Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › from 2016.08
RM3210E _58 Vehicle Interior _047534 HEATING / AIR CONDITIONING _0230753 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

E339606C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Connect each connector.


c.

Install the 4 bolts (A).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Connect the parking brake pedal assembly with the bolt (B).

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Temporarily install the nut.


f.

Install the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


g.

Connect the drain cooler hose.


h.

for LHD:

i.

Engage each clamp.


ii.

Connect the relay block assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Connect each connector.



i.

for RHD:

i.

Engage each clamp.


ii.

Connect the relay block assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Connect the 3 earth wires with the 3 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Connect each connector.



Hide 55990B 3.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

a.

Engage the 6 claws to install the lower defroster nozzle assembly.


Hide 4.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 55308B 5.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

Install the No. 3 instrument panel to cowl brace sub-assembly with the bolt and nut.

Torque:
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

for LHD:

i.

Engage the clamp and 2 claws to connect the DLC3 connector.



Hide 55307C 6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.

Engage each clamp.


d.
E337333

Install the front floor mat to its original position as shown in the illustration.


Hide 55306A 7.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



c.

w/ PTC Heater:

i.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)



d.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.

Engage each clamp.


f.
E337323

Install the front floor mat to its original position as shown in the illustration.


Hide 8.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E342635C01
0.448,1.042 0.604,1.24 0.156,0.198 10 true 1 5.573,1.021 5.729,1.219 0.156,0.198 10 true 2 3.052,0.979 3.208,1.177 0.156,0.198 10 true 3 0.906,5.406 1.063,5.604 0.156,0.198 10 true 4 2.979,5.177 3.135,5.375 0.156,0.198 10 true 5 6.521,5.281 6.677,5.479 0.156,0.198 10 true 6
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut to install the air conditioner unit assembly.

E338056C02
4.115,1.021 4.271,1.219 0.156,0.198 10 true 1 0.667,4.729 0.823,4.927 0.156,0.198 10 true 2 5.823,1.021 5.979,1.219 0.156,0.198 10 true 3 4.688,5.417 4.844,5.615 0.156,0.198 10 true 4 5.771,4.74 5.927,4.938 0.156,0.198 10 true 5 3.271,5.354 3.427,5.552 0.156,0.198 10 true 6
V100135

Bolt
V100136

Screw
V100137

Nut - -


Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts, screws and nut in the order shown in the illustration.




Hide 55215D 9.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.

Engage the 2 clips to install the No. 3 dash panel insulator pad.


Hide 87212 10.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 4 claws to install the rear No. 1 air duct.


Hide 87212H 11.INSTALL REAR NO. 4 AIR DUCT

a.

Engage the 2 claws to install the rear No. 4 air duct.


Hide 87212J 12.INSTALL REAR NO. 5 AIR DUCT

a.
E343995C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear No. 5 air duct as shown in the illustration.


b.
E337320

Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the 2 guides.


d.

Install the 2 front floor carpet clips.


Hide 87212F 13.INSTALL REAR NO. 2 AIR DUCT

a.

Engage the 2 claws to install the rear No. 2 air duct.


Hide 87212G 14.INSTALL REAR NO. 3 AIR DUCT

a.
E343994C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the rear No. 3 air duct as shown in the illustration.


b.
E337313

Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the 2 guides.


d.

Install the 2 front floor carpet clips.


Hide 58569D 15.INSTALL FRONT FLOOR CAUTION PLATE COVER

a.
E341462C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw to install the front floor caution plate cover as shown in the illustration.


Hide 58817B 16.INSTALL FRONT NO. 2 CONSOLE BOX INSERT

a.
E340367C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.
E337301C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and clip to install the front No. 2 console box insert as shown in the illustration.


Hide 58816C 17.INSTALL FRONT NO. 1 CONSOLE BOX INSERT

a.
E340369C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide as shown in the illustration.


b.
E337306C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw and clip to install the front No. 1 console box insert as shown in the illustration.


Hide 88625Q 18.INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR

a.

Connect the aspirator and connector to install the cooler (room temp. sensor) thermistor.


Hide 33560 19.INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY

Hide 20.INSTALL TELEMATICS TRANSCEIVER WITH ANTENNA CORD (w/ Telematics Transceiver)

Hide 82878 21.INSTALL ECU INTEGRATION BOX LH (for RHD)

Hide 82877 22.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 85970A 23.INSTALL DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)

Hide 89340A 24.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)

Hide 89343D 25.INSTALL NO. 2 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)

Hide 89343C 26.INSTALL NO. 1 CLEARANCE WARNING BUZZER (w/ TOYOTA Parking Assist-sensor System)

Hide 85940 27.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 88150A 28.INSTALL DRIVING SUPPORT ECU ASSEMBLY (w/ Toyota Safety Sense P)

Hide 86652F 29.INSTALL SKID CONTROL BUZZER (w/ Toyota Safety Sense P)

Hide 30.INSTALL STEERING COLUMN ASSEMBLY

Hide 31.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 33.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION


Hide 88710E 34.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the air conditioner tube and accessory assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the air conditioner tube and accessory assembly.


Hide 88707 35.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.

Compressor Oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction pipe sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly.


e.
E336831

Rotate the hook connector as shown in the illustration.


f.

Insert the hose joint into the fitting hole securely and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245A 36.CONNECT INLET HEATER WATER HOSE A

a.

w/o Exhaust Heat Recirculation System:

i.
E336826C01
1.74,2.823 2.156,2.406 false 0.115,2.229 0.427,2.385 0.313,0.156 10 false *a 2.188,2.292 2.5,2.448 0.313,0.156 10 false *b 2.667,2.813 2.979,2.969 0.313,0.156 10 false *c 1.135,1.208 1.333,1.406 0.198,0.198 10 true A
*a View A
*b Marking (Brown)
*c Clip Installation Angle (60°)


Connect the inlet heater water hose A with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose A.




b.

w/ Exhaust Heat Recirculation System:

i.
E336827C01
1.729,2.802 2.146,2.385 false 0.115,2.219 0.427,2.375 0.313,0.156 10 false *a 2.188,2.26 2.5,2.417 0.313,0.156 10 false *b 2.667,2.833 2.979,2.99 0.313,0.156 10 false *c 1.146,1.125 1.375,1.344 0.229,0.219 10 true A
*a View A
*b Marking (Blue)
*c Clip Installation Angle (60°)


Connect the inlet heater water hose A with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose A.




Hide 87246A 37.CONNECT OUTLET HEATER WATER HOSE A (w/o Exhaust Heat Recirculation System)

a.
E336823C01
1.76,2.823 2.177,2.406 false 0.073,2.188 0.385,2.344 0.313,0.156 10 false *a 2.229,2.271 2.542,2.427 0.313,0.156 10 false *b 0.604,2.823 0.917,2.979 0.313,0.156 10 false *c 0.823,1.021 1.021,1.208 0.198,0.188 10 true A
*a View A
*b Marking (Red)
*c Clip Installation Angle (60°)


Connect the outlet heater water hose A with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose A.



Hide 87207A 38.CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY A (w/ Exhaust Heat Recirculation System)

a.
E336822C01
1.76,2.813 2.177,2.396 false 0.104,2.25 0.417,2.406 0.313,0.156 10 false *a 2.208,2.292 2.521,2.448 0.313,0.156 10 false *b 0.635,2.875 0.948,3.031 0.313,0.156 10 false *c 0.792,1.052 0.99,1.24 0.198,0.188 10 true A
*a View A
*b Marking (Green)
*c Clip Installation Angle (60°)


Connect the water pipe and hose sub-assembly A with the marking facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the water pipe and hose sub-assembly A.



Hide 55701J 39.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55736D 40.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 41.INSTALL WATER GUARD PLATE LH

Hide 55737B 42.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

Hide 55738D 43.INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

Hide 44.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 45.ADD ENGINE COOLANT (for Engine)

Hide 46.INSPECT FOR COOLANT LEAK (for Engine)

Hide 47. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT