Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.08
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046815 ENGINE ASSEMBLY A

3ZR-FAE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 11212 2.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 6.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51443 8.REMOVE REAR ENGINE UNDER COVER RH

a.
A297336

Remove the 3 clips and rear engine under cover RH.


Hide 51444 9.REMOVE REAR ENGINE UNDER COVER LH

a.
A374191C01
0,0.188 0.313,0.385 0.313,0.198 10 true *A 0.01,2.615 0.323,2.813 0.313,0.198 10 true *B
*A for Half Cover Type
*B for Full Cover Type


for Half Cover Type:

Remove the 3 clips and rear engine under cover LH.


b.

for Full Cover Type:

Remove the 2 clips and rear engine under cover LH.


Hide 50819 10.REMOVE FRONT FLOOR COVER

Hide 11.REMOVE NO. 2 ENGINE UNDER COVER

a.
A332570

Remove the bolt, clip and No. 2 engine under cover.


Hide 14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 15.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 16470 17.REMOVE RADIATOR RESERVOIR ASSEMBLY

a.
A292528

Slide the 2 hose clamps and disconnect the No. 1 and No. 2 water by-pass hoses from the radiator reservoir assembly.


b.

Remove the 2 bolts and radiator reservoir assembly.


Hide 27020 19.REMOVE GENERATOR ASSEMBLY

Hide 16572D 20.DISCONNECT NO. 2 RADIATOR HOSE

Hide 88310 21.DISCONNECT COMPRESSOR ASSEMBLY WITH PULLEY

a.
A270912

Detach the wire harness clamp and disconnect the cooler compressor connector.


b.
A270913

Remove the 2 bolts and 2 nuts.


c.
A270914

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and disconnect the compressor assembly with pulley from the engine.

HINT:

It is not necessary to completely remove the compressor assembly with pulley. With the hoses connected to the compressor assembly with pulley, hang the compressor assembly with pulley on the vehicle body with a rope.



Hide 17705 22.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 23.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 24.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 28800 25.REMOVE BATTERY

Hide 16057 26.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 74431 27.REMOVE BATTERY TRAY

Hide 74414B 29.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 16571C 31.DISCONNECT NO. 1 RADIATOR HOSE

a.
A206127

Slide the hose clamp and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


Hide 23901 32.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A298964

Remove the No 1 fuel pipe clamp, and then disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION


Hide 33.DISCONNECT WIRE HARNESS AND HOSE

a.
A292534

Detach the 2 wire harness clamps and remove the bolt.


b.
A292536

Disconnect the 2 engine room junction block connectors and remove the nut.


c.
A292537

Detach the 2 claws and slide the engine wire, and then disconnect the engine wire from the engine room junction block assembly.


d.

for Manual Transaxle:

i.

Disconnect the terminal cap, and then remove the nut and disconnect the starter wire.

A372379C01
0.313,0.052 0.625,0.25 0.313,0.198 10 false *A 3.458,0.031 3.771,0.229 0.313,0.198 10 true *B
*A w/o Stop and Start System *B w/ Stop and Start System



ii.

Detach the wire harness clamp.


iii.
A314985

Remove the bolt.


iv.

Detach the wire harness clamp to disconnect the engine wire from the manual transaxle assembly.



e.

for CVT:

i.
A343682

Remove the bolt and disconnect the engine wire from the body.


ii.

Disconnect the connector from the battery current sensor.


iii.
A343681C01
1.406,0.656 1.656,0.656 false 1.406,0.948 1.656,0.948 false 1.229,0.583 1.542,0.781 0.313,0.198 10 false *1 1.24,0.865 1.552,1.063 0.313,0.198 10 false *2
*1 Engine Room Main Wire
*2 Engine Wire


Remove the nut and disconnect the engine room main wire and engine wire from the battery positive terminal.



f.
A292538

Slide the hose clamp and disconnect the connector tube hose from the air tube.


g.
A209171

Slide the 2 clamps and disconnect the heater water outlet hose and heater water inlet hose from the heater core.


Hide 33820B 34.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.
C202031

Remove the 2 clips and disconnect the top ends of the transmission control cable assembly from the manual transaxle assembly.


b.
C202030

Remove the 2 clips and disconnect the 2 transmission control cable assemblies from the transmission control cable bracket.


Hide 16267C 35.REMOVE NO. 3 WATER BY-PASS HOSE (for CVT)

a.
A343658

Detach the clamp, slide the 2 hose clamps and remove the No. 3 water by-pass hose.


Hide 33820B 36.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

a.

Move the shift lever to N.


b.
C296239

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


c.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


d.
C296306

Remove the nut and disconnect the transmission control cable assembly from the transmission control cable support.


e.
C316613

Remove the bolt and disconnect the transmission control cable assembly from the rear engine mounting insulator.


Hide 31418 37.DISCONNECT CLUTCH HOSE (for Manual Transaxle)

a.
A296890

Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.


b.

Remove the clip and disconnect the clutch hose from the clutch hose bracket.


Hide 45259A 38.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 39.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 40.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 43502H 41.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 42.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 43.DISCONNECT FRONT SPEED SENSOR LH

Hide 44.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 45.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 46.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 47.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 48.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 49.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 50.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43420G 52.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 89465 54.DISCONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 17410 55.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 56.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 11361J 57.REMOVE FLYWHEEL HOUSING UNDER COVER

Hide 32101A 58.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 51218A 59.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 51217A 60.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Remove the 4 bolts and front suspension member reinforcement RH.


Hide 61.INSTALL ENGINE HANGER

a.
A292543

Disconnect the air fuel ratio sensor connector and detach the clamp to disconnect the fuel tube from the air fuel ratio sensor bracket.


b.

Remove the bolt and air fuel ratio sensor bracket.


c.
A150573C04
0.333,0.677 0.458,0.677 0.458,0.677 0.74,0.823 true 1.75,0.25 1.833,0.25 1.833,0.25 2.615,0.583 true 0.135,0.583 0.417,0.833 0.281,0.25 10 *1 1.552,0.167 1.833,0.333 0.281,0.167 10 *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37021
No. 2 Engine Hanger 12282-37011
Bolt 91552-81050



Hide 62.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A296304

Remove the 6 bolts and front crossmember sub-assembly.


b.

Remove the through bolt, nut and front engine mounting insulator.

A343660C01
0.302,0.042 0.615,0.24 0.313,0.198 10 false *A 3.917,0.052 4.229,0.25 0.313,0.198 10 false *B
*A for Manual Transaxle *B for CVT



c.

Set an engine lifter underneath the engine.

NOTICE:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.
A292541

Remove the bolt and 2 nuts, and disconnect the engine mounting insulator sub-assembly RH.


e.

Remove the bolt and nut, and disconnect the engine mounting insulator LH.

A343661C01
0.323,0.052 0.542,0.25 0.219,0.198 10 true *A 4.188,0.063 4.406,0.26 0.219,0.198 10 true *B
*A for Manual Transaxle *B for CVT



f.
A296308

Remove the 6 bolts and front suspension member rear brace RH and LH.


g.
A296309

Remove the 2 bolts and front suspension crossmember sub-assembly.


h.

Operate the engine lifter and slowly remove the engine from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




i.

Attach an engine sling device and hang the engine with a chain block.


j.
A206115

Remove the through bolt and front suspension crossmember sub-assembly from the engine.

NOTICE:

Do not damage any engine or transaxle components.


HINT:

Raise the engine with transaxle assembly while keeping it level.



Hide 45319A 63.REMOVE STEERING GEAR HEAT INSULATOR (for RHD)

Hide 16282 64.REMOVE NO. 5 WATER BY-PASS HOSE (for CVT)

a.
A336814

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


b.
C315508

Slide the clip and disconnect the No. 5 water by-pass hose from the oil cooler.


c.

Detach the 2 clamps to remove the No. 5 water by-pass hose.


Hide 32943S 65.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (for CVT)

Hide 32943U 66.DISCONNECT NO. 2 TRANSMISSION OIL COOLER HOSE (for CVT)

Hide 33493B 67.REMOVE OIL COOLER (for CVT)

Hide 32913F 68.REMOVE TRANSMISSION OIL COOLER BRACKET (for CVT)

Hide 11363A 70.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 36100 71.REMOVE TRANSFER ASSEMBLY

Hide 30400 72.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 30300 73.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 74.FIX ENGINE ASSEMBLY

a.

Using wooden blocks or plate lift attachments, set the engine on a flat surface.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine is level.

·

Never install attachments to the oil pan of the engine assembly or transmission as doing so may deform the oil pan.

·

Perform this step while supporting the engine assembly using a sling device and chain block.




Hide 32101 75.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 31210 76.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 77.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 78.REMOVE CLUTCH TUBE (for Manual Transaxle)

Hide 31407B 79.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 31400 80.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 13405 81.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 82121 82.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 83.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Install the engine to an engine stand with the bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 43457 84.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A298937

Remove the 3 bolts and drive shaft bearing bracket.


Hide 12371A 85.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A297245C01
0.333,0.302 0.646,0.458 0.313,0.156 10 *A 0.323,1.771 0.635,1.927 0.313,0.156 10 *B
*A for Manual Transaxle
*B for CVT


Remove the 2 bolts, 2 nuts and rear engine mounting insulator.


Hide 12305 86.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A206209

Remove the bolt and radiator reservoir bracket.


b.

Remove the 3 bolts and engine mounting insulator sub-assembly RH.


Hide 12372A 87.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A293521

Remove the bolt and wire harness clamp bracket.


b.

Remove the 4 bolts and engine mounting insulator LH.