Home › Engine / Hybrid System › F33A-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2021.07
RM38G0E _51 Engine / Hybrid System _106329 F33A-FTV ENGINE CONTROL _0484871 ECD SYSTEM(w/ DPF) C

F33A-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P20CF00  Exhaust Aftertreatment Fuel Injector "A" Stuck Open  


DESCRIPTION

Refer to DTC P200C4B (Click here Engine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P200C4B).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note
P20CF00 Exhaust Aftertreatment Fuel Injector "A" Stuck Open AF (O2) Lambda B1S1 is less than 0.85 for a certain time while the engine is running.
(1 trip detection logic)
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

Fuel filter element assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on SAE Code: P20CF

Related Data List
DTC No. Data List
P20CF00
·

A/F (O2) Lambda B1S1

·

Exhaust Temperature B1S2 (w/ Urea SCR System)

·

Exhaust Temperature B1S3 (w/o Urea SCR System)



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CF00 PM forced regeneration

MONITOR DESCRIPTION

The ECM monitors the air fuel ratio to detect whether the exhaust fuel addition injector assembly is stuck open.

If the air fuel ratio becomes too rich, the ECM determines that the exhaust fuel addition injector assembly is stuck open, illuminates the MIL and limits engine output.

HINT:

The No. 1 nitrogen oxides sensor has an air fuel ratio sensor function (w/ Urea SCR System).


A248903E09
2.969,1.615 2.573,2.354 2.573,2.354 2.49,2.354 false 0.177,0.167 1.688,0.469 1.51,0.302 10 false Malfunction Detection: 0.25,1.031 1.333,1.583 1.083,0.552 10 false A/F (O2) Lambda B1S1 3.854,2.031 4.927,2.365 1.073,0.333 10 false MIL Goes On 1.885,2.271 2.615,2.51 0.729,0.24 10 false Abnormal 5.552,1.031 6.656,1.323 1.104,0.292 10 false Normal 5.75,1.49 7.115,1.927 1.365,0.438 10 false P20CF00 Threshold 1.792,0.604 2.219,0.875 0.427,0.271 10 false Lean 1.802,1.354 2.208,1.615 0.406,0.26 10 false Rich

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM and performing "LEARNING VALUES WRITE", select "PM Regenerate Mode" using Utility of the GTS to perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P20CF00)
a.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

b.

Read the DTCs.

Result:
Result Proceed to
DTC P20CF00 is output A
DTC P20CF00 and other DTCs are output B


HINT:
·

w/ Urea SCR System:

When DTC P20CF00 and following DTCs are output, uncombusted fuel adhesion to the No. 1 nitrogen oxides sensor due to No. 1 nitrogen oxides sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.

·

w/o Urea SCR System:

When DTC P20CF00 and following DTCs are output, uncombusted fuel adhesion to the air fuel ratio sensor due to air fuel ratio sensor malfunction, fuel leaks, insufficient combustion due to parts malfunction (intake, exhaust or injection system), or an exhaust fuel addition injector assembly wiring malfunction is suspected as a cause. Therefore, diagnose the following DTCs first.

·

w/ Urea SCR System:

DTCs for the No. 1 nitrogen oxides sensor are DTC P013013, P220011, P220012, P220013, P220512 and P220514.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P013013

·

w/o Urea SCR System:

DTCs for the air fuel ratio sensor are DTC P223711, P223712, P223713, P223716, P223717, P225111 and P225112.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P223711

·

A DTC for fuel leakage is DTC P009300.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P009300

·

DTCs for the exhaust fuel addition injector assembly wiring malfunction are DTC P20CB12 and P20CB14.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P20CB12

·

A DTC for EGR valve flow malfunction is DTC P040000.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P040000

·

A DTC for EGR valve stuck open is DTC P040371.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P040371





A

2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)

B

7.GO TO DTC CHART
2.CHECK FOR WHITE SMOKE (WHITE SMOKE AND ODOR)
NOTICE:

If a fuel odor is noted from the white smoke during the inspection, fuel leaks from the exhaust fuel addition injector assembly are suspected.


a.

Disconnect the cable from the negative (-) battery terminal or remove the EFI MAIN NO. 1 fuse from the engine room relay block and junction block assembly for more than 1 minute.


b.

Start the engine and race it to 3000 rpm several times.


c.

Check for white smoke in the exhaust gas. If found, check for a fuel odor or the smell of burning oil.

Result:
Result Proceed to
White smoke and a fuel odor are present (w/ Urea SCR System). A
White smoke and a fuel odor are present (w/o Urea SCR System). B
White smoke and a smell of burning oil are present. C
Except above D




A

3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)

B

8.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)

C

9.CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE

D

11.CHECK FUEL INJECTION SYSTEM
3.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)
a.

Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Lambda B1S1 and Exhaust Temperature B1S2 and Fr-NOx Sensor NOx Active Status (SCU).

Powertrain > Engine > Data List
Tester Display
A/F (O2) Lambda B1S1
Exhaust Temperature B1S2
Fr-NOx Sensor A/F Active Status (SCU)
50003 372 1161,1134,1044

b.

Drive the vehicle until the value of Exhaust Temperature B1S2 becomes 200°C (392°F) or more to activate the Fr-NOx Sensor NOx Active Status (SCU).


c.

Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

A427297E05
5.969,1.719 6.313,1.104 6.313,1.104 6.448,1.104 true 5.188,2.823 5.344,3.073 5.344,3.073 5.479,3.073 true 0.344,1.875 2.49,2.073 2.146,0.198 10 false A/F (O2) Lambda B1S1 1.865,2.469 4.01,2.667 2.146,0.198 10 false 1.0 4.281,0.708 7.156,0.927 2.875,0.219 10 false After No. 1 Nitrogen Oxides Sensor Activation 3.5,0.115 5.646,0.313 2.146,0.198 10 false No. 1 Nitrogen Oxides Sensor Starter Operation 6.594,1.01 7.156,1.292 0.563,0.281 10 false Normal 5.563,2.99 6.417,3.302 0.854,0.313 10 false Abnormal

HINT:
·

The No. 1 nitrogen oxides sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

·

Perform diagnosis when the No. 1 nitrogen oxides sensor is operating and active.

·

Normal condition in the illustration is only an example. "A/F (O2) Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.



Result:
Result Proceed to
There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
Except above B


HINT:

If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.




A

4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

11.CHECK FUEL INJECTION SYSTEM
4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
5.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Clean the fuel filter case and replace the fuel filter element assembly.

Click hereEngine / Hybrid System>F33A-FTV (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


c.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

11.CHECK FUEL INJECTION SYSTEM
7.GO TO DTC CHART
a.

Perform inspection and repair of relevant DTCs.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.PERFORM CONFIRMATION DRIVING PATTERN (WHITE SMOKE AND SENSORY INSPECTION)
a.

Enter the following menus: Powertrain / Engine / Data List / A/F (O2) Lambda B1S1 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
A/F (O2) Lambda B1S1
Exhaust Temperature B1S3
50003 372 1161,1135

b.

Drive the vehicle until the value of Exhaust Temperature B1S3 becomes 300°C (572°F) or more to activate the air fuel ratio sensors.


c.

Check that there is no problem on driving performance such as hesitation, knocking, rough idling, insufficient power and acceleration stumbling, or white smoke in emissions.

A427297E06
5.969,1.719 6.313,1.104 6.313,1.104 6.448,1.104 true 5.188,2.823 5.344,3.073 5.344,3.073 5.479,3.073 true 0.719,1.906 3.115,2.302 2.396,0.396 10 false A/F (O2) Lambda B1S1 1.865,2.469 4.01,2.667 2.146,0.198 10 false 1.0 4.281,0.708 7.156,0.927 2.875,0.219 10 false After Air Fuel Ratio Sensor Activation 3.5,0.115 6.344,0.542 2.844,0.427 10 false Air Fuel Ratio Sensor Starter Operation 6.594,1.01 7.156,1.292 0.563,0.281 10 false Normal 5.563,2.99 6.417,3.302 0.854,0.313 10 false Abnormal

HINT:
·

The air fuel ratio sensor does not operate until the vehicle has been driven for a period of time with an exhaust gas temperature of 200°C (392°F) or more.

·

Perform diagnosis when the air fuel ratio sensor is operating and active.

·

Normal condition in the illustration is only an example. "A/F (O2) Lambda B1S1" changes depending on driving conditions. If it changes at the range more than 1.0, it is normal.



Result:
Result Proceed to
There is no problem with driving performance such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, but excessive white smoke is present in the exhaust gas A
Except above B


HINT:

If white smoke is present in the exhaust gas without any driving performance problems such as hesitation, knocking, rough idling, insufficient power or acceleration stumbling, fuel injected due to a malfunction in the exhaust fuel addition injector assembly is the suspected cause of the white smoke.




A

4.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

B

11.CHECK FUEL INJECTION SYSTEM
9.CHECK TURBOCHARGER OIL LEAK AND WHITE SMOKE
a.

Check for oil leaks and white smoke from the turbocharger sub-assembly and perform any necessary repairs.

Click hereEngine / Hybrid System>F33A-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>Turbocharger Oil Leak and White Smoke

HINT:

Other than a malfunction of the turbocharger sub-assembly, exhaust valve stem oil leaks are suspected.



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


c.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>F33A-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
NEXT



NEXT

END

11.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CHECK INTAKE/EXHAUST SYSTEM
12.CHECK INTAKE/EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

13.CHECK AFTER TREATMENT CONTROL SYSTEM
13.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED