Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2016.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM J

1VD-FTV ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing a fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


PROCEDURE

1.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 61

d.

Read DTCs.

Result:
Result Proceed to
No DTC is output A
DTCs related to engine B




A

2.CHECK FUEL FILTER ELEMENT ASSEMBLY

B

REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT

2.CHECK FUEL FILTER ELEMENT ASSEMBLY
a.

Check that the fuel filter element assembly is not clogged.

OK:

Fuel filter is not clogged.



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE CRANKING CONDITION

NG

REPLACE FUEL FILTER ASSEMBLY

3.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.


b.

Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.

OK:

Engine cranking condition is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FUEL PRESS)

NG

CHECK AND REPLACE BATTERY, CHARGING SYSTEM, STARTER ASSEMBLY AND STARTING SYSTEM

4.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

d.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Fuel Press Engine cranking, and engine coolant temperature 0°C (32°F) or more 20000 to 35000 kPa



Result:
Proceed to
OK
NG



OK

5.CHECK IF INITIAL COMBUSTION OCCURS

NG

5.CHECK IF INITIAL COMBUSTION OCCURS
a.

Check if initial combustion occurs.

Result:
Result Proceed to
No initial combustion with cold engine A
No initial combustion with hot engine B
Initial combustion occurs C




A

6.CHECK GLOW INDICATOR LIGHTING TIME AND AFTER-GLOW TIME

B

8.READ VALUE USING GTS (FUEL PRESS)

C

9.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
6.CHECK GLOW INDICATOR LIGHTING TIME AND AFTER-GLOW TIME
a.

Check the lighting duration of the glow indicator light.

OK:

Indicator lighting time is normal.



Result:
Proceed to
OK
NG



OK

7.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

7.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)
a.
A163041C01
1.354,2.927 1.677,3.083 false 1.677,2.896 1.719,2.896 false 1.781,3.052 2.135,3.229 0.354,0.177 10 true *1
*1 Screw Grommet


Disconnect the glow plug connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Glow plug terminal - Body ground 20°C (68°F) Approximately 1 Ω


HINT:

If any of the glow plugs has an open circuit, the engine power will be insufficient only when the engine is cold.


NOTICE:
·

Exercise extreme care not to damage the glow plug pipes. Damaging them could cause an open circuit, or shorten the life of the glow plugs.

·

Keep the glow plugs free of oil and fuel while cleaning.

·

Wipe any oil off of the terminal and Bakelite washer with a clean, dry cloth during inspection.

·

Do not apply more than 11 V to the glow plugs as it may cause an open circuit.




c.

Reconnect the glow plug connector.


Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FUEL PRESS)

NG

8.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

d.

Read the value.

OK:

The internal fuel pressure of the common rail is within the specification below.


Reference:
Engine Speed Fuel Pressure
Idling Approximately 27000 to 37000 kPa
2500 rpm (No engine load) Approximately 50000 to 70000 kPa



Result:
Proceed to
OK
NG



OK

9.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM

NG

14.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
9.CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
a.

Check the air intake system and exhaust system.

Click hereEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)

NG

REPAIR OR REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST

10.READ VALUE USING GTS (FUEL PRESS AND INJECTION VOLUME)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Injection Volume
Fuel Press
50003 61 376,54

d.

Enter the following menus in order and read the values.

·

Fuel Press

·

Injection Volume


Standard value:
Item Engine Speed* Reference Value
Fuel Press Idling 27000 to 37000 kPa
Fuel Press 2000 rpm (No engine load) 50000 to 70000 kPa
Fuel Press 3000 rpm (No engine load) 52000 to 76000 kPa
Injection Volume Idling 3.0 to 10.0 mm3
Injection Volume 2000 rpm (No engine load) 5.5 to 12.5 mm3
Injection Volume 3000 rpm (No engine load) 5.5 to 12.5 mm3


HINT:

*: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



Result:
Proceed to
OK
NG



OK

11.CHECK CYLINDER COMPRESSION PRESSURE

NG

15.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
11.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

12.HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

12.HARNESS AND CONNECTOR (FUEL INJECTOR - EDU)
a.
A311469C04
0.698,0.469 1.083,0.75 0.385,0.281 1.198,0.469 1.583,0.75 0.385,0.281 1.698,0.469 2.083,0.75 0.385,0.281 2.167,0.469 2.552,0.75 0.385,0.281 1.5,2.635 1.885,2.917 0.385,0.281 0.469,4.167 0.99,3.625 true 0.854,4.156 1.198,3.635 true 1.198,4.167 1.385,3.646 true 1.583,4.146 1.583,3.656 true 2.031,4.156 1.781,3.656 true 2.51,4.167 1.99,3.667 true 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 0.219,2.271 0.531,2.427 0.313,0.156 10 false *b 0.781,0.531 1.094,0.688 0.313,0.156 10 false C48 1.271,0.531 1.583,0.688 0.313,0.156 10 false C72 1.771,0.531 2.083,0.688 0.313,0.156 10 false C64 2.25,0.531 2.563,0.688 0.313,0.156 10 false C57 1.583,2.698 1.896,2.854 0.313,0.156 10 false C55 0.323,4.188 0.698,4.344 0.375,0.156 10 false INJ7 0.729,4.188 1.104,4.344 0.375,0.156 10 false INJ6 1.083,4.188 1.458,4.344 0.375,0.156 10 false INJ4 1.458,4.188 1.833,4.344 0.375,0.156 10 false INJ1 1.844,4.188 2.281,4.344 0.438,0.156 10 false COM1 2.365,4.188 2.813,4.365 0.448,0.177 10 false COM2
*a Front view of wire harness connector
(to Fuel Injector)
*b Front view of wire harness connector
(to No. 1 EDU)


Disconnect the C48, C72, C64 and C57 fuel injector connectors.


b.

Disconnect the C55 No. 1 EDU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (No. 1):
Tester Connection Condition Specified Condition
C48-2 - C55-4 (INJ1) Always Below 1 Ω
C72-2 - C55-3 (INJ4) Always Below 1 Ω
C64-2 - C55-2 (INJ6) Always Below 1 Ω
C57-2 - C55-1 (INJ7) Always Below 1 Ω
C48-1 - C55-5 (COM1) Always Below 1 Ω
C72-1 - C55-5 (COM1) Always Below 1 Ω
C64-1 - C55-6 (COM2) Always Below 1 Ω
C57-1 - C55-6 (COM2) Always Below 1 Ω
C48-2 or C55-4 (INJ1) - Body ground Always 10 kΩ or higher
C72-2 or C55-3 (INJ4) - Body ground Always 10 kΩ or higher
C64-2 or C55-2 (INJ6) - Body ground Always 10 kΩ or higher
C57-2 or C55-1 (INJ7) - Body ground Always 10 kΩ or higher
C48-1 or C55-5 (COM1) - Body ground Always 10 kΩ or higher
C72-1 or C55-5 (COM1) - Body ground Always 10 kΩ or higher
C64-1 or C55-6 (COM2) - Body ground Always 10 kΩ or higher
C57-1 or C55-6 (COM2) - Body ground Always 10 kΩ or higher



d.
A311469C05
0.667,0.333 1.083,0.594 0.417,0.26 1.188,0.333 1.604,0.594 0.417,0.26 1.708,0.333 2.125,0.594 0.417,0.26 2.25,0.333 2.667,0.594 0.417,0.26 1.448,2.656 1.865,2.917 0.417,0.26 1.833,4.167 1.583,3.646 true 2.75,4.083 2,3.667 true 2.271,4.156 1.781,3.646 true 1.333,4.167 1.417,3.646 true 0.896,4.167 1.219,3.646 true 0.417,4 1.052,3.646 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.208,2.688 0.521,2.885 0.313,0.198 10 false *b 1.563,2.708 2.021,2.906 0.458,0.198 10 false C53 0.76,0.385 1.052,0.563 0.292,0.177 10 false C67 1.292,0.385 1.583,0.552 0.292,0.167 10 false C51 1.792,0.385 2.094,0.563 0.302,0.177 10 false C49 2.333,0.385 2.635,0.573 0.302,0.188 10 false C63 0.302,4 0.917,4.198 0.615,0.198 10 false INJ3 0.75,4.219 1.365,4.417 0.615,0.198 10 false INJ8 1.229,4.229 1.844,4.427 0.615,0.198 10 false INJ5 1.75,4.24 2.365,4.438 0.615,0.198 10 false INJ2 2.167,4.24 2.781,4.438 0.615,0.198 10 false COM4 2.667,4.083 3.281,4.281 0.615,0.198 10 false COM5
*a Front view of wire harness connector
(to Fuel Injector)
*b Front view of wire harness connector
(to No. 2 EDU)


Disconnect the C67, C51, C49 and C63 fuel injector connectors.


e.

Disconnect the C53 No. 2 EDU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance (No. 2):
Tester Connection Condition Specified Condition
C67-2 - C53-4 (INJ2) Always Below 1 Ω
C51-2 - C53-3 (INJ5) Always Below 1 Ω
C49-2 - C53-1 (INJ3) Always Below 1 Ω
C63-2 - C53-2 (INJ8) Always Below 1 Ω
C67-1 - C53-5 (COM4) Always Below 1 Ω
C51-1 - C53-5 (COM4) Always Below 1 Ω
C49-1 - C53-6 (COM5) Always Below 1 Ω
C63-1 - C53-6 (COM5) Always Below 1 Ω
C67-2 or C53-4 (INJ2) - Body ground Always 10 kΩ or higher
C51-2 or C53-3 (INJ5) - Body ground Always 10 kΩ or higher
C49-2 or C53-1 (INJ3) - Body ground Always 10 kΩ or higher
C63-2 or C53-2 (INJ8) - Body ground Always 10 kΩ or higher
C67-1 or C53-5 (COM4) - Body ground Always 10 kΩ or higher
C51-1 or C53-5 (COM4) - Body ground Always 10 kΩ or higher
C49-1 or C53-6 (COM5) - Body ground Always 10 kΩ or higher
C63-1 or C53-6 (COM5) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.PERFORM GTS (CONTROL THE CYLINDER #1 TO #8 FUEL CUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM GTS (CONTROL THE CYLINDER #1 TO #8 FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the engine idle speed while the fuel injection to each cylinder is cut using the tester.

Result:
Result Proceed to
Becomes unstable A
Does not change B


HINT:

Replace the injector mounted on the cylinder that causes no significant idle speed change.




A

REPLACE INJECTOR DRIVER (NO. 1 OR NO. 2)

B

GO TO DTC P1238 INSPECTION PROCEDURE

14.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP
a.

Disconnect the inlet hose from the fuel supply pump.


b.

Operate the priming pump and check that fuel is being supplied to the fuel supply pump.

OK:

Fuel is properly supplied to the fuel supply pump when the priming pump is operated.



c.

Reconnect the inlet hose.


Result:
Proceed to
OK
NG



OK

NG

CHECK AND REPLACE FUEL PIPE CLOGGING (INCLUDING FUEL FREEZING) (FUEL TANK - FUEL SUPPLY PUMP)

15.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Coolant Temp Idling with warm engine (A/C switch OFF) 75 to 90°C (167 to 194°F)



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (ENGINE SPEED)

NG

19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
16.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 61 315

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Engine Speed Idling with warm engine (A/C switch OFF) 500 to 600 rpm



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST FUSE - ECM)

NG

20.INSPECT CRANKSHAFT POSITION SENSOR
17.CHECK HARNESS AND CONNECTOR (ST FUSE - ECM)
a.

Remove the ST fuse from the cowl side relay block assembly.


b.

Disconnect the A29 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
ST fuse terminal 2 - A29-48 (STA) Always Below 1 Ω
ST fuse terminal 2 or A29-48 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.READ VALUE USING GTS (FUEL PRESS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS ON.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.

Powertrain > Engine and ECT > Data List
Tester Display
Fuel Press
50003 61 54

e.

Read the value.

Standard value:
Item Inspection Condition Reference Value
Fuel Press Idling 27000 to 37000 kPa



Result:
Proceed to
OK
NG



OK

NG

21.INSPECT FUEL PRESSURE SENSOR
19.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Remove the engine coolant temperature sensor.

A163511C03
5.583,1.781 5.875,1.417 false 2.104,1.25 2.49,0.875 true 1.781,1.24 1.406,0.854 true 3.406,0.635 4.615,0.917 1.208,0.281 10 false Resistance kΩ 6.01,1.219 7.021,1.448 1.01,0.229 10 false Acceptable 4.646,0.708 4.969,0.917 0.323,0.208 8 false 30 4.646,0.833 4.969,1.042 0.323,0.208 8 false 20 4.646,1.042 4.969,1.25 0.323,0.208 8 false 10 4.646,1.302 4.969,1.51 0.323,0.208 8 false 5 4.646,1.458 4.969,1.667 0.323,0.208 8 false 3 4.646,1.625 4.969,1.833 0.323,0.208 8 false 2 4.646,1.823 4.969,2.031 0.323,0.208 8 false 1 4.646,2.354 4.969,2.563 0.323,0.208 8 false 0.2 4.646,2.229 4.969,2.438 0.323,0.208 8 false 0.3 4.646,2.073 4.969,2.281 0.323,0.208 8 false 0.5 4.646,2.583 4.969,2.792 0.323,0.208 8 false 0.1 5.115,2.917 5.344,3.302 0.229,0.385 8 false 0 (32) 5.365,2.917 5.677,3.24 0.313,0.323 8 false 20 (68) 5.604,2.917 5.938,3.24 0.333,0.323 8 false 40 (104) 5.875,2.917 6.219,3.24 0.344,0.323 8 false 60 (140) 6.135,2.917 6.563,3.24 0.427,0.323 8 false 80 (176) 6.427,2.917 6.792,3.24 0.365,0.323 8 false 100 (212) 4.865,2.917 5.104,3.25 0.24,0.333 8 false -20 (-4) 3.25,2.854 4.729,3.083 1.479,0.229 10 false Temperature °C (°F) 0.51,0.271 1.281,0.656 0.771,0.385 10 false *a 2.542,0.75 2.792,0.938 0.25,0.188 10 false E2 1.042,0.76 1.396,0.948 0.354,0.188 10 false THW
*a Component without harness connected
(Engine Coolant Temperature Sensor)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 (E2) - 2 (THW) 20°C (68°F) 2.29 to 2.60 kΩ
1 (E2) - 2 (THW) 80°C (176°F) 0.301 to 0.327 kΩ


NOTICE:

When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.


HINT:

Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.



c.

Reconnect the engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

20.INSPECT CRANKSHAFT POSITION SENSOR
a.
A165740C02
1.458,2.104 1.156,1.74 true 1.979,2.135 2.292,1.74 true 0.188,0.448 0.729,0.896 0.542,0.448 10 false *a 2.375,1.615 2.729,1.802 0.354,0.188 10 false NE+ 0.76,1.615 1.031,1.802 0.271,0.188 10 false NE-
*a Component without harness connected
(Crankshaft Position Sensor)


Disconnect the C42 crankshaft position sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 (NE+) - 2 (NE-) Cold 1630 to 2740 Ω
1 (NE+) - 2 (NE-) Hot 2065 to 3225 Ω


HINT:

In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" mean sapproximately 50 to 100°C (122 to 212°F).



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

21.INSPECT FUEL PRESSURE SENSOR
a.
A165963C01
1.458,2.375 1.125,2.833 true 1.729,2.385 1.74,2.833 true 2.083,2.365 2.375,2.823 true 0.24,0.469 1.198,0.938 0.958,0.469 10 false *a 0.99,2.844 1.229,3.021 0.24,0.177 10 false VC 1.635,2.844 1.875,3.021 0.24,0.177 10 false PR 2.292,2.844 2.531,3.021 0.24,0.177 10 false E2
*a Component without harness connected
(Fuel Pressure Sensor)


Disconnect the C56 fuel pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
2 (PR) - 1 (E2) Always 16.4 kΩ or less
2 (PR) - 3 (VC) Always 3 kΩ or less



Result:
Proceed to
OK
NG



OK

22.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

NG

22.HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.
A311456C10
1.458,0.146 1.854,0.375 0.396,0.229 1.323,2.313 1.719,2.542 0.396,0.229 1.177,1.604 1.458,1.094 true 2.135,1.615 1.875,1.104 true 1.667,1.615 1.667,1.104 true 0.531,4.177 0.906,3.396 true 1.365,4.188 0.99,3.396 true 2.063,4.167 1.427,3.396 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.125,2.021 0.438,2.219 0.313,0.198 10 false *b 1.5,0.177 1.917,0.385 0.417,0.208 10 false C100 1.094,1.646 1.406,1.844 0.313,0.198 10 false E2 1.583,1.646 1.896,1.844 0.313,0.198 10 false PR 2.083,1.646 2.396,1.844 0.313,0.198 10 false VC 1.396,2.344 1.708,2.542 0.313,0.198 10 false C39 0.396,4.208 1.104,4.479 0.708,0.271 10 false 69 (PCR1) 1.25,4.208 1.906,4.542 0.656,0.333 10 false 70 (VCM) 2.01,4.208 2.594,4.427 0.583,0.219 10 false 75 (E2)
*a Front view of wire harness connector
(to Fuel Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


Disconnect the C100 fuel pressure sensor connector.


b.

Disconnect the C39 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
C100-2 (PR) - C39-69 (PCR1) Always Below 1 Ω
C100-3 (VC) - C39-70 (VCM) Always Below 1 Ω
C100-1 (E2) - C39-75 (E2) Always Below 1 Ω
C100-2 (PR) or C39-69 (PCR1) - Body ground Always 10 kΩ or higher
C100-3 (VC) or C39-70 (VCM) - Body ground Always 10 kΩ or higher
C100-1 (E2) or C39-75 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.REPLACE ECM
a.

Replace the ECM.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL

NOTICE:

After replacing the ECM, the new ECM needs registration (see page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (see page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



b.

Check if the engine starts smoothly or if the engine stalls.

OK:

The engine starts smoothly and does not stall.



Result:
Proceed to
OK
NG



OK

END

NG