Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2021.08
RM37H0E _51 Engine / Hybrid System _096346 HYBRID / BATTERY CONTROL _0463852 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1E1A13  FC Interlock Switch Circuit Open  P1E1A92  FC Interlock Switch Performance or Incorrect Operation  


DTC SUMMARY

MALFUNCTION DESCRIPTION


The EV control ECU detects that a FC safety device (FC interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)

The cause of this malfunction may be one of the following:

Detection switch system malfunction
·

FC converter power outlet cable malfunction

·

FC converter assembly malfunction


Low-voltage system malfunction
·

EV control ECU malfunction

·

FCDC converter control ECU malfunction

·

FC converter assembly malfunction

·

Wire harness malfunction

·

Connector malfunction



DESCRIPTION

When the EV control ECU detects that a FC safety device (FC interlock) is operated, such as when the FC converter outlet cable is removed, it will prohibit the system operation or shut off the system main relay.

The safety device is installed to the FC converter outlet cable connector of the FC converter assembly.

If the FCDC converter control ECU board sub-assembly, No. 1 FC converter wire is removed, the interlock signal line will be open.

If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. When the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned ON again.

When an open circuit is detected, the system main relays will be shut off when the next drive cycle starts, until the system returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate DTC Output from Priority
P1E1A13 FC Interlock Switch Circuit Open With the vehicle stopped, the FC interlock signal line became open.
(1 trip detection logic)
·

FCDC converter control ECU board sub-assembly

·

EV control ECU

·

FC converter power outlet terminal sub-assembly

·

FC converter power outlet cable (inverter with converter assembly)

·

No. 1 FC converter wire


Master Warning:
Comes on
EV A
P1E1A92 FC Interlock Switch Performance or Incorrect Operation FC interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more).
(1 trip detection logic)
·

FCDC converter control ECU board sub-assembly

·

EV control ECU

·

FC converter power outlet terminal sub-assembly

·

FC converter power outlet cable (inverter with converter assembly)

·

No. 1 FC converter wire


Master Warning:
Comes on
EV A

CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Turn the ignition switch to ON and wait for 5 seconds or more.

2.

Enter the following menus: Powertrain / EV / Utility / All Readiness.

3.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform driving pattern again.




WIRING DIAGRAM

A491120E01
5.938,3.125 7.052,3.344 1.115,0.219 10 false EV Control ECU 5.938,2.927 6.396,3.125 0.458,0.198 10 false A15 5.771,1.292 6.229,1.49 0.458,0.198 10 false 7 4.542,1.063 5,1.26 0.458,0.198 10 false ILKI 4.917,1.167 5.375,1.365 0.458,0.198 10 false B19 3.531,3.073 4.729,3.615 1.198,0.542 10 false FCDC Converter Control ECU Board Sub-Assembly 5.979,1.063 6.438,1.26 0.458,0.198 10 false SILK 0.833,1.802 2.531,2.167 1.698,0.365 10 false FC Converter Power Outlet Terminal Sub-assembly 3.615,1.073 4.073,1.271 0.458,0.198 10 false ILKCO 3.625,2.438 4.083,2.635 0.458,0.198 10 false ILKCI 3.323,0.948 3.781,1.146 0.458,0.198 10 false 1 3.302,2.344 3.76,2.542 0.458,0.198 10 false 11 1.688,3.875 4.063,4.188 2.375,0.313 10 false FC Converter Assembly 3.333,1.167 3.792,1.365 0.458,0.198 10 false A 3.333,2.573 3.792,2.771 0.458,0.198 10 false A 4.938,0.948 5.396,1.146 0.458,0.198 10 false 10 1.146,1.167 1.604,1.365 0.458,0.198 10 false B 1.156,0.958 1.615,1.156 0.458,0.198 10 false 1 1.146,2.563 1.604,2.76 0.458,0.198 10 false B 1.167,2.344 1.625,2.542 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the EV battery service plug grip and FC converter power outlet cable on FC converter side.

Make sure to remove the service plug grip first.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the EV supply battery assembly

-

Disconnecting the low voltage connector of the FC converter assembly

-

Disconnecting the low voltage connector of the voltage inverter (for 1500W Type Voltage Inverter)


·
A484004

To prevent electric shock, make sure to remove the EV battery service plug grip and FC converter power outlet cable on FC converter side to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, store them according to the following guidelines to prevent other technicians from accidentally reconnecting them while work is being performed on the high voltage systems.

-

The technician performing the work should put the EV battery service plug grip in their pocket and carry it with them.

-

Remove the FC converter power outlet cable on FC converter side with a "HIGH-VOLTAGE, DO NOT TOUCH" caution tag attached to it for other technicians.


·
A484005C01
1.667,0.74 2.115,0.427 true 2.188,0.385 2.448,0.552 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the EV battery service plug grip and FC converter power outlet cable on FC converter side, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly and the FC converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the EV supply battery assembly with insulating tape after removing it.

If the EV supply battery assembly stored without insulating the connectors and terminals, electric shock or fire may result.

·
A484932

Since high voltage accumulates within the FC stack assembly with FC converter, never perform the work of separating the FC stack assembly with FC converter into the FC converter assembly and FC stack assembly without first performing electrical charge discharge (forced electrical charge discharge or electrical charge self-discharge), because doing so is dangerous.

Click hereEngine / Hybrid System>FC CONTROL>FC STACK>REMOVAL

·

Removing and installing the FC stack assembly without first discharging the electrical charge may result in an electric shock due to the high voltage circuit.



NOTICE:
·

After turning the ignition switch off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION


·

This vehicle performs FC system shutdown process after turning the ignition switch off from ON (READY). Therefore, after the ignition switch is turned off from ON (READY), do not perform any work on the electrical system for at least 10 minutes including removing connectors or disconnecting the negative (-) auxiliary battery terminal.

·

When the EV control ECU determines that the temperature of FC system components is below 0°C (32°F) when the vehicle is parked with the ignition switch off, it operates the FC air compressor, hydrogen pump and FC cooling water pump for a maximum of 180 seconds to drain the FC stack assembly. When performing inspection or repairs with the ignition switch off (not ON or ON (READY)), disconnect the cable from the negative (-) auxiliary battery terminal before performing work. (If the auxiliary battery voltage is needed to conduct inspection, perform the inspection in an environment with an ambient temperature of 10°C (50°F) or higher.)



PROCEDURE

1.CHECK DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
Only P1E1A13 or P1E1A92 is output A
P1E1A13 or P1E1A92 is output and any DTCs in the table below are output B


Malfunction Content Relevant DTC
Microcomputer malfunction P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060687 Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message
P060B49 Drive Motor "A" Control Module Internal Electronic Failure
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
Power source circuit malfunction P06881F ECM/PCM Power Relay Sense Circuit Intermittent
System malfunction P1C9E9F Hybrid/EV System Reset Stuck Off


Post-procedure1

a.

Turn the ignition switch off.



A

2.CLEAR DTC

B

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

2.CLEAR DTC

NEXT

3.RECONFIRM DTC OUTPUT (EV)
3.RECONFIRM DTC OUTPUT (EV)

Pre-procedure1

a.

None.


Procedure1

a.

Check for DTCs.

Powertrain > EV > Trouble Codes
50001 397
Result:
Result Proceed to
P1E1A13 or P1E1A92 is output A
P1E1A13 or P1E1A92 is not output B



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

B

12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
4.CHECK CONNECTOR CONNECTION CONDITION (FC CONVERTER ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>FC CONTROL>FC CONTROL SYSTEM>P1D0619

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (EV CONTROL ECU CONNECTOR)

OK

6.CHECK FC CONVERTER POWER OUTLET CABLE (INTERLOCK)

NG

CONNECT SECURELY

6.CHECK FC CONVERTER POWER OUTLET CABLE (INTERLOCK)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



Procedure1

a.
A492124C02
2.073,1.958 1.958,1.958 1.958,1.958 1.74,1.635 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *1 2.146,1.875 2.458,2.073 0.313,0.198 10 true *a
*1 FC Converter Power Outlet Cable (Inverter with Converter Assembly)
*a Interlock Connector


Check the condition of the FC converter power outlet cable interlock.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



Result:
Proceed to
OK
NG


Post-procedure1

a.

None.



OK

7.CHECK EV CONTROL ECU

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

7.CHECK EV CONTROL ECU
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip and FC converter power outlet cable are not installed.

NOTICE:

After removing the service plug grip and FC converter power outlet cable, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481478

Disconnect the B19 FC converter connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


Procedure1

a.
A365593C99
0.26,0.865 0.688,1.229 0.427,0.365 1.802,1.031 2.552,1.854 true 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.375,0.969 0.833,1.167 0.458,0.198 10 false B19 2.563,1.865 3.021,2.063 0.458,0.198 10 false ILKI
*a Front view of wire harness connector
(to FC Converter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(B19)Location & Routing

Click Connector(B19)Engine Compartment>No. 2 Stack Wire>FC Converter Assembly

B19-10 (ILKI) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.

Reconnect the B19 FC converter connector.


d.

Install the electric heater sub-assembly.



OK

8.REMOVE FC CONVERTER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (SILK TERMINAL VOLTAGE)
8.REMOVE FC CONVERTER ASSEMBLY
HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK NO. 1 FC CONVERTER WIRE
9.CHECK NO. 1 FC CONVERTER WIRE

Pre-procedure1

a.
A481480

Remove the No. 1 FC converter wire from the FCDC converter control ECU board sub-assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



b.
A491115

Remove the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



Procedure1

a.
A491114C02
1.479,0.073 1.906,0.438 0.427,0.365 1.521,1.958 1.948,2.323 0.427,0.365 2.406,1.927 1.885,1.458 true 1.135,1.938 1.531,1.438 true 2.969,3.458 2.479,2.865 true 2.25,3.51 2.448,3.021 true 2.865,3.521 3.333,3.719 0.469,0.198 10 false ILKCO 0.771,1.958 1.542,2.156 0.771,0.198 10 false ILKCO 2.385,1.958 2.875,2.135 0.49,0.177 10 false ILKCI 2.083,3.521 2.49,3.708 0.406,0.188 10 false ILKCI 1.646,0.219 1.865,0.469 0.219,0.25 10 false B 1.688,2.063 1.917,2.271 0.229,0.208 10 false A 0.177,0.156 0.948,0.354 0.771,0.198 10 false *a
*a Component without harness connected
(No. 1 FC Converter Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (ILKCO) - B-2 (ILKCO) Ignition switch off Below 1 Ω
A-11 (ILKCI) - B- 1 (ILKCI) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Reconnect the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.


b.

Reconnect the No. 1 FC converter wire from the FCDC converter control ECU board sub-assembly.



OK

10.CHECK FC CONVERTER POWER OUTLET TERMINAL SUB-ASSEMBLY

NG

REPLACE NO. 1 FC CONVERTER WIRE

10.CHECK FC CONVERTER POWER OUTLET TERMINAL SUB-ASSEMBLY

Pre-procedure1

a.
A491115

Remove the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



b.
A491116

Remove the FC converter power outlet terminal sub-assembly from the FC converter assembly.

HINT:

Click hereEngine / Hybrid System>FC CONTROL>CONVERTER ASSEMBLY>DISASSEMBLY



Procedure1

a.
A491113C02
1.5,0.125 1.906,0.469 0.406,0.344 0.177,3.198 0.594,3.552 0.417,0.354 1.375,2.042 1.667,1.094 true 1.688,4.125 2.042,3.406 true 2.188,2.01 1.813,1.104 true 2.74,4.104 2.333,3.396 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.667,0.208 1.927,0.406 0.26,0.198 10 false C 0.344,3.302 0.604,3.5 0.26,0.198 10 false B 1.135,2.063 1.573,2.281 0.438,0.219 10 false ILKCI 2.75,4.156 3.188,4.375 0.438,0.219 10 false ILKCO 2.198,2.063 2.635,2.281 0.438,0.219 10 false ILKCO 1.365,4.156 1.802,4.375 0.438,0.219 10 false ILKCI
*a Component without harness connected
(FC Converter Power Outlet Terminal Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (ILKCI) - C-2 (ILKCI) Ignition switch off Below 1 Ω
B-2 (ILKCO) - C-1 (ILKCO) Ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

Install the FC converter power outlet terminal sub-assembly from the FC converter assembly.


b.

Reconnect the No. 1 FC converter wire from the FC converter power outlet wire sub-assembly.



OK

REPLACE FCDC CONVERTER CONTROL ECU BOARD SUB-ASSEMBLY

NG

REPLACE FC CONVERTER POWER OUTLET TERMINAL SUB-ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (SILK TERMINAL VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Remove the electric heater sub-assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>HEATER ASSEMBLY>REMOVAL



c.
A481478

Disconnect the B19 FC converter connector.


Procedure1

a.
A478491C25
0.844,0.802 1.24,1.156 0.396,0.354 0.802,1.688 0.552,2.438 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 0.938,0.917 1.24,1.083 0.302,0.167 10 false A15 0.438,2.479 0.823,2.646 0.385,0.167 10 false SILK
*a Component with harness connected
(EV Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A15)Location & Routing

Click Connector(A15)Instrument Panel>Front Compartment Main Wire>EV Control ECU

A15-7 (SILK) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.


b.

Reconnect the B19 FC converter connector.


c.

Install the electric heater sub-assembly.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

12.CHECK CONNECTOR CONNECTION CONDITION (INTERLOCK CIRCUIT)
a.

Check the connections of each connector.

OK:

Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CONNECTOR