Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2017.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255049 ENGINE ASSEMBLY A

3UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53301 5.REMOVE HOOD SUB-ASSEMBLY

a.
A174152

Remove the 2 hood support bolts and disconnect the hood supports.

CAUTION:

Remove the hood support assembly while supporting the hood by hand.



b.

Remove the 4 bolts and hood.


Hide 55781E 6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53739A 8.REMOVE FRONT FENDER APRON SEAL REAR LH

Hide 53736G 9.REMOVE FRONT FENDER APRON SEAL FRONT RH

Hide 53738A 10.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 51405A 11.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A238241

Remove the 10 bolts and No. 1 engine under cover.


Hide 51442 12.REMOVE NO. 2 ENGINE UNDER COVER

a.
A178462

Remove the 2 bolts and No. 2 engine under cover.


Hide 32917 16.REMOVE TRANSMISSION OIL COOLER AIR DUCT

Hide 53294C 17.REMOVE RADIATOR SIDE DEFLECTOR LH

Hide 11209 18.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A174196E06
1.719,0.458 1.865,0.458 1.865,0.458 2.177,0.583 false 1.781,0.156 1.958,0.156 1.958,0.156 2.5,0.458 false 0.438,2.917 0.563,2.917 false 0.896,2.781 1.49,3.031 1.49,3.031 1.49,3.135 false 1.542,0.375 1.74,0.563 0.198,0.188 10 false *2 1.583,0.094 1.74,0.281 0.156,0.188 10 false *1 1.406,3.146 1.594,3.323 0.188,0.177 10 false *4 0.25,2.833 0.427,3.01 0.177,0.177 10 false *3

Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

Text in Illustration
*1 Bracket
*2 Hook
*3 Pin
*4 Grommet


Hide 17700 20.REMOVE AIR CLEANER ASSEMBLY

a.
A174195

Remove the 3 bolts and air cleaner.


Hide 16571C 21.REMOVE NO. 1 RADIATOR HOSE

Hide 16572D 22.REMOVE NO. 2 RADIATOR HOSE

Hide 23801P 25.DISCONNECT FUEL MAIN AND RETURN HOSE

a.
A238245

Remove the fuel pipe clamp.


b.

Disconnect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 26.DISCONNECT WIRE HARNESS AND HOSE

a.
A178804

Disconnect the purge line hose.


b.
A370858E02
0.135,0.167 0.458,0.385 0.323,0.219 10 true *A 0.135,2.563 0.469,2.802 0.333,0.24 10 true *B

Remove the heater hose.


c.

Disconnect the clamp and ECM connector.

Text in Illustration
*A w/o Rear Heater
*B w/ Rear Heater

HINT:

Refer to the following procedures to disconnect the ECM connector (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>ECM>REMOVAL).



d.
A370859

Disconnect the 5 connectors and clip from the connector holder block.


e.
A177630

w/ Secondary Air Injection System:

i.

Disconnect the 2 air pump connectors and 3 clamps.


ii.

Remove the nut and connector bracket.


iii.

Remove the bolt and disconnect the ground wire.


iv.

Disconnect the 2 air injection system hoses.



f.
A239140

w/o Secondary Air Injection System:

i.

Remove the bolt and disconnect the ground wire.



g.
A174200

w/ Secondary Air Injection System:

Disconnect the 4 air injection control driver connectors and clamp.


h.
A361470

Remove the nut and disconnect the wire from the positive (+) battery cable.


i.

Disconnect the cable from the positive (+) battery terminal.


j.

Remove the bolt and disconnect the ground wire from the body.


k.

Disconnect the clamp.


l.

Remove the nut and disconnect the wire and 2 clips from the engine room junction block.


m.

Disconnect the 2 connectors and 2 clips from the engine room junction block.


n.
A370872

Disconnect the 2 connectors and 2 clamps.


o.
A366747

w/ Winch:

Detach the wire harness clamp, remove the nut and disconnect the ground wire from the wire harness clamp bracket.


Hide 88320 27.DISCONNECT COOLER COMPRESSOR ASSEMBLY

Hide 44310 28.DISCONNECT VANE PUMP ASSEMBLY

Hide 17420 31.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 17450B 32.REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 17410 33.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 11452 34.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A174205

Disconnect the wire harness clamp.


b.

Remove the dipstick.


c.

Remove the bolt and dipstick guide.


d.

Remove the O-ring from the dipstick guide.


Hide 37140 35.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 36.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 37117 37.REMOVE PROPELLER SHAFT HEAT INSULATOR

Hide 17168 39.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 40.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17167 42.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 43.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 12371 47.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Only perform this procedure when replacement of the engine mounting insulator is necessary.


a.
C172399

Remove the 2 bolts and front engine mounting insulator RH.


b.

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 32101 48.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E02
1.359,1.727 1.661,1.883 0.302,0.156 10 SST 0.829,1.22 0.829,1.812 0.829,1.812 1.312,1.812 false 1.076,1.054 1.076,1.812 false

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A238248

Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.


Hide 32907A 49.DISCONNECT OIL COOLER PIPE ASSEMBLY

a.
A174185

Remove the 2 bolts and disconnect the oil cooler pipe.


Hide 50.REMOVE WATER PIPE AND HOSE SUB-ASSEMBLY

a.
A184532

Remove the 2 bolts and disconnect the hose. Then remove the water pipe and hose.


Hide 51.REMOVE ENGINE ASSEMBLY

a.
A236996

Install 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Engine hanger 12281-38150
Bolt 90119-14120



b.
A150148E05
0.635,1.135 1.958,0.75 1.958,0.75 1.885,0.979 false 1.188,0.792 1.542,0.375 1.542,0.375 1.688,0.375 false 1.063,1.427 1.271,1.604 0.208,0.177 10 false *2 2.01,0.656 2.198,0.823 0.188,0.167 10 false *1 1.729,0.281 1.958,0.5 0.229,0.219 10 false *a

Attach an engine sling device and hang the engine with a chain block.

Text in Illustration
*1 Engine Hanger
*2 ENGINE
*a 50° or less

NOTICE:

When hanging the engine, make sure to hang the engine with the sling device's hanging angle at 50° or less. If not, the engine or engine hangers may be damaged.



c.
A178464E05
0.063,0.042 0.448,0.281 0.385,0.24 10 true *A 0.063,2.344 0.427,2.594 0.365,0.25 10 true *B

Remove the 4 engine mounting insulator bolts.

Text in Illustration
*A RH
*B LH


d.

Lift the engine out from the vehicle slowly and carefully.

NOTICE:
·

Make sure the engine is clear of all wiring, hoses and cables.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




Hide 52.INSTALL ENGINE ON ENGINE STAND

a.

Install the engine onto an engine stand with bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 12362A 53.REMOVE FRONT ENGINE MOUNTING INSULATOR LH

a.
A163787

Remove the nut and mounting insulator.


Hide 12361 54.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A174119

Remove the nut and mounting insulator.


Hide 12316A 55.REMOVE NO. 2 FRONT ENGINE MOUNTING BRACKET LH

a.
A178524

Remove the bolt and No. 2 front engine mounting bracket LH.