Home › ADAS / AD › ADVANCED DRIVER ASSISTANCE SYSTEM › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2021.07
RM38G0E _95 ADAS / AD _100650 ADVANCED DRIVER ASSISTANCE SYSTEM _0469138 DYNAMIC RADAR CRUISE CONTROL SYSTEM T

ADVANCED DRIVER ASSISTANCE SYSTEM  DYNAMIC RADAR CRUISE CONTROL SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history (RoB). Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history (RoB) for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA>DRIVING ADJUSTMENT




HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.

·

Determine the problem symptoms, then perform the respective inspection procedures.

·

By using the vehicle control history (RoB), various control parameter history can be checked.



Dynamic Radar Cruise Control System
Symptom Suspected Area Link
The dynamic radar cruise control system cannot be turned on using the cruise control main switch CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
Cruise main indicator light circuit Click here
Forward recognition camera Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
The dynamic radar cruise control mode cannot be changed between vehicle-to-vehicle distance control mode and constant speed control mode CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
The vehicle-to-vehicle distance cannot be changed CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
Forward recognition camera Click here
Vehicle speed setting cannot be performed (in constant speed control mode) Fail-safe chart Click here
CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
Stop light switch circuit Click here
Vehicle speed setting cannot be performed (in constant speed control mode) SFI system (for 1GR-FE) Click here
SFI system (for V35A-FTS) Click here
ECD system (for F33A-FTV) w/ DPF:Click here
w/o DPF:Click here
Electronically controlled brake system Click here
Forward recognition camera Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Vehicle speed setting cannot be performed (in vehicle-to-vehicle distance control mode) Front Radar Sensor Temporary Unavailable (Optical Axis Misalignment) history Click here
Fail-safe chart Click here
Forward recognition camera is temporarily unavailable Click here
Millimeter wave radar sensor assembly is dirty Click here
Millimeter wave radar sensor assembly beam axis not adjusted
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.


Triangle Target:Click here
Flat Surface Target:Click here
Driving Adjustment:Click here
Vehicle speed setting cannot be performed (in vehicle-to-vehicle distance control mode) CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
SFI system (for 1GR-FE) Click here
SFI system (for V35A-FTS) Click here
ECD system (for F33A-FTV) w/ DPF:Click here
w/o DPF:Click here
Vehicle speed setting cannot be performed (in vehicle-to-vehicle distance control mode) Electric parking brake system Click here
Electronically controlled brake system Click here
Millimeter wave radar sensor assembly Click here
Forward recognition camera Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Control of vehicle speed by the dynamic radar cruise control system is canceled (in constant speed control mode) Fail-safe chart Click here
CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
Stop light switch circuit Click here
SFI system (for 1GR-FE) Click here
SFI system (for V35A-FTS) Click here
ECD system (for F33A-FTV) w/ DPF:Click here
w/o DPF:Click here
Electronically controlled brake system Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Control of vehicle speed by the dynamic radar cruise control system is canceled (in vehicle-to-vehicle distance control mode) Fail-safe chart Click here
Forward recognition camera is temporarily unavailable Click here
Millimeter wave radar sensor assembly is dirty Click here
Millimeter wave radar sensor assembly beam axis not adjusted
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.


Triangle Target:Click here
Flat Surface Target:Click here
Driving Adjustment:Click here
CAN communication system Click here
Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
Control of vehicle speed by the dynamic radar cruise control system is canceled (in vehicle-to-vehicle distance control mode) SFI system (for 1GR-FE) Click here
SFI system (for V35A-FTS) Click here
ECD system (for F33A-FTV) w/ DPF:Click here
w/o DPF:Click here
Electric parking brake system Click here
Electronically controlled brake system Click here
Millimeter wave radar sensor assembly Click here
Forward recognition camera Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Hunting/vehicle speed is not constant (in constant speed control mode) CAN communication system Click here
Electronically controlled brake system Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Hunting/vehicle speed is not constant (in vehicle-to-vehicle distance control mode) Millimeter wave radar sensor assembly is dirty Click here
Millimeter wave radar sensor assembly beam axis not adjusted
HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.


Triangle Target:Click here
Flat Surface Target:Click here
Driving Adjustment:Click here
CAN communication system Click here
Electronically controlled brake system Click here
Millimeter wave radar sensor assembly Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Vehicle speed control by the dynamic radar cruise control system is not canceled when the CANCEL switch is pushed Meter/gauge system Click here
Steering pad switch assembly Click here
Spiral cable sub-assembly Click here
Multiplex network steering ECU Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Depressing the brake pedal does not cancel control of vehicle speed by the dynamic radar cruise control system Stop light switch circuit Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Control cannot be canceled while the vehicle is stopped CAN communication system Click here
Electronically controlled brake system Click here
Electric parking brake system Click here
Seat belt warning system Click here
Door courtesy switch circuit Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Control cannot be canceled by operating the parking brake Electric parking brake system Click here
CAN communication system Click here
No. 2 skid control ECU (brake actuator assembly) (for RHD) Click here
No. 2 skid control ECU (brake actuator assembly) (for LHD) Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Even though the millimeter wave radar sensor assembly and forward recognition camera are not dirty, the warning message "Radar Cruise Control Unavailable See Owner's Manual" is displayed Millimeter wave radar sensor assembly Click here
Forward recognition camera Click here
The vehicle approach warning buzzer does not sound Meter/gauge system Click here
Check millimeter wave radar sensor assembly installation position Click here
Check installation of forward recognition camera Click here
Forward recognition camera Click here
Millimeter wave radar sensor assembly Click here
Even though the vehicle approach warning buzzer is sounding, brake control is not performed to decelerate the vehicle Electronically controlled brake system Click here
CAN communication system Click here
Forward recognition camera Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Even though the SET function is operating, the cruise SET indicator does not illuminate CAN communication system Click here
Cruise SET indicator light circuit Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
The cruise control indicator remains illuminated CAN communication system Click here
Cruise main indicator light circuit Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
Indicators are not displayed on the multi-information display in the combination meter assembly CAN communication system Click here
Combination meter assembly Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
A buzzer does not sound when control of vehicle speed by the dynamic radar cruise control is canceled CAN communication system Click here
Combination meter assembly Click here
ECM (for 1GR-FE) Click here
ECM (for V35A-FTS) Click here
ECM (for F33A-FTV) Click here
The dynamic radar cruise control system operates normally but the curve speed reduction function does not operate Customize parameters Click here
Front camera system Click here
Forward recognition camera Click here