Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2011.12–2013.12
RM2170E _54 Brake _057021 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0278020 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1256/56  Accumulator Low Pressure  


DESCRIPTION

The accumulator pressure sensor is built into the brake actuator (brake booster with master cylinder assembly) and detects the accumulator pressure.

The skid control ECU turns on the brake warning light / red (malfunction) and brake warning light / yellow (minor malfunction), and sounds the meter buzzer if it senses a decrease in the accumulator pressure.

DTC C1256/56 may be stored if the accumulator pressure drops due to frequent braking (this is not a malfunction).

DTC No. INF Code DTC Detection Condition Trouble Area
C1256/56 341 Significant drop in accumulator pressure continues.
(DTCs will be stored and the buzzer will operate when either condition is met.)
·

Accumulator pressure dropped due to frequent brake pedal operation (not a malfunction)

·

Pump motor malfunction

·

Accumulator deterioration

·

Accumulator pressure sensor (Brake booster with master cylinder assembly)

·

Supply voltage reduced



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

When C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 are output together with C1256/56, inspect and repair the trouble areas indicated by C1202/68, C1241/41, C1252/52, C1253/53 and/or C1391/69 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1202/68, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1241/41, Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1252/52, or Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1391/69).


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Ask the customer if frequent braking was performed while the brake warning light / yellow (minor malfunction) was on.

OK:
Result Proceed to
Frequent braking was not performed. A
Frequent braking was performed. B


HINT:

This DTC may be stored even if the accumulator pressure drops only temporarily due to frequent braking.




A

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY

B

END

2.INSPECT BRAKE BOOSTER PUMP ASSEMBLY
a.
U162274E02
0.99,1.656 0.708,2.708 false 1.177,1.656 1.458,2.708 false 2.427,0.552 1.99,1.563 false 1.344,0.552 1.781,1.563 false 2.188,0.323 2.667,0.49 0.479,0.167 10 false GND2 0.479,2.729 0.896,2.896 0.417,0.167 10 false GND1 1.302,2.729 1.656,2.885 0.354,0.156 10 false BM1 1.229,0.323 1.604,0.479 0.375,0.156 10 false BM2 0.177,0.167 0.375,0.302 0.198,0.135 10 false *a 1.74,0.958 2.042,1.115 0.302,0.156 10 false A46 0.938,0.958 1.24,1.115 0.302,0.156 10 false A45

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the brake booster pump assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-1 (BM1) - A45-2 (GND1) Always Below 10 Ω
A46-2 (BM2) - A46-1 (GND2) Always Below 10 Ω
A45-1 (BM1) - A46-2 (BM2) Always Below 1 Ω
A45-2 (GND1) - A46-1 (GND2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Booster Pump Assembly)

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

3.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

C

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the brake booster pump assembly connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V
Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator


e.

Wait for 30 seconds without depressing the brake pedal.


f.

Check that the accumulator pressure sensor output value change is within the specified range.

OK:

Accumulator pressure sensor output value change is less than 0.55 V.




OK

NG

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SOLENOID VALVE)
a.

Select the Active Test on the intelligent tester (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Shift lever is in P.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System


b.

Perform the Active Test of the solenoid using the intelligent tester.



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

d.

Check that the output value of the wheel cylinder pressure sensor does not increase.

OK:

The output value of the wheel cylinder pressure sensor does not increase.


HINT:

If the output value increases, there may be brake fluid leaks in the brake actuator.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D




A

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

B

REPLACE BRAKE BOOSTER PUMP ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

D

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY