Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC Code
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Harness or connector
  3. Stereo component amplifier assembly (except 4 speakers)
  4. Navigation receiver assembly

WIRING DIAGRAM


E282414E02


E282415E02


E282416E03


E282417E02


E282418E04


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK VEHICLE CONDITION
  1. Check the vehicle condition.
    Result 
    Result
    Proceed to
    for 4 Speakers
    A
    for 7 or 9 Speakers
    B
    for 12 Speakers
    C



B
Go to step 6

C
Go to step 13
A


3.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the J133 navigation receiver assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J133-1 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J133-5 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    M8-1 - J147-1 (+)
    Always
    Below 1 Ω
    M8-2 - J147-4 (-)
    Always
    Below 1 Ω
    J133-2 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J133-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    N10-1 - J149-1 (+)
    Always
    Below 1 Ω
    N10-2 - J149-4 (-)
    Always
    Below 1 Ω
    J133-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    J133-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    M8-2 - Body ground
    Always
    10 kΩ or higher
    M8-1 - Body ground
    Always
    10 kΩ or higher
    J133-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    J133-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    N10-2 - Body ground
    Always
    10 kΩ or higher
    N10-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

6.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  3. *3: for 9 Speakers
  1. Disconnect the J133 and J134 navigation receiver assembly connector.

  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.

  1. Disconnect the J150 front No. 4 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.*3

  1. Disconnect the J144 and J145 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M8-1 - J144-1 (R+)
    Always
    Below 1 Ω
    M8-2 - J144-5 (R-)
    Always
    Below 1 Ω
    N10-1 - J144-2 (L+)
    Always
    Below 1 Ω
    N10-2 - J144-6 (L-)
    Always
    Below 1 Ω
    O1-1 - J145-4 (WFR+)
    Always
    Below 1 Ω
    O1-2 - J145-11 (WFR-)
    Always
    Below 1 Ω
    O7-1 - J145-5 (WFL+)
    Always
    Below 1 Ω
    O7-2 - J145-12 (WFL-)
    Always
    Below 1 Ω
    O2-3 - J145-9 (RR+)*3
    Always
    Below 1 Ω
    O2-2 - J145-10 (RR-)*3
    Always
    Below 1 Ω
    J145-9 (RR+) - J134-1 (RR+)
    Always
    Below 1 Ω
    J145-10 (RR-) - J134-3 (RR-)
    Always
    Below 1 Ω
    O8-3 - J145-3 (RL+)*3
    Always
    Below 1 Ω
    O8-2 - J145-8 (RL-)*3
    Always
    Below 1 Ω
    J145-3 (RL+) - J134-2 (RL+)
    Always
    Below 1 Ω
    J145-8 (RL-) - J134-6 (RL-)
    Always
    Below 1 Ω
    J145-2 (FR+) - J133-1 (FR+)
    Always
    Below 1 Ω
    J145-7 (FR-) - J133-5 (FR-)
    Always
    Below 1 Ω
    J145-1 (FL+) - J133-2 (FL+)
    Always
    Below 1 Ω
    J145-6 (FL-) - J133-6 (FL-)
    Always
    Below 1 Ω
    J145-2 (FR+) - J147-3 (TWR+)
    Always
    Below 1 Ω
    J145-7 (FR-) - J147-2 (TWR-)
    Always
    Below 1 Ω
    J145-1 (FL+) - J149-3 (TWL+)
    Always
    Below 1 Ω
    J145-6 (FL-) - J149-2 (TWL-)
    Always
    Below 1 Ω
    J147-1 (+) - J150-1 (+)
    Always
    Below 1 Ω
    J147-4 (-) - J150-4 (RI1-)
    Always
    Below 1 Ω
    J150-2 (-) - J149-4 (-)
    Always
    Below 1 Ω
    J150-3 (RI1+) - J149-1 (+)
    Always
    Below 1 Ω
    J144-1 (R+) - Body ground
    Always
    10 kΩ or higher
    J144-5 (R-) - Body ground
    Always
    10 kΩ or higher
    J144-2 (L+) - Body ground
    Always
    10 kΩ or higher
    J144-6 (L-) - Body ground
    Always
    10 kΩ or higher
    J145-4 (WFR+) - Body ground
    Always
    10 kΩ or higher
    J145-11 (WFR-) - Body ground
    Always
    10 kΩ or higher
    J145-5 (WFL+) - Body ground
    Always
    10 kΩ or higher
    J145-12 (WFL-) - Body ground
    Always
    10 kΩ or higher
    J145-9 (RR+) - Body ground
    Always
    10 kΩ or higher
    J145-10 (RR-) - Body ground
    Always
    10 kΩ or higher
    J145-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    J145-8 (RL-) - Body ground
    Always
    10 kΩ or higher
    J145-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    J145-7 (FR-) - Body ground
    Always
    10 kΩ or higher
    J145-1 (FL+) - Body ground
    Always
    10 kΩ or higher
    J145-6 (FL-) - Body ground
    Always
    10 kΩ or higher
    J147-1 (+) - Body ground
    Always
    10 kΩ or higher
    J147-4 (-) - Body ground
    Always
    10 kΩ or higher
    J147-3 (TWR+) - Body ground
    Always
    10 kΩ or higher
    J147-2 (TWR-) - Body ground
    Always
    10 kΩ or higher
    J150-2 (-) - Body ground
    Always
    10 kΩ or higher
    J150-3 (RI1+) - Body ground
    Always
    10 kΩ or higher
    J149-3 (TWL+) - Body ground
    Always
    10 kΩ or higher
    J149-2 (TWL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the front No. 1 speaker assembly.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)

C
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
A


8.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 9
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

9.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 10
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE) 

10.CHECK REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here

  1. Inspect the rear No. 1 speaker assembly with a known good one.

    1. for Double Cab: Click here
    2. for CrewMax: Click here
    Result 
    Result
    Proceed to
    OK (for CrewMax)
    A
    OK (for Double Cab)
    B
    NG (for Double Cab)
    C
    NG (for CrewMax)
    D



B
Go to step 12

C
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)

D
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
A


11.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 12
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

12.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Double Cab)
    B
    NG (for CrewMax)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE) 

13.CHECK HARNESS AND CONNECTOR (SPEAKER CIRCUIT)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.

  1. Disconnect the J146*1 and/or J148*2 front No. 2 speaker assembly connector.

  1. Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.

  1. Disconnect the J150 front No. 4 speaker assembly connector.

  1. Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.

  1. Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.

  1. Disconnect the P14 No. 1 box speaker assembly connector.

  1. Disconnect the J142 and J143 stereo component amplifier assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J142-2 (FR+) - J146-3 (TWR+)
    Always
    Below 1 Ω
    J142-6 (FR-) - J146-4 (TWR-)
    Always
    Below 1 Ω
    J146-1 (+) - M1-3
    Always
    Below 1 Ω
    J146-2 (-) - M1-2
    Always
    Below 1 Ω
    J143-9 (WFR+) - M8-1
    Always
    Below 1 Ω
    J143-3 (WFR-) - M8-2
    Always
    Below 1 Ω
    J142-10 (RR+) - O2-3 (+TW)
    Always
    Below 1 Ω
    J142-4 (RR-) - O2-2 (-TW)
    Always
    Below 1 Ω
    O2-4 (+) - O1-2
    Always
    Below 1 Ω
    O2-1 (-) - O1-1
    Always
    Below 1 Ω
    J142-5 (WF1+) - P14-1
    Always
    Below 1 Ω
    J142-12 (WF1-) - P14-2
    Always
    Below 1 Ω
    J142-3 (RL+) - O8-3 (+TW)
    Always
    Below 1 Ω
    J142-9 (RL-) - O8-2 (-TW)
    Always
    Below 1 Ω
    O8-4 (+) - O7-1
    Always
    Below 1 Ω
    O8-1 (-) - O7-2
    Always
    Below 1 Ω
    J143-2 (WFL+) - N10-1
    Always
    Below 1 Ω
    J143-1 (WFL-) - N10-2
    Always
    Below 1 Ω
    J142-8 (FL+) - J148-3 (TWL+)
    Always
    Below 1 Ω
    J142-7 (FL-) - J148-4 (TWL-)
    Always
    Below 1 Ω
    J148-1 (+) - N1-3
    Always
    Below 1 Ω
    J148-2 (-) - N1-2
    Always
    Below 1 Ω
    J143-4 (CTR+) - J150-1
    Always
    Below 1 Ω
    J143-10 (CTR-) - J150-2
    Always
    Below 1 Ω
    J142-2 (FR+) - Body ground
    Always
    10 kΩ or higher
    J142-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    J146-1 (+) - Body ground
    Always
    10 kΩ or higher
    J146-2 (-) - Body ground
    Always
    10 kΩ or higher
    J143-9 (WFR+) - Body ground
    Always
    10 kΩ or higher
    J143-3 (WFR-) - Body ground
    Always
    10 kΩ or higher
    J142-10 (RR+) - Body ground
    Always
    10 kΩ or higher
    J142-4 (RR-) - Body ground
    Always
    10 kΩ or higher
    O2-4 (+) - Body ground
    Always
    10 kΩ or higher
    O2-1 (-) - Body ground
    Always
    10 kΩ or higher
    J142-5 (WF1+) - Body ground
    Always
    10 kΩ or higher
    J142-12 (WF1-) - Body ground
    Always
    10 kΩ or higher
    J142-3 (RL+) - Body ground
    Always
    10 kΩ or higher
    J142-9 (RL-) - Body ground
    Always
    10 kΩ or higher
    O8-4 (+) - Body ground
    Always
    10 kΩ or higher
    O8-1 (-) - Body ground
    Always
    10 kΩ or higher
    J143-2 (WFL+) - Body ground
    Always
    10 kΩ or higher
    J143-1 (WFL-) - Body ground
    Always
    10 kΩ or higher
    J142-8 (FL+) - Body ground
    Always
    10 kΩ or higher
    J142-7 (FL-) - Body ground
    Always
    10 kΩ or higher
    J148-1 (+) - Body ground
    Always
    10 kΩ or higher
    J148-2 (-) - Body ground
    Always
    10 kΩ or higher
    J143-4 (CTR+) - Body ground
    Always
    10 kΩ or higher
    J143-10 (CTR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


15.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 16
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

16.CHECK FRONT NO. 4 SPEAKER ASSEMBLY
  1. Replace the front No. 4 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
Go to step 17
OK

END (FRONT NO. 4 SPEAKER ASSEMBLY IS DEFECTIVE) 

17.CHECK FRONT NO. 3 SPEAKER ASSEMBLY
  1. Replace the front No. 3 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    2. Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 18
OK

END (FRONT NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE) 

18.CHECK NO. 1 BOX SPEAKER ASSEMBLY
  1. Remove the No. 1 box speaker assembly (Click here).

  1. Inspect the No. 1 box speaker assembly (Click here).



NG
REPLACE NO. 1 BOX SPEAKER ASSEMBLY
OK


19.CHECK REAR NO. 1 SPEAKER ASSEMBLY
  1. Remove the rear No. 1 speaker assembly (Click here).

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR NO. 1 SPEAKER ASSEMBLY (Click here)
OK


20.CHECK REAR NO. 2 SPEAKER ASSEMBLY
  1. Replace the rear No. 2 speaker assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    NOTICE:
    1. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    2. Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
Go to step 21
OK

END (REAR NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

21.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a known good one (Click here).

  1. Check that the malfunction disappears.

    OK:
    Malfunction disappears.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Column Shift Type)
    B
    NG (for Floor Shift Type)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)