Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for LHD)
RM3650E _58 Vehicle Interior _079885 HEATING / AIR CONDITIONING _0387587 AIR CONDITIONING UNIT(for LHD) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for LHD)  INSTALLATION  


PROCEDURE

Hide 87010 1.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Install the air conditioning unit assembly.


b.
I114270

Ensure correct fit of condensate drain (2) on grommet (1).

NOTICE:
·

Damage caused by water ingress into the vehicle.

Water ingress into the vehicle may result in damage to components, malfunctions and corrosion.

-

Perform visual inspection after installing the air conditioning unit assembly (2).

-

Only use undamaged components.





c.
I114268

Tighten T25 screws (1) of air conditioning unit assembly (2).

Torque:
2.8 N*m (29 kgf*cm, 25 in.*lbf)


d.
I114267

Correctly push on the heater water hoses and secure the hose clamps (1).


e.
I114846

Fasten the air conditioning unit assembly with the claws (1).


f.
I114845

Install No. 1 air duct sub-assembly.


g.

Tighten T25 screws (1).

Torque:
2.8 N*m (29 kgf*cm, 25 in.*lbf)


h.
I114844

Connect the connector (1).


i.

Engage the clamps (2).


Hide 55305C 3.INSTALL INSTRUMENT PANEL REINFORCEMENT SUB-ASSEMBLY

a.

Carefully insert the instrument panel reinforcement sub-assembly and connect all connectors at the same time.

NOTICE:

Conduct the following operation with the assistance of a second person.



b.

Install the air conditioning unit assembly to the instrument panel reinforcement sub-assembly first.


c.
I114854

Tighten the nuts in the order shown in the illustration.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.
I114855

Tighten nuts (1).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
I114856

Tighten nuts (1).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


f.

Using a socket wrench 16 mm, tighten bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.
I114857

Tighten bolts (1).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.
I114263

Place the carpet (1) in the marked area to the side and install the No. 1 instrument panel bracket.


i.

Tighten bolt (3).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


j.

Tighten nut (2).

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:
·

The right-hand side component is shown. The procedure on the right is identical.

·

Carry out the work steps on the left and right side.




k.
I114843

Install the cable ducts (2) and engage the claws (1).


l.
I114258

Connect the cable harness and engage the clamps (2).


m.

Connect the connector (1).


n.
I114842

Connect the connector (1).


o.
I114256

Connect the connectors (1).


p.
I114841

Connect the connectors (1).


Hide 45250 4.CONNECT STEERING COLUMN ASSEMBLY

Hide 83108 5.INSTALL METER MIRROR SUB-ASSEMBLY

Hide 55468C 6.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL SEAL

Hide 7.INSTALL RADIO RECEIVER ASSEMBLY (w/o Navigation System)

Hide 8.INSTALL RADIO RECEIVER ASSEMBLY (w/ Navigation System)

Hide 87050C 9.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M21b)

a.
I115235

Install the No. 1 air conditioning radiator damper servo sub-assembly (M21b).


b.

Tighten T20 screws (2).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (1).


Hide 10.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 87050C 11.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M16)

a.
I115230

Install the No. 1 air conditioning radiator damper servo sub-assembly (M16) (2).


b.

Tighten T20 screws (1).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (3).


Hide 55550 12.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55011A 13.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

Hide 87050C 14.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M61)

a.
I115231

Install the No. 1 air conditioning radiator damper servo sub-assembly (M61) (3).


b.

Tighten T20 screws (2).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (1).


Hide 87050C 15.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M7a)

a.
I115232

Install the No. 1 air conditioning radiator damper servo sub-assembly (M7a) (3).


b.

Tighten T20 screws (2).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (1).


Hide 87050C 16.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M69)

a.
I115229

Install the No. 1 air conditioning radiator damper servo sub-assembly (M69) (3).


b.

Tighten T20 screws (1).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (2).


Hide 87103B 17.INSTALL BLOWER WITH FAN MOTOR SUB-ASSEMBLY

Hide 87050C 18.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M23a)

a.
I115234

Install the No. 1 air conditioning radiator damper servo sub-assembly (M23a).


b.

Tighten T20 screws (2).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (1).


Hide 87050C 19.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (M83a)

a.
I115233

Install the No. 1 air conditioning radiator damper servo sub-assembly (M83a) (3).


b.

Tighten T20 screws (1).

Torque:
1.2 N*m (12 kgf*cm, 11 in.*lbf)


c.

Connect the connector (2).


Hide 87211 20.INSTALL NO. 1 AIR DUCT

a.

Install No. 1 air duct.


b.

Tighten screw.

Torque:
2.8 N*m (29 kgf*cm, 25 in.*lbf)


Hide 87211A 21.INSTALL NO. 2 AIR DUCT

a.

Install No. 2 air duct.


b.

Tighten screw.

Torque:
2.8 N*m (29 kgf*cm, 25 in.*lbf)


Hide 73990 22.INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 73900 23.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 55606 24.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55607 25.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 88710 26.CONNECT AIR CONDITIONER TUBE ASSEMBLY

a.

Replace O-rings.


b.

Install the air conditioner tube assembly on the cooler expansion valve.


c.

Tighten nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.
I114858

Thread the heater water hose into the receptacle of the air conditioner tube assembly (2) in the direction of the arrow.


e.

Engage the catch (1).


f.
I114838

Connect the heater water hose (2) and (3) in the holder with the catches (1).

HINT:

Check holder with catches (1) for damage, replace if necessary.



g.

Engage the notches (1).


h.
I114837

Install the air conditioner tube assembly (2) and the heater water hose (3) in the holder.


i.

Engage the notches (1).


j.
I114836

Replace O-rings.


k.

Install the suction pipe sub-assembly (4) and tighten the T45 bolt (3).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


l.

Install the air conditioner tube assembly (2) and tighten the T30 bolt (1).

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 53681 32.INSTALL UPPER CENTER FRONT SUSPENSION BRACE

Hide 33.ADD ENGINE COOLANT (for B48)

Hide 34.ADD ENGINE COOLANT (for B58)

Hide 35. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 36. CHECK WIPER AND WASHER SYSTEM