0.125 2.188,0.281 0.188,0.156 10 false *1

Using SST, turn the sub idle gear counterclockwise, and install an 8 mm x 1.25 pitch bolt with a length of 15 mm or more to the service hole.

SST
09960-10010  (09962-01000, 09963-00700)

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 Service Bolt



Hide 13520A 31.INSTALL IDLE GEAR ASSEMBLY

a.
A170353E04
1.385,0.75 0.5,0.75 true 1.135,0.052 1.385,0.229 0.25,0.177 10 true 45° 0.302,0.667 0.563,0.896 0.26,0.229 10 true *1

Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.

Text in Illustration
*1 Key


b.

Using a bar, turn the crankshaft clockwise to the No. 1 cylinder TDC position.


c.

Align the timing marks of the supply pump drive gear and idle gear, and the timing marks of the crankshaft timing gear and idle gear as shown in the illustration.

A257019E02
0.62,0.253 0.805,0.408 0.185,0.155 10 *A 4.098,0.253 4.283,0.408 0.185,0.155 10 *B

Text in Illustration
*A w/ Intercooler *B w/o Intercooler


d.

Apply engine oil to the idle gear thrust plate and gears.


e.

Install the idle gear thrust plate with the 2 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


f.

w/ Intercooler:

Remove the service bolt.


Hide 32.TIGHTEN FUEL SUPPLY PUMP DRIVE GEAR NUT

a.

Using SST, hold the idle gear and tighten the nut.

SST
09960-10010  (09962-01000, 09963-00700)

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)

A257020E04
0.51,0.01 0.781,0.229 0.271,0.219 4.042,0.01 4.313,0.229 0.271,0.219 0.708,2.385 0.813,2.385 0.813,2.385 1.948,1.76 true 4.24,2.385 4.344,2.385 4.344,2.385 5.479,1.76 true 0.385,2.313 0.719,2.458 0.333,0.146 10 false SST 3.917,2.313 4.25,2.458 0.333,0.146 10 false SST 0.552,0.042 0.74,0.198 0.188,0.156 10 false *A 4.094,0.042 4.281,0.198 0.188,0.156 10 false *B

Text in Illustration
*A w/ Intercooler *B w/o Intercooler


Hide 33.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Check that the timing marks of the following pairs of parts are aligned: 1) supply pump drive gear and idle gear: 2) crankshaft timing gear and idle gear: 3) RH and LH camshaft timing gears.

A177357


Hide 13529G 34.INSTALL NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 TIMING CHAIN

a.
A164523

Align the 2 mark plates (yellow) on the No. 2 timing chain with the timing mark (1 dot mark) of the No. 2 camshaft timing sprocket as shown in the illustration.


b.
A174774E05
0.792,0.542 2.052,0.542 true 2.552,2.073 2.656,2.073 2.656,2.073 2.656,2.531 true 2.125,0.469 2.313,0.625 0.188,0.156 10 false *1 2.375,1.99 2.615,2.198 0.24,0.208 10 true *1

Align the No. 2 timing chain mark plate (yellow) with the supply pump drive gear timing mark, and temporarily install the No. 2 camshaft timing sprocket with the 4 bolts.

Text in Illustration
*1 Timing Mark


c.
A164506E03
2.979,1.219 2.979,1.552 false 2.844,1.594 3.135,1.771 0.292,0.177 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket, and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 13523 35.INSTALL NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 TIMING CHAIN

a.
A164521

Align the 2 mark plates (yellow) on the No. 1 timing chain with the timing mark (1 dot mark) of the No. 1 camshaft timing sprocket as shown in the illustration.


b.
A174775E05
2.5,0.625 1.115,0.625 true 0.844,2.958 1.729,2.542 1.729,2.542 1.854,2.542 true 0.938,0.542 1.125,0.698 0.188,0.156 10 false *1 1.833,2.417 2.135,2.698 0.302,0.281 10 true *1

Align the No. 1 timing chain mark plate (yellow) with the supply pump drive gear timing mark, and temporarily install the No. 1 camshaft timing sprocket.

Text in Illustration
*1 Timing Mark


Hide 13522 36.INSTALL PUMP DRIVE SHAFT GEAR

a.
A164498E01
0.077,0.46 0.373,0.622 0.296,0.162 10 SST 0.463,0.546 0.597,0.546 0.597,0.546 0.909,1.156 false

Temporarily install the pump drive shaft gear with the 4 bolts.


b.

Using SST, hold the pump drive shaft gear and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 37.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the No. 2 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 38.INSTALL NO. 2 CHAIN TENSIONER SLIPPER

Hide 39.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A164589

Move the stopper plate clockwise to release the lock, and push the plunger into the tensioner.


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.

Install the No. 2 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench.


Hide 13561 40.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 41.INSTALL NO. 1 CHAIN TENSIONER SLIPPER

Hide 13540 42.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A164589

Move the stopper plate clockwise to release the lock, and push the plunger into the tensioner.


b.

Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.

Install the No. 1 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench.


Hide 19315 43.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Remove the adhesive from the threads of the 2 screws and the bolt holes of the crankshaft.


b.
A164913E03
1.385,0.583 1.51,0.583 1.51,0.583 1.781,0.917 false 1.167,0.5 1.354,0.656 0.188,0.156 10 false *1

Apply adhesive to 2 or 3 threads of the 2 screws.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Text in Illustration
*1 Adhesive


c.

Using a T30 "TORX" wrench, install the No. 1 crankshaft position sensor plate with the 2 screws.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure the "F" mark on the plate is facing towards the front side of the engine.


HINT:

When replacing the No. 1 crankshaft position sensor plate, perform "Crank Time Compensation Reset" (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).



Hide 44.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.


b.

Rotate the crankshaft 2 revolutions or more so that the crankshaft key is 45° counterclockwise from the top. Check that the timing marks (1 dot mark each) of the RH and LH camshaft timing gears align. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks. If the timing marks are deviated, reinstall the chain and camshaft.

A174764E06
0.448,5.969 0.448,5.844 0.448,5.844 1.031,5.688 true 0.885,5.01 1.115,5.167 0.229,0.156 10 false 45° 0.323,5.969 0.604,6.302 0.281,0.333 10 true *1 1.365,4.896 1.552,5.052 0.188,0.156 10 false *a

Text in Illustration
*1 Key - -
*a Top - -


c.

Remove the 2 crankshaft pulley set bolts.


Hide 45.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
U162907E02
2.021,2.49 0.552,2.74 0.552,2.74 0.552,2.917 true 0.427,2.979 0.729,3.135 0.302,0.156 10 false SST 0.74,1.729 0.896,1.896 0.156,0.167 10 false A

Place the timing chain cover on wooden blocks.


b.

Using SST and a hammer, tap in a new oil seal as shown in the illustration.

SST
09316-12010  
09950-70010  (09951-07100)
09950-60020  (09951-00890)

Standard depth A:

0.6 to 1.4 mm (0.0236 to 0.0551 in.)



Hide 11302 46.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

NOTICE:

When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.

A158671E02
0.487,0.202 0.671,0.356 0.185,0.155 10 *1 3.912,0.202 4.097,0.356 0.185,0.155 10 *2


Text in Illustration
*1 Timing Gear Case *2 Timing Chain Cover

a.
A174785E04
1.771,1.521 1.771,1.719 true 1.677,1.74 1.969,1.99 0.292,0.25 10 true *1

Install a new O-ring to the timing gear case.

Text in Illustration
*1 New O-Ring


b.

Apply seal packing to the timing chain cover as shown in the following illustration.

Standard seal diameter:

4 to 5 mm (0.157 to 0.197 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

After applying seal packing, align the timing chain cover with the timing gear case within 3 minutes and tighten the bolts and nuts within 15 minutes.

·

Apply the seal packing in a continuous line.

·

Make sure the seal packing does not become thinner than 4 mm (0.157 in.) at the areas labeled "B" in the illustration below.



HINT:
·

The FIPG line is shown below.

·

Apply packing to the 6 seal surface areas.


U162857E02
6.594,1.781 6.594,2.042 false 4.396,1.479 5.625,1.646 1.229,0.167 10 false 2.5 mm (0.0984 in.) 5.927,1.469 7.156,1.646 1.229,0.177 10 false 2.0 mm (0.0787 in.) 5.771,0.906 6.042,1.063 0.271,0.156 10 false A-A 3.135,2.323 3.271,2.49 0.135,0.167 10 false A 2.698,2.198 2.833,2.365 0.135,0.167 10 false A 1.646,0.51 1.802,0.677 0.156,0.167 10 false B 1.417,2.063 1.573,2.229 0.156,0.167 10 false B 6.51,2.135 6.698,2.292 0.188,0.156 10 false *a


Text in Illustration
*a Seal Diameter: 4 to 5 mm - -


c.

Apply engine oil to the lip of the oil seal.


d.

Align and install the timing chain cover to the timing gear case knock pin and supply pump bearing.

NOTICE:

Make sure that the lip of the oil seal is properly installed.



e.
A168359E02
0.593,2.926 0.778,3.080 0.185,0.155 10 *1

If the stud bolts are loose, tighten them using an E7 "TORX" wrench.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

Text in Illustration
*1 Stud Bolt


f.
U163086E02
1.01,0.115 1.167,0.281 0.156,0.167 10 false 1 0.313,1.281 0.49,1.448 0.177,0.167 10 false 10 1.458,3.094 1.615,3.26 0.156,0.167 10 false 2 1.635,1.583 1.813,1.75 0.177,0.167 10 false 11 1.083,2.76 1.24,2.927 0.156,0.167 10 false 3 1.385,1.177 1.563,1.344 0.177,0.167 10 false 12 1,2.479 1.156,2.646 0.156,0.167 10 false 4 0.667,0.333 0.844,0.5 0.177,0.167 10 false 13 1.594,1.844 1.75,2.021 0.156,0.177 10 false 5 1.281,0.375 1.458,0.542 0.177,0.167 10 false 14 0.896,2.24 1.052,2.406 0.156,0.167 10 false 6 1.229,0.104 1.406,0.271 0.177,0.167 10 false 15 0.656,2.24 0.813,2.406 0.156,0.167 10 false 7 1.813,0.313 1.99,0.479 0.177,0.167 10 false 16 0.406,2.24 0.563,2.406 0.156,0.167 10 false 8 2.083,0.094 2.26,0.26 0.177,0.167 10 false 17 0.104,2.094 0.26,2.26 0.156,0.167 10 false 9 3.198,2.01 3.375,2.177 0.177,0.167 10 false 18 2.885,2.177 3.063,2.344 0.177,0.167 10 false 19 2.427,2.323 2.604,2.49 0.177,0.167 10 false 20 1.854,3.125 2.031,3.292 0.177,0.167 10 false 21 0.375,2.729 0.563,2.885 0.188,0.156 10 false *1

Install and uniformly tighten the 16 bolts and 4 nuts in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Nut


Hide 49.TEMPORARILY INSTALL INTAKE MANIFOLD

a.
A177324

Install the gasket and temporarily install the No. 2 intake manifold with the 9 bolts.


b.
A177323

Install the gasket and temporarily install the No. 1 intake manifold with the 9 bolts.


c.
U162996E03
0.719,2.698 0.875,2.865 0.156,0.167 10 false A 0.729,3.094 0.885,3.26 0.156,0.167 10 false B

Install the 2 gaskets and temporarily install the No. 3 intake manifold with the 16 bolts.

Bolt Length
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 70 mm (2.76 in.)


Hide 50.INSTALL FUEL INJECTOR LH (w/o DPF)

NOTICE:

Be sure to install the injector, holder clamp and bolt in their original positions.


a.
A164163

Install 4 new injection nozzle seats to the cylinder head.


b.

Apply a light coat of clean engine oil to 4 new O-rings.


c.
A164164E03
1.824,1.362 1.824,1.746 false 1.706,1.769 1.890,1.924 0.185,0.155 10 *1

Install an O-ring to each injector as shown in the illustration.

Text in Illustration
*1 New O-Ring


d.

Insert the 4 injectors into the cylinder head.

NOTICE:
·

Insert the injector until it touches the nozzle seat surface.

·

After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.

·

Always return an injector to the same place it was removed from.




e.

For an injector that has been replaced with a new injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).


f.
A385836E01
0.438,0.438 0.625,0.438 0.625,0.438 0.698,0.854 false 1.156,3.531 1.156,3.76 1.156,3.76 1.563,3.771 true 2.146,3.542 2.146,3.771 2.146,3.771 1.542,3.771 true 1.656,4.073 1.656,3.781 false 0.24,0.365 0.552,0.563 0.313,0.198 10 false *1 0.594,1.354 0.906,1.552 0.313,0.198 10 false *a 1.573,4.125 1.885,4.323 0.313,0.198 10 false *2

Temporarily install 4 new washers and the 4 nozzle clamps with the 4 clamp bolts.

Text in Illustration
*1 New Washer
*2 Nozzle Holder Clamp
*a Downward

NOTICE:
·

The fork portion of the nozzle holder clamp must be set to the injector.

·

Before tightening the bolts, check that the nozzle holder clamps are set properly.

·

To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, pay attention not to tilt the bolt and clamp.

·

Do not reuse the washer.




g.
A163353

Temporarily install the common rail LH with the 2 bolts.


h.
A168840

Temporarily install the 4 new injection pipes to the common rail and injectors.


i.
A062123E07
0.854,1.042 0.854,1.5 false 0.771,1.573 1.083,1.771 0.313,0.198 10 false *1

Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.

Text in Illustration
*1 Nozzle Leakage Pipe


j.

Set the nozzle leakage pipe and 5 new gaskets in place.


k.
A164167

Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

HINT:

To position the injectors, loosely tighten the 4 hollow screws and union bolt.



l.
A164165

Tighten the 4 holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.
A168840

Remove the 4 injection pipes.


n.
A163353

Remove the 2 bolts and common rail LH.


o.
A165056

Tighten the 4 hollow screws.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.



p.
A165057

Tighten the union bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.



Hide 23670 51.INSTALL FUEL INJECTOR RH (w/o DPF)

NOTICE:

Be sure to install the injector, holder clamp and bolt in their original positions.


a.
A164163

Install 4 new injection nozzle seats to the cylinder head.


b.

Apply a light coat of clean engine oil to 4 new O-rings.


c.
A164164E03
1.824,1.362 1.824,1.746 false 1.706,1.769 1.890,1.924 0.185,0.155 10 *1

Install an O-ring to each injector as shown in the illustration.

Text in Illustration
*1 New O-Ring


d.

Insert the 4 injectors into the cylinder head.

NOTICE:
·

Insert the injector until it touches the nozzle seat surface.

·

After installing the injector to the cylinder head, the O-ring may prevent the injector from fully seating. If so, pull out the injector and reinstall it.

·

Always return an injector to the same place it was removed from.




e.

For an injector that has been replaced with a new injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).


f.
A385836E01
0.438,0.438 0.625,0.438 0.625,0.438 0.698,0.854 false 1.156,3.531 1.156,3.76 1.156,3.76 1.563,3.771 true 2.146,3.542 2.146,3.771 2.146,3.771 1.542,3.771 true 1.656,4.073 1.656,3.781 false 0.24,0.365 0.552,0.563 0.313,0.198 10 false *1 0.594,1.354 0.906,1.552 0.313,0.198 10 false *a 1.573,4.125 1.885,4.323 0.313,0.198 10 false *2

Temporarily install 4 new washers and the 4 nozzle clamps with the 4 clamp bolts.

Text in Illustration
*1 New Washer
*2 Nozzle Holder Clamp
*a Downward

NOTICE:
·

The fork portion of the nozzle holder clamp must be set to the injector.

·

Before tightening the bolts, check that the nozzle holder clamp is set properly.

·

To tighten the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a later step.

·

When tightening the bolts, pay attention not to tilt the bolt and clamp.

·

Do not reuse the washer.




g.
A168360

Temporarily install the common rail RH with the 2 bolts.


h.
A168839

Temporarily install the 4 new injection pipes to the common rail and injectors.


i.
A062123E07
0.854,1.042 0.854,1.5 false 0.771,1.573 1.083,1.771 0.313,0.198 10 false *1

Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces. If scratches or dents are present, replace the nozzle leakage pipe.

Text in Illustration
*1 Nozzle Leakage Pipe


j.

Set the nozzle leakage pipe and 5 new gaskets in place.


k.
A164168

Temporarily install the nozzle leakage pipe with the 4 hollow screws and union bolt.

HINT:

To position the injectors, loosely tighten the 4 hollow screws and union bolt.



l.
A164166

Tighten the 4 holder clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


m.
A168839

Remove the 4 injection pipes.


n.
A168360

Remove the 2 bolts and common rail RH.


o.
A165023

Tighten the 4 hollow screws.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

If a hollow screw is accidentally tightened beyond the torque specification, it must be replaced.



p.
A165024

Tighten the union bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.



Hide 11202 52.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/ DPF)

a.
A271747

Temporarily install 2 service stud bolts (8 mm x 1.25 pitch with a length of 30 mm or more) to the 2 locations shown in the illustration.


b.
A267299

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




c.

Install a new cylinder head cover gasket LH and new No. 4 cylinder head cover gasket to the cylinder head cover LH.

NOTICE:

Remove any oil from the contact surface.



d.

Using the service stud bolts as guides, place the cylinder head cover LH on the cylinder head.


e.

Remove the 2 service stud bolts.


f.
U163553E02
2.552,1.406 2.75,1.552 0.198,0.146 10 false 23 0.49,1.833 0.688,1.979 0.198,0.146 10 false 16 1.635,1.646 1.76,1.792 0.125,0.146 10 false 1 1.646,2.094 1.771,2.24 0.125,0.146 10 false 2 1.656,1.208 1.781,1.354 0.125,0.146 10 false 3 1.646,2.521 1.771,2.667 0.125,0.146 10 false 4 1.646,0.813 1.771,0.958 0.125,0.146 10 false 5 0.854,1.833 0.979,1.979 0.125,0.146 10 false 6 2.531,1.844 2.656,2.073 0.125,0.229 10 false 7 2.49,2.927 2.688,3.073 0.198,0.146 10 false 10 2.583,2.219 2.74,2.438 0.156,0.219 10 false 8 2.656,2.563 2.802,2.74 0.146,0.177 10 false 9 1.844,3.156 2.042,3.302 0.198,0.146 10 false 11 1.135,3.177 1.333,3.323 0.198,0.146 10 false 12 0.521,3.052 0.719,3.198 0.198,0.146 10 false 13 0.427,2.531 0.625,2.677 0.198,0.146 10 false 14 0.698,2.24 0.896,2.385 0.198,0.146 10 false 15 0.75,1.406 0.948,1.552 0.198,0.146 10 false 17 0.75,0.969 0.948,1.115 0.198,0.146 10 false 18 0.688,0.417 0.885,0.563 0.198,0.146 10 false 19 1.75,0.073 1.948,0.219 0.198,0.146 10 false 20 2.573,0.469 2.771,0.615 0.198,0.146 10 false 21 2.552,0.979 2.75,1.125 0.198,0.146 10 false 22 2.823,1.844 3.021,2.01 0.198,0.167 10 false 24

Temporarily install the cylinder head cover LH with the 18 bolts and 4 nozzle holder clamp seats. Tighten the 18 bolts and 4 nozzle holder clamp seats in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nozzle Holder Clamp Seat

HINT:

After tightening the bolts, check that the bolts at step 16 and 24 are tightened to the specified torque.



Hide 11201 53.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/ DPF)

a.
A271748

Temporarily install 2 service stud bolts (8 mm x 1.25 pitch with a length of 30 mm or more) to the 2 locations shown in the illustration.


b.
A267298

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after the installation.




c.

Install a new cylinder head cover gasket RH and new No. 3 cylinder head cover gasket to the cylinder head cover RH.

NOTICE:

Remove any oil from the contact surface.



d.

Using the service stud bolts as guides, place the cylinder head cover RH on the cylinder head.


e.

Remove the 2 service stud bolts.


f.
U163552E02
2.719,0.854 2.917,1 0.198,0.146 10 false 23 0.521,1.469 0.719,1.615 0.198,0.146 10 false 16 1.698,1.771 1.823,1.917 0.125,0.146 10 false 1 1.708,2.219 1.833,2.365 0.125,0.146 10 false 2 1.698,1.333 1.823,1.479 0.125,0.146 10 false 3 1.698,2.635 1.823,2.781 0.125,0.146 10 false 4 1.771,0.938 1.896,1.083 0.125,0.146 10 false 5 0.896,1.458 1.021,1.604 0.125,0.146 10 false 6 2.583,1.469 2.698,1.604 0.115,0.135 10 false 7 2.594,2.813 2.792,2.958 0.198,0.146 10 false 10 2.583,1.906 2.719,2.094 0.135,0.188 10 false 8 2.583,2.333 2.698,2.531 0.115,0.198 10 false 9 2.135,3.073 2.333,3.219 0.198,0.146 10 false 11 0.813,3.01 1.01,3.156 0.198,0.146 10 false 12 0.75,2.667 0.948,2.813 0.198,0.146 10 false 13 0.792,2.333 0.99,2.479 0.198,0.146 10 false 14 0.792,1.896 0.99,2.042 0.198,0.146 10 false 15 0.75,1.177 0.948,1.323 0.198,0.146 10 false 17 0.469,0.979 0.667,1.125 0.198,0.146 10 false 18 0.615,0.219 0.813,0.365 0.198,0.146 10 false 19 1.073,0.083 1.271,0.229 0.198,0.146 10 false 20 2.042,0.104 2.24,0.25 0.198,0.146 10 false 21 2.656,0.531 2.854,0.677 0.198,0.146 10 false 22 2.677,1.177 2.875,1.323 0.198,0.146 10 false 24 2.854,1.469 3.052,1.615 0.198,0.146 10 false 25

Temporarily install the cylinder head cover RH with the 19 bolts and 4 nozzle holder clamp seats. Tighten the 19 bolts and 4 nozzle holder clamp seats in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nozzle Holder Clamp Seat

HINT:

After tightening the bolts, check that the bolts at step 16 and 25 are tightened to the specified torque.



Hide 54.INSTALL FUEL INJECTOR LH (w/ DPF)

NOTICE:
·

Be sure to install the fuel injector, nozzle holder clamp and clamp bolt to their original positions.

·

Before installing the fuel injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head sub-assembly and fuel injector. If there is foreign matter, remove it before installing the fuel injector.



a.
A271223

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.
A354207E01
0.695,0.621 0.880,0.776 0.185,0.155 10 *1 0.9,0.716 1.582,0.716 false

Install 4 new fuel injector seals to each fuel injector as shown in the illustration.

Text in Illustration
*1 Fuel Injector Seal


c.

Apply a light coat of clean engine oil to 4 new O-rings.


d.
A354208E01
0.739,0.849 0.924,1.004 0.185,0.155 10 *1 0.948,0.941 1.622,0.941 false

Install the O-rings to each fuel injector as shown in the illustration.

Text in Illustration
*1 O-Ring


e.

Insert the 4 fuel injectors into the cylinder head sub-assembly.

NOTICE:
·

Insert the fuel injector until it touches the nozzle seat surface.

·

After installing the fuel injector to the cylinder head sub-assembly, the O-ring may prevent the fuel injector from fully seating. If so, pull out the fuel injector and reinstall it.

·

Always return an fuel injector to the same place it was removed from.




f.

For an fuel injector that has been replaced with a new fuel injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


g.
A354209E01
2.971,1.049 3.155,1.204 0.185,0.155 10 *1 3.169,1.723 3.354,1.878 0.185,0.155 10 *2 2.968,2.174 3.153,2.329 0.185,0.155 10 *3 2.239,2.261 2.94,2.261 false 2.442,1.811 3.142,1.811 false 2.239,1.134 2.94,1.134 false

Temporarily install 4 new washers, 4 nozzle holder clamps and 4 new nozzle holder seals with the 4 clamp bolts.

Text in Illustration
*1 Washer
*2 Nozzle Holder Clamp
*3 Nozzle Holder Seal

NOTICE:

When temporarily installing the clamp bolt to the nozzle holder clamp, make sure that the clamp bolt and nozzle holder clamp are not at an angle.



h.
A267323

Temporarily install the common rail assembly LH with the 2 bolts.


i.
A271636

Temporarily install 4 new injection pipes to the common rail assembly LH and fuel injector.


j.
A271219

Temporarily install the No. 2 nozzle leakage pipe and 4 used gaskets with the 4 injector hollow screws and 2 bolts.

Text in Illustration
V100135

Injector Hollow Screw
V100136

Bolt


k.

Tighten the 4 clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


l.

Remove the 4 injection pipes.


m.

Remove the 2 bolts and common rail assembly LH.


n.

Remove the 4 injector hollow screws and 4 gaskets.


o.

Remove the 2 bolts and No. 2 nozzle leakage pipe.


Hide 55.INSTALL FUEL INJECTOR RH (w/ DPF)

NOTICE:
·

Be sure to install the fuel injector, nozzle holder clamp and clamp bolt to their original positions.

·

Before installing the fuel injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head sub-assembly and fuel injector. If there is foreign matter, remove it before installing the fuel injector.



a.
A271223

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.
A354207E01
0.695,0.621 0.880,0.776 0.185,0.155 10 *1 0.9,0.716 1.582,0.716 false

Install 4 new fuel injector seals to each fuel injector as shown in the illustration.

Text in Illustration
*1 Fuel Injector Seal


c.

Apply a light coat of clean engine oil to 4 new O-rings.


d.
A354208E01
0.739,0.849 0.924,1.004 0.185,0.155 10 *1 0.948,0.941 1.622,0.941 false

Install the O-rings to each fuel injector as shown in the illustration.

Text in Illustration
*1 O-Ring


e.

Insert the 4 fuel injectors into the cylinder head sub-assembly.

NOTICE:
·

Insert the fuel injector until it touches the nozzle seat surface.

·

After installing the fuel injector to the cylinder head sub-assembly, the O-ring may prevent the fuel injector from fully seating. If so, pull out the fuel injector and reinstall it.

·

Always return an fuel injector to the same place it was removed from.




f.

For an fuel injector that has been replaced with a new fuel injector, register the injector compensation code (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).


g.
A354209E01
2.971,1.049 3.155,1.204 0.185,0.155 10 *1 3.169,1.723 3.354,1.878 0.185,0.155 10 *2 2.968,2.174 3.153,2.329 0.185,0.155 10 *3 2.239,2.261 2.94,2.261 false 2.442,1.811 3.142,1.811 false 2.239,1.134 2.94,1.134 false

Temporarily install 4 new washers, 4 nozzle holder clamps and 4 new nozzle holder seals with the 4 clamp bolts.

Text in Illustration
*1 Washer
*2 Nozzle Holder Clamp
*3 Nozzle Holder Seal

NOTICE:

When temporarily installing the clamp bolt to the nozzle holder clamp, make sure that the clamp bolt and nozzle holder clamp are not at an angle.



h.
A267324

Temporarily install the common rail assembly RH with the 2 bolts.


i.
A271637

Temporarily install 4 new injection pipes to the common rail assembly RH and fuel injector.


j.
A271215

Temporarily install the No. 1 nozzle leakage pipe and 4 used gaskets with the 4 injector hollow screws and union bolt.

Text in Illustration
V100135

Injector Hollow Screw
V100136

Union Bolt


k.

Tighten the 4 clamp bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


l.

Remove the 4 injection pipes.


m.

Remove the 2 bolts and common rail assembly RH.


n.

Remove the 4 injector hollow screws and 4 gaskets.


o.

Remove the union bolt and No. 1 nozzle leakage pipe.


Hide 56.REMOVE INTAKE MANIFOLD

a.

Remove the 16 bolts, 2 gaskets and intake manifold.


b.

Remove the 9 bolts, No. 1 intake manifold and gasket.


c.

Remove the 9 bolts, No. 2 intake manifold and gasket.


Hide 11228A 57.INSTALL CYLINDER HEAD COVER INSULATOR LH (w/ DPF)

Hide 11227 58.INSTALL CYLINDER HEAD COVER INSULATOR RH (w/ DPF)

Hide 59.INSTALL NO. 2 FUEL PUMP BRACKET (w/ DPF)

a.

Install the No. 2 fuel pump bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11214 60.INSTALL NOZZLE HOLDER GASKET LH (w/o DPF)

Hide 11202 61.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/o DPF)

Hide 23681E 62.INSTALL NOZZLE HOLDER SEAL LH (w/o DPF)

Hide 11213 64.INSTALL NOZZLE HOLDER GASKET RH (w/o DPF)

Hide 11201 65.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/o DPF)

Hide 23681D 66.INSTALL NOZZLE HOLDER SEAL RH (w/o DPF)

Hide 12108A 67.INSTALL OIL FILLER CAP GASKET

Hide 12108 68.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 11381A 71.INSTALL REAR CRANKSHAFT OIL SEAL

a.
U162926E02
1.198,1.271 0.75,0.469 0.75,0.469 0.563,0.469 true 0.219,0.385 0.521,0.542 0.302,0.156 10 false SST 1.875,2.115 2.031,2.281 0.156,0.167 10 false A

Place the oil seal retainer on wooden blocks.


b.

Using SST and a hammer, tap in a new oil seal as shown in the illustration.

SST
09223-56010  

Standard depth A:

2.7 to 3.7 mm (0.106 to 0.147 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the seal at an angle.




Hide 11381 72.INSTALL REAR ENGINE OIL SEAL RETAINER

Hide 15411 74.INSTALL INLET OIL PUMP PIPE

a.

Apply a light coat of engine oil to a new O-ring, and install it to the inlet oil pump pipe.


b.

Install the inlet oil pump pipe with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12121 75.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.

Install the No. 1 oil pan baffle plate with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 76.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

Hide 15104 77.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 78.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12101K 79.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 15609 81.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.
U163097E02
1.458,1.333 1.458,1.604 false 1.375,1.688 1.563,1.844 0.188,0.156 10 false *1

Apply a light coat of engine oil to 2 new O-rings, and set them to the oil filter bracket.

Text in Illustration
*1 New O-Ring


b.

Install the oil filter bracket with the 3 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 15690 83.INSTALL OIL COOLER RELIEF VALVE ASSEMBLY

a.

Install a new gasket and the oil cooler relief valve.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 83520 85.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 11348 86.INSTALL TIMING GEAR COVER SPACER (w/ Intercooler)

Hide 13471 87.INSTALL CRANKSHAFT PULLEY

NOTICE:

This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.


a.
A174866E04
2.521,2.552 1.448,2.552 true 1.125,2.188 1.313,2.188 1.313,2.188 1.51,1.625 true 0.917,2.104 1.125,2.323 0.208,0.219 10 true *1 1.229,2.479 1.417,2.635 0.188,0.156 10 false *2

Align the crankshaft pulley and the crankshaft knock pin, and temporarily install the crankshaft pulley with the 3 bolts.

Text in Illustration
*1 Service Hole
*2 Protrusion


b.

Install the 2 bolts to the bolt holes of the crankshaft rear side.


c.

Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the right of bottom dead center.


d.

Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.


e.
U163140E02
1.729,0.771 1.729,0.365 1.729,0.365 1.167,0.365 true 1.958,1.323 2.219,1.583 2.219,1.583 3.063,1.583 true 1.479,1.302 1.219,1.563 1.219,1.563 0.385,1.563 true 1.271,0.115 1.427,0.281 0.156,0.167 10 false 1 2.604,1.333 2.76,1.5 0.156,0.167 10 false 2 0.479,1.302 0.635,1.469 0.156,0.167 10 false 3 1.542,0.115 1.698,0.281 0.156,0.167 10 false 4 2.875,1.333 3.031,1.5 0.156,0.167 10 false 5 0.75,1.302 0.906,1.469 0.156,0.167 10 false 6

Uniformly tighten the 3 bolts in 2 passes in the order shown in the illustration.

Torque:
115 N*m (1168 kgf*cm, 84 ft.*lbf)


f.

Remove the service bolt.


Hide 15778 88.CONNECT NO. 2 OIL COOLER HOSE

a.

Align the white paint marks on the oil cooler hose and oil filter bracket and connect the hose. Then connect the other side to the water pump and attach the oil cooler hose to the clamp.

NOTICE:

Make sure to maintain a space between the oil cooler hose and crankshaft pulley, and the oil cooler hose and V-ribbed belt idler pulley.



Hide 15777 89.CONNECT NO. 1 OIL COOLER HOSE

a.

Face the pink paint mark on the oil cooler hose toward the front side of the engine and connect the hose to the oil filter bracket. Then connect the other side to the water pump.

NOTICE:

Make sure to maintain a space between the oil cooler hose and crankshaft pulley.