Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0469186 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P030000  Random/Multiple Cylinder Misfire Detected  P030027  Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold  P030085  Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range  P030100  Cylinder 1 Misfire Detected  P030200  Cylinder 2 Misfire Detected  P030300  Cylinder 3 Misfire Detected  P030400  Cylinder 4 Misfire Detected  P030500  Cylinder 5 Misfire Detected  P030600  Cylinder 6 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and the crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P030000 Random/Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0300
P030027 Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold An emission deteriorationmisfire occurs (2 tripdetection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on SAE: -
P030085 Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range A misfire occurs that maydamage the three-waycatalytic converter (2 tripdetection logic).
·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: -
P030100 Cylinder 1 Misfire Detected Misfiring of the No. 1 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0301
P030200 Cylinder 2 Misfire Detected Misfiring of the No. 2 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0302
P030300 Cylinder 3 Misfire Detected Misfiring of the No. 3 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0303
P030400 Cylinder 4 Misfire Detected Misfiring of the No. 4 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0304
P030500 Cylinder 5 Misfire Detected Misfiring of the No. 5 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0305
P030600 Cylinder 6 Misfire Detected Misfiring of the No. 6 cylinder occurs and either of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
SAE: P0306

When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).

·

An excessive number of misfires (approximately 72 to 85 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediately detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

7.

Start the engine.

8.

Read the misfire count of each cylinder (Misfire Count Cylinder #1 to Misfire Count Cylinder #6) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

9.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


10.

Check whether misfires have occurred by checking for DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.


11.

Record the DTC(s), freeze frame data and misfire counts.

12.

Turn the ignition switch off and wait for at least 30 seconds.

13.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).


WIRING DIAGRAM

Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P010012

Refer to Fuel Injector Circuit.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>Fuel Injector Circuit

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, the following factors can be considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #6).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

For 6 cylinder engine, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine speed. If misfires occur only in high engine speed areas, only DTC P030000 is set.

In the event of DTC P030000 being present, perform the following operations:

(a)

Clear the DTCs.

(b)

Start the engine and conduct the confirmation driving pattern.

(c)

Read the misfiring counts of each cylinder or DTC(s) using the GTS.

(d)

Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.

(e)

After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P030000 is not set.


·

When one of Short FT B1S1, Long FT B1S1, Short FT B2S1 or Long FT B2S1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or higher).

·

When Coolant Temperature in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Turn the ignition switch to ON.


b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output A
DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 and other DTCs are output B


HINT:

If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>1GR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

PCV valve and hose are correctly connected and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Turn the ignition switch to ON.


b.

Read and note the Misfire RPM and Misfire Load values.

Powertrain > Engine > Data List
Tester Display
Misfire RPM
Misfire Load
50003 372 146,152
HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
4.READ VALUE USING GTS (CATALYST OT MISFIRE FUEL CUT)
a.

Turn the ignition switch to ON.


b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Catalyst OT Misfire Fuel Cut
50003 372 154
Result:
Data List Result Proceed to
Catalyst OT Misfire Fuel Cut Avail A
Not Avl B




A

5.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT)

B

6.READ VALUE USING GTS (MISFIRE COUNT)
5.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT FUEL CUT)
a.

Turn the ignition switch to ON.


b.

Perform the Active Test.

Powertrain > Engine > Active Test
Tester Display
Prohibit the Catalyst OT Misfire Prevent Fuel Cut
50004 372 42003
NOTICE:

When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.



Result:
Proceed to
NEXT



NEXT

6.READ VALUE USING GTS (MISFIRE COUNT)
6.READ VALUE USING GTS (MISFIRE COUNT)
a.

Start the engine and warm it up.


b.

Allow the engine to idle.


c.

Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #6 displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

Powertrain > Engine > Data List
Tester Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
Misfire Count Cylinder #5
Misfire Count Cylinder #6
50003 372 411,412,413,414,415,416
i.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM And Misfire Load)" procedures above [A].


ii.

Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #6 or DTCs displayed on the GTS [B].



Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is less than 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.




A

7.INSPECT SPARK PLUG

B

17.CHECK INTAKE SYSTEM
7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.CHECK FOR SPARKS (SPARK TEST)

NG

8.CHECK FOR SPARKS (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND/OR #60)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.CHECK TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND/OR #60)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C92)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C92-86 (#10) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-109 (#20) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-85 (#30) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-108 (#40) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-84 (#50) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-107 (#60) - C92-43 (E02) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

11.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

13.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

13.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (COOLANT TEMP)

NG

34.CHECK FUEL LINE
14.READ VALUE USING GTS (COOLANT TEMP)
a.

Turn the ignition switch to ON.


b.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

15.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.

Powertrain > Engine > Data List
Tester Display
Target Idle Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 1095,215,205

c.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Shift lever position: N
A/C: Off
Engine Speed: 3000 rpm
Between 18.3 gm/sec and 25.8 gm/sec



Result:
Proceed to
OK
NG



OK

16.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
16.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A385296C01
1.26,0.813 1.5,0.365 true 1.24,1.083 1.5,0.365 true 1.969,1.458 2.188,0.875 true 1.969,1.448 2.167,1.219 true 2.854,3.271 3.125,2.844 true 2.865,3.229 3.052,2.833 true 2.865,3.25 3.042,2.615 true 2.208,2.51 2.479,2.135 true 2.219,2.906 2.469,2.135 true 1.531,0.208 1.844,0.406 0.313,0.198 10 false *1 1.854,1.5 2.167,1.698 0.313,0.198 10 false *1 2.719,3.25 3.031,3.448 0.313,0.198 10 false *1 2.448,1.99 2.76,2.188 0.313,0.198 10 false *1
*1 Timing Mark


a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing sprockets are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

NG

27.CHECK ENGINE MECHANICAL SYSTEM
17.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>1GR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

18.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

18.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

19.READ VALUE USING GTS (COOLANT TEMPERATURE)

NG

34.CHECK FUEL LINE
19.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Turn the ignition switch to ON.


b.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

20.READ VALUE USING GTS (MASS AIR FLOW SENSOR)

NG

20.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Start the engine.


b.

Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
Coolant Temperature
50003 372 211,215,205

c.

Read Mass Air Flow Sensor with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Mass Air Flow Sensor Shift lever position: N
A/C: Off
Engine Speed: 3000 rpm
Between 18.3 gm/sec and 25.8 gm/sec



Result:
Proceed to
OK
NG



OK

21.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
21.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
A385296C01
1.26,0.813 1.5,0.365 true 1.24,1.083 1.5,0.365 true 1.969,1.458 2.188,0.875 true 1.969,1.448 2.167,1.219 true 2.854,3.271 3.125,2.844 true 2.865,3.229 3.052,2.833 true 2.865,3.25 3.042,2.615 true 2.208,2.51 2.479,2.135 true 2.219,2.906 2.469,2.135 true 1.531,0.208 1.844,0.406 0.313,0.198 10 false *1 1.854,1.5 2.167,1.698 0.313,0.198 10 false *1 2.719,3.25 3.031,3.448 0.313,0.198 10 false *1 2.448,1.99 2.76,2.188 0.313,0.198 10 false *1
*1 Timing Mark


a.

Remove the cylinder head cover sub-assembly and cylinder head cover sub-assembly LH.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets are aligned with the timing marks of the bearing cap as shown in the illustration.

HINT:

If the timing marks are not as shown, turn the crankshaft one revolution clockwise.


OK:

The timing marks on the camshaft timing gear assemblies and camshaft timing sprockets are aligned as shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

22.INSPECT SPARK PLUG

NG

27.CHECK ENGINE MECHANICAL SYSTEM
22.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

23.CHECK FOR SPARKS (SPARK TEST)

NG

23.CHECK FOR SPARKS (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

24.CHECK CYLINDER COMPRESSION PRESSURE
24.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

25.CHECK TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND/OR #60)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

25.CHECK TERMINAL VOLTAGE (#10, #20, #30, #40, #50 AND/OR #60)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(C92)Location & Routing

Click Connector(C92)Engine Compartment>Connecting Wire / Cooling Fan Wire / Engine Wire / Fuel Pump Motor Wire / No. 1 Connecting Wire / No. 10 Engine Wire / No. 2 Connecting Wire / No. 3 Connecting Wire / No. 4 Connecting Wire / Sensor Wire / Turbocharger Wire>ECM

C92-86 (#10) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-109 (#20) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-85 (#30) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-108 (#40) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-84 (#50) - C92-43 (E02) Ignition switch ON 11 to 14 V
C92-107 (#60) - C92-43 (E02) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

27.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

28.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

28.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 is output)
B




A

B

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

30.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
30.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 is output)
B




A

END

B

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.



Result:
Proceed to
OK
NG



OK

32.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Turn the ignition switch to ON.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait for at least 30 seconds.


d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 or P030600.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

g.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300, P030400, P030500 and/or P030600 is output)
B




A

END

B

34.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE