Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2022.09
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136559 ENGINE ASSEMBLY A

1GR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53301 5.REMOVE HOOD SUB-ASSEMBLY

a.

Disconnect the washer hose.


b.

Remove the 4 bolts and hood sub-assembly.


Hide 16400 9.REMOVE RADIATOR ASSEMBLY

Hide 17705 10.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

Hide 17801 11.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


Hide 17700 12.REMOVE AIR CLEANER ASSEMBLY

a.
A326598

Remove the 2 bolts, nut and air cleaner assembly.


Hide 17129 13.REMOVE INTAKE AIR SURGE TANK

Hide 17410 14.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Model Code #J78, #J79 Series)

Hide 17410 15.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Model Code #J71, #J76 Series)

Hide 53737B 16.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 17.REMOVE FRONT FENDER APRON SEAL RH

Hide 17105 19.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17104 21.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 87245A 22.DISCONNECT INLET HEATER WATER HOSE

a.
A221940

Slide the hose clamp and disconnect the inlet heater water hose from the heater core.


Hide 87246A 23.DISCONNECT OUTLET HEATER WATER HOSE

a.
A221941

Slide the hose clamp and disconnect the outlet heater water hose from the hose and valve assembly.


Hide 82121 24.DISCONNECT ENGINE WIRE

a.

Disconnect the 5 connectors.

A328462C01
0.083,0.083 0.396,0.24 0.313,0.156 10 true *A 3.75,0.083 4.063,0.24 0.313,0.156 10 true *B
*A for LHD *B for RHD



b.

Detach the 2 wire harness clamps.


c.
A221949

Detach the 2 claws and remove the fuse block cover.


d.
A221935

Remove the bolt and disconnect the No. 2 engine wire from the fuse block.


e.
A218597

Disconnect the connector and engine room main wire.


f.
A221944

Remove the 2 nuts, detach the 2 wire harness clamps and disconnect the No. 2 engine wire.


g.
A221939

Remove the bolt and disconnect the ground cable from the rear water by-pass joint.


h.
A218596

Remove the bolt and disconnect the No. 7 engine wire.


Hide 31482 25.DISCONNECT CLUTCH TUBE

Hide 88712 26.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Air Conditioning System)

Hide 44310 27.DISCONNECT VANE PUMP ASSEMBLY

a.
A221942

Disconnect the connector.


b.

Remove the 2 bolts and disconnect the vane pump assembly.

NOTICE:

Do not hit other parts with the pulley when disconnecting the vane pump assembly.


HINT:

Be sure to suspend the vane pump assembly securely.



Hide 12395 28.REMOVE ENGINE MOUNTING BRACKET HEAT INSULATOR

a.
A221947

Remove the 3 bolts and engine mounting bracket heat insulator.


Hide 27020 29.REMOVE GENERATOR ASSEMBLY

Hide 88320 30.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 16631B 31.REMOVE IDLER PULLEY BRACKET (w/o Air Conditioning System)

Hide 23801P 32.DISCONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY AND NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Remove the No. 1 fuel pipe clamp.


b.
A221937

Disconnect the No. 1 fuel pipe sub-assembly and No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 37110 33.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 37140 34.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 12371 36.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Only perform this procedure when replacement of the rear No. 1 engine mounting insulator is necessary.


Click hereDrivetrain>H150F (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSMISSION ASSEMBLY (for 1GR-FE)>REMOVAL

Hide 31210 37.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250 38.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 39.REMOVE FLYWHEEL SUB-ASSEMBLY

a.
A174383N01
2.438,0.427 1.365,0.427 true 1.76,0.427 1.76,0.781 true 1.365,0.427 1.365,0.698 true 2.49,0.354 2.854,0.583 0.365,0.229 10 true SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A326599

Remove the 8 bolts and flywheel sub-assembly.

NOTICE:

Do not reuse the bolts.



Hide 40.INSTALL ENGINE HANGER

a.
A174384C01
1.177,1.646 0.635,0.323 false 0.635,0.323 0.542,0.323 false 2.927,1.708 2.365,0.323 false 2.365,0.323 2.271,0.323 false 0.313,0.229 0.51,0.406 0.198,0.177 10 false *1 2.052,0.229 2.271,0.438 0.219,0.208 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 engine hanger 12281-31060
No. 2 engine hanger 12282-31040
Bolt 90119-08A87



Hide 41.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.
A221948

Remove the 2 nuts and 2 washers, and then lift the engine out of the vehicle carefully.

NOTICE:

Make sure the engine is clear of all wiring and hoses.



Hide 42.INSTALL ENGINE STAND

a.

Install the engine to an engine stand with bolts.


Hide 43.REMOVE ENGINE HANGER

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.


Hide 12361 44.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Only perform this procedure when replacement of the front engine mounting insulator is necessary.


a.

Remove the 2 nuts and 2 front engine mounting insulators.