Home › Engine / Hybrid System › 2WW EMISSION CONTROL › MONOLITHIC CONVERTER › from 2015.10
RM3090E _51 Engine / Hybrid System _044375 2WW EMISSION CONTROL _0210870 MONOLITHIC CONVERTER A

2WW EMISSION CONTROL  MONOLITHIC CONVERTER  INSTALLATION  


PROCEDURE

Hide 25051 1.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A341668

Temporarily install the manifold stay with the 2 nuts.


b.
A341669C01
2.584,0.073 2.782,0.253 0.198,0.180 10 *4 2.071,0.073 2.269,0.253 0.198,0.180 10 *3 1.616,0.073 1.814,0.253 0.198,0.180 10 *2 1.112,0.073 1.310,0.253 0.198,0.180 10 *1 2.314,1.038 2.429,0.15 2.429,0.15 2.538,0.15 false 1.849,0.806 1.942,0.156 1.942,0.156 2.051,0.156 false 1.393,0.696 1.481,0.165 1.481,0.165 1.59,0.165 false 0.912,0.556 0.983,0.162 0.983,0.162 1.092,0.162 false
*1 Turbocharger Sub-assembly
*2 Gasket
*3 V-band Clamp
*4 Exhaust Manifold Converter Sub-assembly


Temporarily install the exhaust manifold converter sub-assembly and engine bracket with the 3 nuts, 3 bolts, a new V-band clamp and a new gasket.


c.

Tighten the engine bracket with the 3 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.
A341670

Temporarily install the manifold stay with the 2 bolts.


e.
A341671C02
0.74,2.479 0.917,2.479 0.917,2.479 1.271,2.885 false 0.5,2.396 0.698,2.573 0.198,0.177 10 false *1 0.302,3.427 0.635,3.635 0.333,0.208 10 false 20°
*1 V-band Clamp


Align the V-band clamp as shown in the illustration and temporarily install it.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)

HINT:

To prevent the V-band clamp from interfering with the No. 1 manifold converter insulator, temporarily install the V-band clamp at the angle shown in the illustration.



f.
A370937C01
1.031,2.083 1.167,2.083 1.167,2.083 1.583,2.219 true 0.833,1.99 1.021,2.198 0.188,0.208 10 false *1 0.667,2.729 0.865,2.948 0.198,0.219 10 false *a
*1 V-band Clamp
*a Clearance


Tighten the V-band clamp.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


g.

Check the clearance of the V-band clamp.

NOTICE:

Do not reuse a V-band clamp that has been tightened to the specified torque.


HINT:

After tightening the V-band clamp to the specified torque, check that the clearance is within 0 to 3.5 mm (0 to 0.138 in.). If the result is not as specified, reinstall the exhaust manifold converter sub-assembly as the installation position is incorrect.



h.

Tighten the 5 nuts, 2 bolts and exhaust manifold converter sub-assembly in the order shown in the illustration.

A370938N01
6.365,2.906 6.521,3.104 0.156,0.198 10 true 2 3.292,4.042 3.448,4.24 0.156,0.198 10 true 3 2.844,3.469 3,3.646 0.156,0.177 10 true 4 0.406,2.844 0.563,3.042 0.156,0.198 10 true 5 2.042,3.542 2.167,3.74 0.125,0.198 10 true 6 2.104,4.51 2.219,4.698 0.115,0.188 10 true 7 6.125,1.854 6.281,2.052 0.156,0.198 10 true 1

Torque:
for Bolt : 38 N*m (387 kgf*cm, 28 ft.*lbf)
for Nut : 19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 17167 2.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the No. 1 exhaust manifold heat insulator with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Attach the 2 clamps and connect the engine wire.


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length (front) 41.5 mm (1.63 in.)
Minimum Free Length (rear) 38.5 mm (1.52 in.)

If the free length is less than minimum, replace the compression spring.


b.
A181728C95
2.813,1.563 2.688,1.563 2.688,1.563 2.385,1.875 false 1.615,3.188 1.99,3.188 1.99,3.188 1.99,2.313 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 *1 2.854,1.49 3.135,1.698 0.281,0.208 10 *a 1.448,3.104 1.771,3.344 0.323,0.24 10 *2
*1 Exhaust Manifold Converter Sub-assembly and Front Exhaust Pipe Assembly
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in 2 new gaskets until its surface is flush with the exhaust manifold converter sub-assembly and front exhaust pipe sub-assembly.

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




c.

Connect the front exhaust pipe assembly to the 2 exhaust pipe supports.


d.
A258941C17
2.406,0.792 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 false *a 0.573,0.146 0.823,0.302 0.25,0.156 10 false *1 0.573,1.125 0.813,1.313 0.24,0.188 10 false *2 2.698,0.083 2.927,0.26 0.229,0.177 10 false *3
*1 Exhaust Manifold Converter Sub-assembly or Front Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly or tail exhaust pipe assembly
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly to the exhaust manifold converter sub-assembly and tail exhaust pipe assembly with the 4 bolts and 4 compression springs.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:

After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly, front exhaust pipe assembly and tail exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 51442 4.INSTALL NO. 2 ENGINE UNDER COVER

Hide 77641A 5.INSTALL NO. 1 FUEL TANK PROTECTOR

Hide 50819 6.INSTALL FRONT FLOOR COVER

Hide 51441 7.INSTALL NO. 1 ENGINE UNDER COVER

Hide 87100A 8.INSTALL HEATER AND ACCESSORY ASSEMBLY (w/ Combustion Type Power Heater)

Hide 55701J 9.INSTALL OUTER COWL TOP PANEL

a.

Install the outer cowl top panel sub-assembly with the 13 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Attach the clamp to the outer cowl top panel sub-assembly.


Hide 55789D 10.INSTALL NO. 3 COWL TOP PANEL INSULATOR

a.

Install the No. 3 cowl top panel insulator with the 4 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 85110 11.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 89481B 12.INSTALL DIFFERENTIAL PRESSURE SENSOR

Hide 15.INSPECT FOR EXHAUST GAS LEAK

a.

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.