Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM38G0E _58 Vehicle Interior _100612 SEAT BELT _0467501 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly blinks or turns off the front passenger seat belt warning light on the combination meter assembly in accordance with the state of the front seat belt set (for front passenger side) and occupant detection sensor (front seat cushion pad (for front passenger side)).

WIRING DIAGRAM

B582860E06
0.49,1.354 1.688,2.146 1.198,0.792 10 false Combination Meter Assembly 3.115,1.385 4.781,2.135 1.667,0.75 10 false Main Body ECU (Multiplex Network Body ECU) 4.583,0.792 5.135,1.156 0.552,0.365 10 false CXPI 5.094,0.594 5.646,0.958 0.552,0.365 10 false 22 5.115,0.792 5.667,1.156 0.552,0.365 10 false A 5.094,2.885 5.646,3.25 0.552,0.365 10 false 5F 5.094,4.542 5.646,4.906 0.552,0.365 10 false 5F 5.094,4.323 5.646,4.688 0.552,0.365 10 false 29 5.073,2.667 5.625,3.031 0.552,0.365 10 false 11 3.938,2.865 4.49,3.229 0.552,0.365 10 false S29 3.938,3.406 4.49,3.771 0.552,0.365 10 false S29 3.938,3.969 4.49,4.333 0.552,0.365 10 false S29 3.948,4.521 4.5,4.885 0.552,0.365 10 false S29 2.385,4.521 2.938,4.885 0.552,0.365 10 false A 2.385,3.979 2.938,4.344 0.552,0.365 10 false A 2.385,3.771 2.938,4.135 0.552,0.365 10 false 3 2.385,4.333 2.938,4.698 0.552,0.365 10 false 1 0.615,3.885 1.865,4.729 1.25,0.844 10 false Occupant Detection Sensor 0.281,4.969 1.854,6.052 1.573,1.083 10 false Front Seat Cushion Pad (for front passenger side) 3.708,3.865 4.26,4.229 0.552,0.365 10 false E 3.708,3.302 4.26,3.667 0.552,0.365 10 false E 3.708,2.74 4.26,3.104 0.552,0.365 10 false + 3.708,4.417 4.26,4.781 0.552,0.365 10 false + 2.542,4.958 4.021,5.781 1.479,0.823 10 false Front Seat Belt Set (for front passenger side) 5.385,4.958 6.833,5.698 1.448,0.74 10 false Power Distribution Box Assembly 4.99,5.979 6.76,6.396 1.771,0.417 10 false : CAN Communication Line 4.99,6.354 6.896,6.698 1.906,0.344 10 false : CXPI Communication Line 4,2.667 4.552,3.031 0.552,0.365 10 false 1 4.042,4.344 4.594,4.708 0.552,0.365 10 false 4 4.042,3.24 4.594,3.604 0.552,0.365 10 false 2 4.031,3.792 4.583,4.156 0.552,0.365 10 false 5 6.469,2.615 7.021,2.979 0.552,0.365 10 false IC 0.271,5.938 1.958,6.135 1.688,0.198 10 false *1: for RHD 0.26,6.271 1.948,6.469 1.688,0.198 10 false *2: for LHD 4.313,2.875 4.865,3.24 0.552,0.365 10 false Q46 4.313,3.417 4.865,3.781 0.552,0.365 10 false Q46 4.313,3.979 4.865,4.344 0.552,0.365 10 false Q46 4.323,4.521 4.875,4.885 0.552,0.365 10 false Q46 4.406,2.677 4.958,3.042 0.552,0.365 10 false 1 4.417,3.24 4.969,3.604 0.552,0.365 10 false 2 4.406,3.802 4.958,4.167 0.552,0.365 10 false 5 4.417,4.344 4.969,4.708 0.552,0.365 10 false 4 4.01,3.073 4.323,3.271 0.313,0.198 10 false *1 4.375,3.083 4.688,3.281 0.313,0.198 10 false *2 4,3.635 4.313,3.833 0.313,0.198 10 false *1 4,4.74 4.313,4.938 0.313,0.198 10 false *1 3.99,4.188 4.302,4.385 0.313,0.198 10 false *1 4.375,3.625 4.688,3.823 0.313,0.198 10 false *2 4.375,4.177 4.688,4.375 0.313,0.198 10 false *2 4.396,4.75 4.708,4.948 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



HINT:
·

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>OPERATION CHECK

·

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



PROCEDURE

1.READ VALUE USING GTS (PASSENGER SEAT BUCKLE SWITCH STATUS / PASSENGER SEAT OCCUPANT SENSOR STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Passenger Seat Buckle Switch Status Front passenger side seat belt buckle switch status Set, Unset, Unknown Set: Front passenger seat belt fastened
Unset: Front passenger seat belt not fastened
Unknown: Data is not determined
-
Passenger Seat Occupant Sensor Status Front passenger seat occupant detection sensor status OFF, ON, Unknown OFF: Front passenger seat not occupied
ON: Front passenger seat occupied
Unknown: Data is not determined
-
Body Electrical > Power Distribution Box > Data List
Tester Display
Passenger Seat Buckle Switch Status
Passenger Seat Occupant Sensor Status
50003 475 1400,1401
OK:

The GTS display changes correctly in response to the front passenger seat belt and front passenger seat condition.



Result:
Result Proceed to
OK A
NG (Passenger Seat Buckle Switch Status) B
NG (Passenger Seat Occupant Sensor Status) C



A

B

2.INSPECT FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE)

C

4.INSPECT FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE)
2.INSPECT FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE)

OK

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE))

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the S29*1 or Q46*2 front seat belt set (for front passenger side) connector.

*1: for RHD

*2: for LHD



b.

Disconnect the 5F power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(Q46)Location & Routing

Click Connector(Q46)Seat>Floor Wire>Front Seat Belt Set RH

Q46-1 (+) - 5F-11 Always Below 1 Ω
Q46-2 (E) - Body ground Always Below 1 Ω
Q46-1 (+) or 5F-11 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(S29)Location & Routing

Click Connector(S29)Seat>No. 2 Floor Wire>Front Seat Belt Set LH

S29-1 (+) - 5F-11 Always Below 1 Ω
S29-2 (E) - Body ground Always Below 1 Ω
S29-1 (+) or 5F-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE)

OK

5.INSPECT OCCUPANT DETECTION SENSOR (FRONT SEAT CUSHION PAD (FOR FRONT PASSENGER SIDE))

NG

REPLACE FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE)

5.INSPECT OCCUPANT DETECTION SENSOR (FRONT SEAT CUSHION PAD (FOR FRONT PASSENGER SIDE))

OK

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

NG

REPLACE OCCUPANT DETECTION SENSOR (FRONT SEAT CUSHION PAD (FOR FRONT PASSENGER SIDE))

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT BELT SET (FOR FRONT PASSENGER SIDE) - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the S29*1 or Q46*2 front seat belt set (for front passenger side) connector.

*1: for RHD

*2: for LHD



b.

Disconnect the 5F Power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(Q46)Location & Routing

Click Connector(Q46)Seat>Floor Wire>Front Seat Belt Set RH

Q46-4 (+) - 5F-29 Always Below 1 Ω
Q46-5 (E) - Body ground Always Below 1 Ω
Q46-4 (+) or 5F-29 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(S29)Location & Routing

Click Connector(S29)Seat>No. 2 Floor Wire>Front Seat Belt Set LH

S29-4 (+) - 5F-29 Always Below 1 Ω
S29-5 (E) - Body ground Always Below 1 Ω
S29-4 (+) or 5F-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR