Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CAMSHAFT (w/o DPF) › 2014.08–2017.01
RM25T0E _51 Engine / Hybrid System _029207 1VD-FTV ENGINE MECHANICAL _0132951 CAMSHAFT(w/o DPF) A

1VD-FTV ENGINE MECHANICAL  CAMSHAFT(w/o DPF)  INSTALLATION  


PROCEDURE

Hide 13511 1.INSTALL NO. 1 AND NO. 2 CAMSHAFTS

NOTICE:
A168355C01
0.583,0.417 0.75,0.417 0.75,0.417 1.479,0.677 true 2.833,1.75 2.833,1.583 2.833,1.583 2.229,1.021 true 0.438,0.313 0.75,0.469 0.313,0.156 10 false *a 2.771,1.76 3.083,1.917 0.313,0.156 10 false *b 1.5,1.344 1.813,1.5 0.313,0.156 10 false *c
*a Dot Mark
*b Matchmark
*c Number of Gear Teeth


If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.


a.
A329702

Add more than 19 cc (1.2 cu.in.) of engine oil into the cylinder head sub-assembly RH side oil holes.


b.
A164816

Apply engine oil to the No. 1 valve rocker arm sub-assembly rollers and camshaft housing of the cylinder head sub-assembly RH.


c.

Install the No. 1 and No. 2 camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.
A168400C01
1.719,1.292 2.25,0.25 2.25,0.25 1.854,1.302 true 2.25,0.25 2.5,0.25 false 2.521,0.167 2.833,0.323 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the No. 1 and No. 2 camshaft timing gears shown in the illustration.


iii.

Place the 2 camshafts into the cylinder head sub-assembly RH.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the No. 1 valve rocker arm sub-assemblies to the No. 1 valve lash adjuster assemblies.




d.

Install the No. 1 camshaft bearing cap.

i.

Align the No. 1 camshaft bearing cap and the ring pins of the No. 2 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



e.

Install the No. 3 camshaft bearing caps.

i.
A168376

Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the camshaft oil feed pipe sub-assembly, by hand.



f.

Temporarily install the No. 1 and No. 2 camshaft oil feed pipe sub-assemblies with the 8 bolts by hand.

NOTICE:

If even one of the camshaft oil feed pipe sub-assembly bolt holes does not match its No. 3 camshaft bearing cap bolt hole, replace the camshaft oil feed pipe sub-assembly.


HINT:

The camshaft oil feed pipe sub-assembly is bent on the intake side, and straight on the exhaust side.



g.

Temporarily install the 2 union bolts.


h.
A329738C01
0.365,0.375 0.552,0.563 0.188,0.188 10 true 20 0.281,0.813 0.469,1.031 0.188,0.219 10 true 19 0.406,1.792 0.594,2.01 0.188,0.219 10 true 18 0.313,1.323 0.49,1.51 0.177,0.188 10 true 17 3.073,0.646 3.26,0.833 0.188,0.188 10 true 16 3.042,0.896 3.25,1.073 0.208,0.177 10 true 15 3.031,1.469 3.24,1.635 0.208,0.167 10 true 14 3.052,1.24 3.26,1.427 0.208,0.188 10 true 13 0.917,0.354 1.125,0.51 0.208,0.156 10 true 12 1.281,0.906 1.49,1.083 0.208,0.177 10 true 11 0.958,1.823 1.271,2.021 0.313,0.198 10 false 10 1.313,1.25 1.469,1.438 0.156,0.188 10 true 9 2.167,0.333 2.313,0.5 0.146,0.167 10 false 8 2.469,0.896 2.625,1.083 0.156,0.188 10 true 7 2.167,1.813 2.479,2.01 0.313,0.198 10 false 6 2.469,1.25 2.635,1.417 0.167,0.167 10 true 5 1.552,0.344 1.708,0.51 0.156,0.167 10 false 4 1.885,0.906 2.031,1.083 0.146,0.177 10 true 3 1.583,1.823 1.896,2.021 0.313,0.198 10 false 2 1.885,1.24 2.031,1.417 0.146,0.177 10 true 1
V100135

12 mm Head Bolt
V100136

10 mm Head Bolt


Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


j.
A164905

Remove the service bolt from the No. 1 camshaft timing gear.

NOTICE:

Do not drop the service bolt into the timing chain cover sub-assembly.


HINT:

If the service bolt is difficult to remove, rotate the camshaft and remove the service bolt. Then realign the matchmarks of the No. 1 and No. 2 camshaft timing gears.



k.

Temporarily install the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket to the No. 2 camshaft.


l.

Temporarily install the pump drive shaft gear with the 2 bolts.


m.
A168362N01
0.667,1.083 0.667,0.375 true 0.531,1.094 0.99,1.292 0.458,0.198 10 false SST

Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


n.

Rotate the crankshaft clockwise so that the 2 remaining pump drive shaft gear bolts can be installed.


o.

Temporarily install the 2 bolts to the pump drive shaft gear.


p.
A168362N01
0.667,1.083 0.667,0.375 true 0.531,1.094 0.99,1.292 0.458,0.198 10 false SST

Using SST, hold the pump drive shaft gear. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


q.
A168311

Remove the hexagon wrench from the No. 1 chain tensioner assembly.


r.

Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing chain cover sub-assembly.


s.

Apply adhesive to 3 or more threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



t.

Using a 10 mm hexagon wrench, install the taper screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 13053 2.INSTALL NO. 3 AND NO. 4 CAMSHAFTS

NOTICE:
A168355C01
0.583,0.417 0.75,0.417 0.75,0.417 1.479,0.677 true 2.833,1.75 2.833,1.583 2.833,1.583 2.229,1.021 true 0.438,0.313 0.75,0.469 0.313,0.156 10 false *a 2.771,1.76 3.083,1.917 0.313,0.156 10 false *b 1.5,1.344 1.813,1.5 0.313,0.156 10 false *c
*a Dot Mark
*b Matchmark
*c Number of Gear Teeth


If replacing a camshaft with a new one, make a matchmark on the new camshaft in the same place as the old camshaft. Determine the matchmark placement by using the dot mark as a reference point and counting the number of gear teeth from the dot mark to the matchmark as shown in the illustration.


a.
A329702

Add more than 19 cc (1.2 cu.in.) of engine oil into the cylinder head sub-assembly LH side oil holes.


b.
A164816

Apply engine oil to the No. 2 valve rocker arm sub-assembly rollers and camshaft housing of the cylinder head sub-assembly LH.


c.

Install the No. 3 and No. 4 camshafts.

i.

Apply engine oil to the camshaft journals, lobes, thrust portion and gears.


ii.
A168401C01
1.604,1.354 1.083,0.167 1.083,0.167 1.729,1.354 true 0.917,0.167 1.083,0.167 false 0.771,0.073 1.083,0.229 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the No. 3 and No. 4 camshaft timing gears shown in the illustration.


iii.

Place the 2 camshafts into the cylinder head sub-assembly LH.

NOTICE:
A164641

Before and after setting the camshafts, firmly set the No. 2 valve rocker arm sub-assemblies to the No. 2 valve lash adjuster assemblies.




d.

Install the No. 4 camshaft bearing cap.

i.

Align the No. 4 camshaft bearing cap and the ring pins of the No. 5 camshaft bearing cap.


ii.

Temporarily install the 4 bolts by hand.



e.

Install the No. 3 camshaft bearing caps.

i.
A168380

Confirm the marks and numbers on the No. 3 camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 8 bolts, which are not installed with the camshaft oil feed pipe sub-assembly, by hand.



f.

Temporarily install the No. 3 and No. 4 camshaft oil feed pipe sub-assemblies with the 8 bolts by hand.

NOTICE:

If even one of the camshaft oil feed pipe sub-assembly bolt holes does not match its No. 3 camshaft bearing cap bolt hole, replace the camshaft oil feed pipe sub-assembly.


HINT:

The camshaft oil feed pipe sub-assembly is bent on the intake side, and straight on the exhaust side.



g.

Temporarily install the 2 union bolts.


h.
A329739N01
0.25,0.323 0.438,0.5 0.188,0.177 10 true 20 0.208,0.802 0.396,1 0.188,0.198 10 true 19 0.302,1.76 0.49,1.958 0.188,0.198 10 true 18 0.24,1.281 0.427,1.479 0.188,0.198 10 true 17 3.188,0.615 3.385,0.844 0.198,0.229 10 true 16 3.188,0.854 3.375,1.042 0.188,0.188 10 true 15 3.167,1.448 3.417,1.635 0.25,0.188 10 true 14 3.167,1.208 3.375,1.375 0.208,0.167 10 true 13 1.031,0.281 1.25,0.458 0.219,0.177 10 true 12 1.375,0.854 1.583,1.021 0.208,0.167 10 true 11 1.073,1.781 1.385,1.979 0.313,0.198 10 false 10 1.438,1.219 1.583,1.396 0.146,0.177 10 true 9 2.292,0.281 2.427,0.448 0.135,0.167 10 true 8 2.594,0.865 2.74,1.042 0.146,0.177 10 true 7 2.281,1.781 2.594,1.979 0.313,0.198 10 false 6 2.594,1.219 2.75,1.385 0.156,0.167 10 true 5 1.677,0.292 1.823,0.458 0.146,0.167 10 true 4 2,0.865 2.135,1.042 0.135,0.177 10 true 3 1.708,1.781 2.021,1.979 0.313,0.198 10 false 2 2,1.219 2.135,1.406 0.135,0.188 10 true 1

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


i.

Tighten the 2 union bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


j.
A164905

Remove the service bolt from the No. 4 camshaft timing gear.

NOTICE:

Do not drop the service bolt into the timing chain cover sub-assembly.


HINT:

If the service bolt is difficult to remove, rotate the camshaft and remove the service bolt. Then realign the matchmarks of the No. 3 and No. 4 camshaft timing gears.



k.

Temporarily install the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket to the No. 3 camshaft with the 2 bolts.


l.
A168364N01
2.031,0.667 2.833,0.667 true 2.875,0.583 3.333,0.781 0.458,0.198 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


m.

Rotate the crankshaft pulley clockwise so that the 2 remaining No. 2 camshaft timing sprocket bolts can be installed.


n.

Temporarily install the 2 bolts to the No. 3 camshaft.


o.
A168364N01
2.031,0.667 2.833,0.667 true 2.875,0.583 3.333,0.781 0.458,0.198 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket. Tighten the 2 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


p.
A168321

Remove the hexagon wrench from the No. 2 chain tensioner assembly.


q.

Remove the adhesive from the threads of the taper screw plug and the bolt hole of the timing chain cover sub-assembly.


r.

Apply adhesive to 3 or more threads of the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



s.

Using a 10 mm hexagon wrench, install the taper screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


Hide 3.CHECK NO. 1 CYLINDER AT TDC/COMPRESSION

a.

Rotate the crankshaft clockwise 3 times or more, and check that the timing marks of the camshafts (1 dot mark each) align. If the timing marks of the camshafts do not align, repeat the "Install No. 3 and No. 4 Camshafts" and "Install No. 1 and No. 2 Camshafts" procedures.

A326382


Hide 23670 4.INSTALL INJECTOR ASSEMBLY (for Bank 1)

Hide 23670 5.INSTALL INJECTOR ASSEMBLY (for Bank 2)

Hide 11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23681D 7.INSTALL NOZZLE HOLDER SEAL RH

Hide 11202 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 23681E 9.INSTALL NOZZLE HOLDER SEAL LH

Hide 12270 10.INSTALL OIL SEPARATOR ASSEMBLY

Hide 12263 11.CONNECT NO. 3 VENTILATION HOSE

Hide 23801L 12.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23805B 13.INSTALL NO. 5 FUEL PIPE SUB-ASSEMBLY

Hide 23820A 14.INSTALL COMMON RAIL ASSEMBLY LH

Hide 23706 16.INSTALL NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 23702 17.INSTALL INJECTION PIPE SUB-ASSEMBLY RH

Hide 23701 18.INSTALL INJECTION PIPE SUB-ASSEMBLY LH

Hide 12142 19.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 15301 20.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 44761 22.INSTALL VACUUM PUMP TO CONNECTOR TUBE

Hide 23804D 24.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY

Hide 26100G 26.INSTALL DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

Hide 82111 27.CONNECT ENGINE ROOM MAIN WIRE

a.

Connect the 17 connectors.


b.

Attach the 6 engine room main wire clamps.


c.

Install the 17 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25850 30.INSTALL ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 44769 31.INSTALL VACUUM RESERVOIR CONNECT TUBE

Hide 16264D 32.CONNECT NO. 2 AND NO. 3 WATER BY-PASS HOSES

Hide 17940D 36.INSTALL INTERCOOLER ASSEMBLY

Hide 87249B 38.CONNECT HEATER WATER OUTLET PIPE B

Hide 29300 40.INSTALL VACUUM PUMP ASSEMBLY

Hide 44774 41.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 17878 42.INSTALL NO. 3 INTAKE AIR CONNECTOR PIPE

Hide 74403A 44.INSTALL BATTERY CARRIER SUB-ASSEMBLY

Hide 23271H 46.CONNECT NO. 1 AND NO. 2 FUEL HOSES

Hide 44778 48.CONNECT CONNECTOR TO CHECK VALVE HOSE

Hide 16400 49.INSTALL RADIATOR ASSEMBLY

Hide 51.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 57.WARM UP ENGINE

NOTICE:

In order to bleed air from the chain tensioner assembly, drive the vehicle with the engine at 3000 rpm for 60 seconds or more.