Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH › 2019.02–2020.08
RM3620E _59 Vehicle Exterior _077130 LIGHTING (EXT) _0375600 HAZARD WARNING SWITCH A

LIGHTING (EXT)  HAZARD WARNING SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during hazard warning signal switch removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55405B 6.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Hide 55424C 7.REMOVE RADIO TUNER FINISH PANEL (for Audio-less)

Hide 55422C 8.REMOVE CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

Hide 9.REMOVE STEREO OPENING COVER WITH BRACKET (for Audio-less)

Hide 10.REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 11.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 55900 13.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (w/ ECU)

Hide 55434B 14.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 15.REMOVE NAVIGATION ECU WITH BRACKET (w/ ECU, for Navigation System)

Hide 16.REMOVE NAVIGATION ECU WITH BRACKET (w/ ECU, for Dummy Case)

Hide 17.REMOVE TELEPHONE TRANSCEIVER ASSEMBLY WITH BRACKET (w/ ECU, for Telematics Transceiver)

Hide 84330 18.REMOVE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

a.

Place a hand at the rear side of the center register, detach the hazard warning signal switch assembly claw and push towards the rear of the vehicle.

HINT:

Press the hazard warning signal switch assembly from the top and bottom and detach it.


E404113C01
0,0 0,0 false
V113147

Press in this Direction - -



b.
E404115

Disconnect the connector.