Home › Drivetrain › H150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for 1VD-FTV) › from 2022.09
RM25T0E _52 Drivetrain _029902 H150F MANUAL TRANSMISSION / TRANSAXLE _0137561 MANUAL TRANSMISSION ASSEMBLY(for 1VD-FTV) A

H150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for 1VD-FTV)  INSTALLATION  


PROCEDURE

Hide 31236B 1.INSTALL RELEASE FORK SUPPORT

Hide 31237 2.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

Hide 31204 3.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C313767

Install the 4 wire harness clamp brackets with the 4 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 5.INSTALL TRANSFER ASSEMBLY

C161482

a.

Install the transfer assembly to the manual transmission with the 6 bolts.

Torque:
68.6 N*m (700 kgf*cm, 51 ft.*lbf)


Hide 6.INSTALL MANUAL TRANSMISSION WITH TRANSFER

C160844

a.

Install the manual transmission with transfer with the 10 bolts.

Torque:
71.6 N*m (730 kgf*cm, 53 ft.*lbf)


Hide 7.CONNECT WIRE HARNESS

a.

Connect the connectors and clamps, and then connect the wire harness to the manual transmission with transfer.


b.

Tilt up the manual transmission with transfer.


c.
C312650

Install the wire harness clamp and connect the wire harness to the manual transmission with transfer.


d.
C312643

Connect the ground cable with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 12371 8.INSTALL REAR ENGINE MOUNTING INSULATOR

C161536

a.

Install the rear engine mounting insulator to the manual transmission with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 51203 9.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C160838

a.

Install the No. 2 frame crossmember sub-assembly with the 2 nuts.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)


b.

Install the 8 bolts.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 12140 10.INSTALL OIL PAN COVER

C163585

a.

Install the oil pan cover with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11.INSTALL FRONT STABILIZER BRACKET LH

C161532

a.

Install the front stabilizer bracket LH with the 2 bolts.

Torque:
29.7 N*m (303 kgf*cm, 22 ft.*lbf)


Hide 12.INSTALL FRONT STABILIZER BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 31470 13.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

C160837

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 37110 15.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Hide 37140 16.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 51447C 17.INSTALL TRANSFER CASE PROTECTOR

C161524

a.

Install the transfer case protector to the crossmember with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 36308 19.CONNECT HIGH AND LOW SHIFT ROD SUB-ASSEMBLY

a.

Connect the high and low shift rod sub-assembly with the washer and nut.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 21.INSPECT AND ADJUST TRANSFER SHIFT LEVER ASSEMBLY

Hide 33530F 22.INSTALL TRANSMISSION SHIFT LEVER ASSEMBLY

C313779C02
0.594,1.615 0.885,1.615 0.885,1.615 1.125,1.094 true 0.313,1.542 0.656,1.76 0.344,0.219 11 false *a
*a Cloth or Equivalent
V100135

Down
V100136

Clockwise


a.

Cover the transmission shift lever cap with a cloth or equivalent.


b.

While pressing down on the transmission shift lever cap, turn it clockwise to install the transmission shift lever.


Hide 58286 23.INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT

Hide 36303 24.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 89441A 25.INSTALL DECELERATION SENSOR (w/ ABS)

Hide 89170 26.INSTALL AIRBAG SENSOR ASSEMBLY WITH AIRBAG SENSOR BRACKET (w/ Airbag System)

Hide 62111A 31.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67913 33.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 87240 34.INSTALL HEATER WATER VALVE ASSEMBLY

C162223

a.

Install the heater water valve assembly to the vehicle with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the 2 hoses to the heater water valve assembly and slide the 2 clamps to secure it.


c.
C162224

Connect the cable to the heater water valve assembly.


Hide 16470 37.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 17875 38.INSTALL INTAKE AIR CONNECTOR PIPE

Hide 17805 39.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 40.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17881 42.INSTALL NO. 1 AIR CLEANER HOSE

Hide 16571C 43.INSTALL NO. 1 RADIATOR HOSE

Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 51442 50.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART