Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Short to GND in CAN Bus Line

for Preparation Click here


DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short between CAN bus lines and GND
  2. Combination meter assembly
  3. Center airbag sensor assembly
  4. Main body ECU (driver side junction block assembly)
  5. Steering angle sensor
  6. Brake actuator assembly (skid control ECU)
  7. Air conditioning amplifier assembly
  8. 4WD control ECU*1
  9. Bus buffer ECU*2
  10. Network gateway ECU*3
  11. Radio and display receiver assembly*4
  12. Navigation receiver assembly*5
  13. ECM
  14. No. 1 junction connector
  15. No. 2 junction connector
  16. DLC3 CAN branch wire or connector
  1. *1: for 4WD
  2. *2: w/ Bus Buffer ECU
  3. *3: w/ Blind Spot Monitor System
  4. *4: w/ Audio and Visual System
  5. *5: w/ Navigation System

WIRING DIAGRAM


C289526E01


C288311E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click here).

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

1.PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the CAN main wire and CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)


    C253362E27
  1. Disconnect the J75 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR)


    C253362E27
  1. Disconnect the J74 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J17-6 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J17-14 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 27
OK


6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C288300E57
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-1 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-12 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 13
OK


7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - 4WD CONTROL ECU)

NOTICE:
For vehicles without a 4WD, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Bus Buffer ECU)".



    C288300E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-2 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-13 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 15
OK


8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - BUS BUFFER ECU)

NOTICE:
For vehicles without a bus buffer ECU, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - Network Gateway ECU)".



    C288300E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-5 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-16 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 17
OK


9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NOTICE:
For vehicles without a blind spot monitor system, go to "Check for Short to GND in CAN Bus Wire (No. 2 Junction Connector - ECM)".



    C288300E60
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-6 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-17 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK


10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM)


    C288300E61
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-3 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-14 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Audio and Visual System)
    A
    OK (w/ Navigation System)
    B
    NG
    C



B
Go to step 12

C
Go to step 21
A


11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)


    C288300E62
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-7 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-18 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 23
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NAVIGATION RECEIVER ASSEMBLY)


    C288300E62
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J74-7 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J74-18 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 25
OK

REPLACE NO. 2 JUNCTION CONNECTOR 

13.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)


    C242944E05
  1. Disconnect the J19 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J19-11 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J19-12 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Air Conditioning Amplifier Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

15.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (4WD CONTROL ECU)


    C289529E02
  1. Disconnect the A25 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-23 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    A25-22 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to 4WD Control ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CANH, CANL)
OK

REPLACE 4WD CONTROL ECU (Click here)  

17.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BUS BUFFER ECU)


    C289530E02
  1. Disconnect the J59 bus buffer ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J59-3 (CAN+) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J59-2 (CAN-) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Bus Buffer ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO BUS BUFFER ECU (CAN+, CAN-)
OK

REPLACE BUS BUFFER ECU 

19.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NETWORK GATEWAY ECU)


    C242947E06
  1. Disconnect the J123 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J123-16 (CA1H) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J123-15 (CA1L) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)  

21.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)


    C242948E04
  1. Disconnect the A24 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-10 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    A24-11 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1UR-FE)
    B
    OK (for 3UR-FE)
    C
    OK (for 3UR-FBE)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)  

23.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)


    C235427E15
  1. Disconnect the J139 radio and display receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J139-9 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J139-10 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

25.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


26.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY)


    C235427E16
  1. Disconnect the J135 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J135-9 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J135-10 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NAVIGATION RECEIVER ASSEMBLY (CANH, CANL)
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

27.CONNECT CONNECTOR
  1. Reconnect the J74 No. 2 junction connector.


NEXT


28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)


    C288300E63
  1. Disconnect the J75 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-1 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-12 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


29.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)


    C288300E64
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-3 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-14 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 34
OK


30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)


    C288300E65
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-5 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-16 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 36
OK


31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)


    C288300E66
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-6 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-17 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 38
OK


32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)


    C288300E67
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-8 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-19 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 40
OK


33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)


    C288300E68
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J75-4 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J75-15 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 42
OK

REPLACE NO. 1 JUNCTION CONNECTOR 

34.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


35.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)


    C242951E04
  1. Disconnect the J46 center airbag sensor assembly connector.

    1. for Column Shift Type: Click here
    2. for Floor Shift Type: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J46-13 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J46-22 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Center Airbag Sensor Assembly)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for Column Shift Type)
    A
    OK (for Floor Shift Type)
    B
    NG
    C



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)  

36.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


37.CHECK FOR SHORT TO GND IN CAN BUS WIRE (MAIN BODY ECU)


    C242953E07
  1. Disconnect the J2 main body ECU (driver side junction block assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J2-5 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J2-6 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Driver Side Junction Block Assembly])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) 

38.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


39.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)


    C242952E04
  1. Disconnect the J6 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J6-10 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J6-9 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Steering Angle Sensor)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE STEERING ANGLE SENSOR (Click here)  

40.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


41.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)


    C242958E04
  1. Disconnect the A17 brake actuator assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-12 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    A7-13 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Actuator Assembly [Skid Control ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)  

42.CONNECT CONNECTOR
  1. Reconnect the J75 No. 1 junction connector.


NEXT


43.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)


    C242945E12
  1. Disconnect the J28 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    J28-39 (CANH) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher
    J28-40 (CANL) - J17-4 (CG)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)