Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM3620E _58 Vehicle Interior _076051 METER / GAUGE / DISPLAY _0374621 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150718  Turn Signal Light Circuit Current Below Threshold  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B150718 Turn Signal Light Circuit Current Below Threshold
Diagnosis Condition:

Auxiliary battery voltage is 10 V or more


Malfunction Status:
·

Open in front turn signal light circuit

·

Open in side turn signal light circuit

·

Open in rear turn signal light circuit


·

Headlight unit assembly

·

Headlight ECU sub-assembly

·

Side turn signal light assembly

·

Outer rear view mirror assembly (w/ Power Retract Mirror with Foot Light)

·

Outer mirror retractor (w/ Power Retract Mirror without Foot Light)

·

Rear combination light socket and wire

·

Combination meter assembly

·

Harness or connector

·

Instrument panel junction block assembly

·

Front turn signal light socket



WIRING DIAGRAM

E414706E01
0.375,1.979 2.229,2.25 1.854,0.271 10 false Headlight Unit Assembly LH 0.25,0.865 2,1.115 1.75,0.25 10 false Front Turn Signal Light Bulb 2.135,1.063 2.302,1.281 0.167,0.219 10 false 2 2.115,0.594 2.365,0.792 0.25,0.198 10 false 1 2.688,0.656 3.156,0.958 0.469,0.302 10 false B 2.688,1.156 3.156,1.458 0.469,0.302 10 false B 2.635,0.979 3.104,1.281 0.469,0.302 10 false 13 2.688,0.49 3.156,0.792 0.469,0.302 10 false 9 3.948,1.177 4.417,1.479 0.469,0.302 10 false A11 3.948,0.656 4.417,0.958 0.469,0.302 10 false A11 3.99,0.479 4.458,0.781 0.469,0.302 10 false 11 3.573,0.667 4.042,0.969 0.469,0.302 10 false TNS 3.542,1.177 4.01,1.479 0.469,0.302 10 false GND 2.427,2.167 4.604,2.417 2.177,0.25 10 false Headlight ECU Sub-assembly LH 5.51,0.656 5.927,0.875 0.417,0.219 10 false 4A 6.115,0.677 6.51,0.906 0.396,0.229 10 false LL 1.063,4.167 3.76,4.552 2.698,0.385 10 false Outer Rear View Mirror Assembly LH 1.052,3.542 3.75,3.927 2.698,0.385 10 false A 1.063,3.708 3.76,4.094 2.698,0.385 10 false Side Turn Signal Light Assembly LH 0.771,2.813 1.115,3.146 0.344,0.333 10 false 2 0.719,3.01 1.063,3.344 0.344,0.333 10 false J13 3.729,3 4.073,3.333 0.344,0.333 10 false J13 3.417,3.01 3.76,3.344 0.344,0.333 10 false J14 3.792,2.813 4.135,3.146 0.344,0.333 10 false 1 4.792,2.823 5.135,3.156 0.344,0.333 10 false 14 4.458,2.833 4.802,3.167 0.344,0.333 10 false 14 4.792,3 5.031,3.271 0.24,0.271 10 false 4H 4.458,3.01 4.698,3.281 0.24,0.271 10 false 4N 4.146,4.125 5.802,4.51 1.656,0.385 10 false Instrument Panel Junction Block Assembly 0.406,3.021 0.75,3.354 0.344,0.333 10 false J14 0.417,2.823 0.76,3.156 0.344,0.333 10 false 11 3.438,2.802 3.781,3.135 0.344,0.333 10 false 10 3.781,3.219 4.125,3.552 0.344,0.333 10 false *3 0.74,3.229 1.083,3.563 0.344,0.333 10 false *3 0.427,3.229 0.771,3.563 0.344,0.333 10 false *4 3.458,3.208 3.802,3.542 0.344,0.333 10 false *4 4.802,3.24 5.146,3.573 0.344,0.333 10 false *1 4.469,3.24 4.813,3.573 0.344,0.333 10 false *2 0.073,6.094 2.677,6.333 2.604,0.24 10 false Rear Combination Light Lens and Body LH 0.875,5.333 2.615,5.583 1.74,0.25 10 false Rear Turn Signal Light Bulb 1.479,3.208 3.302,3.646 1.823,0.438 10 false Side Turn Signal Light 4.083,5.052 4.469,5.323 0.385,0.271 10 false TRN 4.25,5.542 4.438,5.792 0.188,0.25 10 false E 4.49,5.531 4.813,5.771 0.323,0.24 10 false 3 4.49,5.052 4.802,5.292 0.313,0.24 10 false 4 2.948,2.917 3.292,3.25 0.344,0.333 10 false 2 1.271,2.917 1.615,3.25 0.344,0.333 10 false 1 2.823,6.063 3.25,6.26 0.427,0.198 10 false N18 2.833,6.271 5.625,6.552 2.792,0.281 10 false Rear Combination Light Socket and Wire LH 6.115,5.115 6.635,5.323 0.521,0.208 10 false TRNL 5.875,5.01 6.094,5.25 0.219,0.24 10 false 5 0.198,6.948 2.302,7.177 2.104,0.229 10 false *1: except LHD, Manual Transaxle 0.198,7.375 2.208,7.604 2.01,0.229 10 false *2: for LHD, Manual Transaxle 2.531,6.958 4.979,7.188 2.448,0.229 10 false *3: w/ Panoramic View Monitor System 2.531,7.365 5.073,7.604 2.542,0.24 10 false *4: w/o Panoramic View Monitor System 5.865,6.542 7.073,6.917 1.208,0.375 10 false G19 5.854,6.729 7.063,7.104 1.208,0.375 10 false Combination Meter Assembly 4.771,0.667 5.24,0.969 0.469,0.302 10 false 4F 4.823,0.479 5.104,0.688 0.281,0.208 10 false 6 5.563,0.479 5.906,0.719 0.344,0.24 10 false 5 4,0.99 4.469,1.292 0.469,0.302 10 false 12 5.885,0.573 6.115,0.792 0.229,0.219 10 false 1 1.052,2.917 1.396,3.25 0.344,0.333 10 false E 3.208,2.917 3.552,3.25 0.344,0.333 10 false B 0.146,1.438 0.365,1.667 0.219,0.229 10 false C 0.167,1.583 2.271,1.802 2.104,0.219 10 false Front Turn Signal Light Socket

E414707E01
0.406,2.25 2.26,2.521 1.854,0.271 10 false Headlight Unit Assembly RH 0.354,1.135 2.094,1.385 1.74,0.25 10 false Front Turn Signal Light Bulb 2.292,1.313 2.76,1.615 0.469,0.302 10 false 2 2.271,0.844 2.74,1.146 0.469,0.302 10 false 1 2.625,0.917 3.094,1.219 0.469,0.302 10 false B 2.635,1.417 3.104,1.719 0.469,0.302 10 false B 2.604,1.219 3.073,1.521 0.469,0.302 10 false 13 2.615,0.74 3.083,1.042 0.469,0.302 10 false 9 3.854,1.438 4.323,1.74 0.469,0.302 10 false A12 3.854,0.927 4.323,1.229 0.469,0.302 10 false A12 3.917,0.729 4.385,1.031 0.469,0.302 10 false 11 3.5,0.938 3.969,1.24 0.469,0.302 10 false TNS 3.49,1.438 3.958,1.74 0.469,0.302 10 false GND 2.635,2.438 4.875,2.635 2.24,0.198 10 false Headlight ECU Sub-assembly RH 5.427,0.917 6.521,1.302 1.094,0.385 10 false 4A 6.021,0.938 6.469,1.156 0.448,0.219 10 false LR 1.031,4.396 3.729,4.781 2.698,0.385 10 false Outer Rear View Mirror Assembly RH 1.063,3.781 3.76,4.167 2.698,0.385 10 false A 0.76,3.094 1.104,3.427 0.344,0.333 10 false 2 0.729,3.271 1.073,3.604 0.344,0.333 10 false I13 3.781,3.083 4.125,3.417 0.344,0.333 10 false 1 4.698,3.083 5.042,3.417 0.344,0.333 10 false 16 4.698,3.271 4.938,3.542 0.24,0.271 10 false 4H 4.365,3.281 4.604,3.552 0.24,0.271 10 false 4N 4.198,4.375 5.854,4.76 1.656,0.385 10 false Instrument Panel Junction Block Assembly 0.406,3.271 0.75,3.604 0.344,0.333 10 false I14 0.427,3.083 0.771,3.417 0.344,0.333 10 false 11 3.438,3.063 3.781,3.396 0.344,0.333 10 false 10 3.781,3.49 4.125,3.823 0.344,0.333 10 false *3 0.76,3.479 1.104,3.813 0.344,0.333 10 false *3 0.427,3.479 0.771,3.813 0.344,0.333 10 false *4 3.458,3.51 3.802,3.844 0.344,0.333 10 false *4 4.708,3.469 5.052,3.802 0.344,0.333 10 false *1 4.385,3.479 4.729,3.813 0.344,0.333 10 false *2 0.51,6.229 2.313,6.615 1.802,0.385 10 false Rear Combination Light Lens and Body RH 0.885,5.469 2.646,5.708 1.76,0.24 10 false Rear Turn Signal Light Blub 1.479,3.458 3.302,3.896 1.823,0.438 10 false Side Turn Signal Light 4.042,5.188 4.698,5.563 0.656,0.375 10 false TRN 4.208,5.677 4.865,6.052 0.656,0.375 10 false E 4.427,5.677 5.083,6.052 0.656,0.375 10 false 3 4.427,5.188 5.083,5.563 0.656,0.375 10 false 4 2.948,3.177 3.292,3.51 0.344,0.333 10 false 2 1.292,3.177 1.635,3.51 0.344,0.333 10 false 1 2.719,6.208 4.698,6.615 1.979,0.406 10 false M14 2.729,6.375 4.625,6.75 1.896,0.375 10 false Rear Combination Light Socket and Wire RH 6.042,5.302 6.51,5.573 0.469,0.271 10 false TRNR 5.792,5.156 6.073,5.344 0.281,0.188 10 false 6 0.198,7.104 2.573,7.406 2.375,0.302 10 false *1: except LHD, Manual Transaxle 0.208,7.49 2.583,7.792 2.375,0.302 10 false *2: for LHD, Manual Transaxle 2.438,7.104 4.969,7.406 2.531,0.302 10 false *3: w/ Panoramic View Monitor System 2.375,7.49 4.906,7.792 2.531,0.302 10 false *4: w/o Panoramic View Monitor System 5.844,6.677 7.052,7.052 1.208,0.375 10 false G19 5.854,6.854 7.063,7.229 1.208,0.375 10 false Combination Meter Assembly 4.708,0.927 5.177,1.229 0.469,0.302 10 false 4F 4.729,0.708 5.198,1.01 0.469,0.302 10 false 8 5.458,0.74 5.927,1.042 0.469,0.302 10 false 4 1.063,3.969 3.76,4.354 2.698,0.385 10 false Side Turn Signal Light Assembly RH 3.427,3.271 3.771,3.604 0.344,0.333 10 false I14 3.74,3.271 4.083,3.604 0.344,0.333 10 false I13 3.906,1.25 4.375,1.552 0.469,0.302 10 false 12 5.802,0.823 6.052,1.073 0.25,0.25 10 false 2 4.375,3.073 4.719,3.406 0.344,0.333 10 false 16 1.052,3.177 1.396,3.51 0.344,0.333 10 false E 3.219,3.177 3.563,3.51 0.344,0.333 10 false B 0.167,1.698 0.417,1.927 0.25,0.229 10 false C 0.177,1.844 2.229,2.042 2.052,0.198 10 false Front Turn Signal Light Socket

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the bulbs before performing the following procedure.

·

If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Front turn signal light LH and side turn signal light LH do not blink. A
Front turn signal light RH and side turn signal light RH do not blink. B
Front turn signal light LH does not blink. C
Side turn signal light LH does not blink. D
Front turn signal light RH does not blink. E
Side turn signal light RH does not blink. F
Rear turn signal light LH does not blink. G
Rear turn signal light RH does not blink. H



A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)

C

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)

D

10.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

E

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)

F

17.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

G

20.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

H

22.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the A11 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-1 (LL) - A11-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-1 (LL) - 4A-5 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the A12 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-2 (LR) - A12-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the 4A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-2 (LR) - 4A-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the A11 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-1 (LL) - A11-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT HEADLIGHT UNIT ASSEMBLY LH

NG

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
7.INSPECT HEADLIGHT UNIT ASSEMBLY LH
a.
E414953C02
1.521,0.26 2,0.531 0.479,0.271 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 1.698,0.292 2.01,0.49 0.313,0.198 10 false B
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)


Remove the headlight unit assembly LH.

for Single Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL

for Triple Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 - C-1 Always Below 1 Ω
B-13 - C-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT SIDE TURN SIGNAL LIGHT SOCKET

NG

8.INSPECT FRONT SIDE TURN SIGNAL LIGHT SOCKET
a.
E414953C01
1.521,0.26 2,0.531 0.479,0.271 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 1.698,0.292 2.01,0.49 0.313,0.198 10 false B
*a Component without harness connected
(to Headlight ECU Sub-assembly LH)


Remove the headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Apply auxiliary battery voltage to the headlight unit assembly LH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → B-9
Auxiliary battery negative (-) → B-13
Turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG

REPLACE FRONT SIDE TURN SIGNAL LIGHT SOCKET

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY LH)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Disconnect the A11 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-6 - A11-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY LH)

NG

12.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY LH)

*1: except LHD, Manual Transaxle

*2: for LHD, Manual Transaxle

*3: w/ Panoramic View Monitor System

*4: w/o Panoramic View Monitor System


a.

Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.


b.

Disconnect the J13*3 or J14*4 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4H-14 - J13-1 (B)*3 Always Below 1 Ω
4H-14 - J14-10 (B)*4 Always Below 1 Ω

for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4N-14 - J13-1 (B)*3 Always Below 1 Ω
4N-14 - J14-10 (B)*4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK (w/ Power Retract Mirror with Foot Light)
OK (w/ Power Retract Mirror without Foot Light)
NG



OK (w/ Power Retract Mirror with Foot Light)

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

OK (w/ Power Retract Mirror without Foot Light)

REPLACE OUTER MIRROR RETRACTOR LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

13.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the A12 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-2 (LR) - A12-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

16.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
14.INSPECT HEADLIGHT UNIT ASSEMBLY RH
a.
E414953C01
1.521,0.26 2,0.531 0.479,0.271 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 1.698,0.292 2.01,0.49 0.313,0.198 10 false B
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)
*b Component without harness connected
(to Front Turn Signal Light Bulb)


Remove the headlight unit assembly RH.

for Single Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Single Beam Headlight)>REMOVAL

for Triple Beam Headlight:

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-9 - C-1 Always Below 1 Ω
B-13 - C-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.INSPECT FRONT SIDE TURN SIGNAL LIGHT SOCKET

NG

15.INSPECT FRONT SIDE TURN SIGNAL LIGHT SOCKET
a.
E414953C01
1.521,0.26 2,0.531 0.479,0.271 0.167,0.115 0.479,0.313 0.313,0.198 10 false *a 1.698,0.292 2.01,0.49 0.313,0.198 10 false B
*a Component without harness connected
(to Headlight ECU Sub-assembly RH)


Remove the headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ECU>REMOVAL


b.

Apply auxiliary battery voltage to the headlight unit assembly RH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → B-9
Auxiliary battery negative (-) → B-13
Turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY RH

NG

REPLACE FRONT SIDE TURN SIGNAL LIGHT SOCKET

16.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - HEADLIGHT ECU SUB-ASSEMBLY RH)
a.

Disconnect the 4F instrument panel junction block assembly connector.


b.

Disconnect the A12 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4F-8 - A12-11 (TNS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY RH)

NG

19.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
18.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - OUTER REAR VIEW MIRROR ASSEMBLY RH)

*1: except LHD, Manual Transaxle

*2: for LHD, Manual Transaxle

*3: w/ Panoramic View Monitor System

*4: w/o Panoramic View Monitor System


a.

Disconnect the 4H*1 or 4N*2 instrument panel junction block assembly connector.


b.

Disconnect the I13*3 or I14*4 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4H-16 - I13-1 (B)*3 Always Below 1 Ω
4H-16 - I14-10 (B)*4 Always Below 1 Ω

for LHD, Manual Transaxle
Tester Connection Condition Specified Condition
4N-16 - I13-1 (B)*3 Always Below 1 Ω
4N-16 - I14-10 (B)*4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK (w/ Power Retract Mirror with Foot Light)
OK (w/ Power Retract Mirror without Foot Light)
NG



OK (w/ Power Retract Mirror with Foot Light)

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

OK (w/ Power Retract Mirror without Foot Light)

REPLACE OUTER MIRROR RETRACTOR RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

20.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N18 rear combination light socket and wire LH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N18-4 (TRN) - G19-5 (TRNL) Always Below 1 Ω
N18-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE LH
a.
E409905C01
1.208,1.844 1.375,1.844 1.375,1.844 1.604,1.552 true 2.313,1.844 2.125,1.844 2.125,1.844 1.802,1.573 true 2.385,1.719 2.844,1.917 0.458,0.198 10 false TRN 1.052,1.719 1.51,1.917 0.458,0.198 10 false E 0.125,0.177 0.583,0.375 0.458,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Socket and Wire LH)


Disconnect the N18 rear combination light socket and wire LH connector.


b.

Apply auxiliary battery voltage to the rear combination light socket and wire LH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 4 (TRN)
Auxiliary battery negative (-) → Terminal 3 (E)
Turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE

22.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M14 rear combination light socket and wire RH connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-4 (TRN) - G19-6 (TRNR) Always Below 1 Ω
M14-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE RH
a.
E409905C01
1.208,1.844 1.375,1.844 1.375,1.844 1.604,1.552 true 2.313,1.844 2.125,1.844 2.125,1.844 1.802,1.573 true 2.385,1.719 2.844,1.917 0.458,0.198 10 false TRN 1.052,1.719 1.51,1.917 0.458,0.198 10 false E 0.125,0.177 0.583,0.375 0.458,0.198 10 false *a
*a Component without harness connected
(Rear Combination Light Socket and Wire RH)


Disconnect the M14 rear combination light socket and wire RH connector.


b.

Apply auxiliary battery voltage to the rear combination light socket and wire RH and check that the light illuminates.

OK:
Condition Specified Condition
Auxiliary battery positive (+) → Terminal 4 (TRN)
Auxiliary battery negative (-) → Terminal 3 (E)
Turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE