CAN COMMUNICATION SYSTEM > Short to B+ in CAN Bus Line |
| Symptom | Trouble Area |
| The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ. |
|


| 1.PRECAUTION |
| NEXT | |
| 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire and CAN branch wire.
| NEXT | |
| 3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE) |
![]() |
Disconnect the J75 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J17-6 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J17-14 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 4.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the J74 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J17-6 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J17-14 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of DLC3 |
|
| ||||
| OK | |
| 6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-1 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-12 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-2 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-13 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 8.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-5 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-16 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-6 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-17 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-3 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-14 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| OK (w/ Audio and Visual System) | A |
| OK (w/ Navigation System) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-7 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-18 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J74-7 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J74-18 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 13.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
![]() |
Disconnect the J19 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J19-11 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J19-12 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Air Conditioning Amplifier Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 15.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (4WD CONTROL ECU) |
![]() |
Disconnect the A25 4WD control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A25-23 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| A25-22 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to 4WD Control ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 17.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BUS BUFFER ECU) |
![]() |
Disconnect the J59 bus buffer ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J59-3 (CAN+) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J59-2 (CAN-) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Bus Buffer ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 19.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY ECU) |
![]() |
Disconnect the J123 network gateway ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J123-16 (CA1H) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J123-15 (CA1L) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Network Gateway ECU) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 21.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 22.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM) |
![]() |
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A24-10 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| A24-11 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to ECM) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| OK (for 1GR-FE) | A |
| OK (for 1UR-FE) | B |
| OK (for 3UR-FE) | C |
| OK (for 3UR-FBE) | D |
| NG | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 23.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 24.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY) |
![]() |
Disconnect the J139 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J139-9 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J139-10 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
|
| ||||
|
| ||||
| A | ||
| ||
| 25.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 26.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY) |
![]() |
Disconnect the J135 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J135-9 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J135-10 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Navigation Receiver Assembly) |
| *b | Front view of DLC3 |
|
| ||||
|
| ||||
| A | ||
| ||
| 27.CONNECT CONNECTOR |
Reconnect the J74 No. 2 junction connector.
| NEXT | |
| 28.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
![]() |
Disconnect the J75 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-1 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-12 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 29.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-3 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-14 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 30.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-5 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-16 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 31.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-6 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-17 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 32.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-8 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-19 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | |
| 33.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J75-4 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J75-15 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 34.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY) |
![]() |
Disconnect the J46 center airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J46-13 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J46-22 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Center Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
| Result | Proceed to |
| OK (for Column Shift Type) | A |
| OK (for Floor Shift Type) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 36.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU) |
![]() |
Disconnect the J2 main body ECU (driver side junction block assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J2-5 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J2-6 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Main Body ECU [Driver Side Junction Block Assembly]) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 38.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 39.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING ANGLE SENSOR) |
![]() |
Disconnect the J6 steering angle sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J6-10 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J6-9 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Steering Angle Sensor) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 40.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU) |
![]() |
Disconnect the A17 brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A7-12 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| A7-13 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector (to Brake Actuator Assembly [Skid Control ECU]) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||
| 42.CONNECT CONNECTOR |
Reconnect the J75 No. 1 junction connector.
| NEXT | |
| 43.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY) |
![]() |
Disconnect the J28 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J28-39 (CANH) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| J28-40 (CANL) - J17-16 (BAT) | Ignition switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector (to Combination Meter Assembly) |
| *b | Front view of DLC3 |
|
| ||||
| OK | ||
| ||