Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)
RM27L0U _55 Steering _049327 STEERING COLUMN _0235764 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  INSTALLATION  


PROCEDURE

Hide 45250 1.INSTALL STEERING COLUMN ASSEMBLY

a.
U153636

Install the steering column with the bolt and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Connect the connectors and wire harness clamps.


Hide 45203 2.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C155151E03
0.646,1.615 1.646,1.313 false 0.646,1.615 1.677,1.542 false 0.427,1.51 0.635,1.719 0.208,0.208 10 false *a

Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

Text in Illustration
*a Matchmark


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C155150E03
1.385,1.385 0.635,1.823 false 0.646,1.813 1.719,1.542 false 0.448,1.823 1.448,2.146 1,0.323 10 true *a

Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

Text in Illustration
*a Matchmark


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.
C154524E02
1.25,0.938 0.99,1.708 true 1.094,1.01 0.99,1.688 true 0.844,1.677 1.594,1.854 0.75,0.177 10 false *a

Align the matchmarks on the steering column and steering intermediate shaft.

Text in Illustration
*a Matchmark


d.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


e.
C155149

Install the 3 bolts and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 87201F 4.INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

a.
C154523

Install the air duct with the bolt.


Hide 55046A 7.INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER LH

Hide 53601 8.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 12.INSTALL TILT AND TELESCOPIC MANUAL SWITCH

a.
C159804

Attach the claw to install the tilt and telescopic switch.


b.

Connect the connector.


Hide 45100 16.INSTALL STEERING WHEEL ASSEMBLY

Hide 17.INSPECT STEERING WHEEL CENTER POINT

Hide 45187 19.INSTALL LOWER NO. 3 STEERING WHEEL COVER

Hide 45186 20.INSTALL LOWER NO. 2 STEERING WHEEL COVER

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 23. CUSTOMIZE INFORMATION

a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Utility / Customize Setting / Tilt & Telescopic.


e.

Turn the auto away/return function ON.