Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051493 METER / GAUGE / DISPLAY _0248310 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

w/ VSC (for Built-in Type Yaw Rate Sensor)

The meter CPU receives vehicle speed signals from the brake actuator assembly via the CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly. The brake actuator assembly supplies power to the vehicle speed sensor. The brake actuator assembly detects vehicle speed signals based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Vehicle Stability Control System (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).




w/ VSC (for Separate Type Yaw Rate Sensor)

The meter CPU receives vehicle speed signals from the brake actuator assembly via the CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly. The brake actuator assembly supplies power to the vehicle speed sensor. The brake actuator assembly detects vehicle speed signals based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Vehicle Stability Control System (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).




w/o VSC (w/ ABS)

The combination meter assembly controls the speedometer in accordance with vehicle speed signals from brake actuator assembly.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Anti-lock Brake System (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).




w/o VSC (w/o ABS)

The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speed sensor.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).



WIRING DIAGRAM

E346310E01
0.073,0.031 1.365,0.271 1.292,0.24 12 false w/ VSC: 0.115,3.156 1.875,3.365 1.76,0.208 10 false Brake Actuator Assembly 2.927,3.219 4.688,3.427 1.76,0.208 10 false : CAN Communication Line 5.292,3.156 7.156,3.354 1.865,0.198 10 false Combination Meter Assembly

E231157E01
0.087,0.051 2.027,0.514 1.939,0.463 12 w/o VSC: 0.881,1.994 1.148,2.140 0.267,0.146 10 A55 1.789,1.194 2.076,1.341 0.288,0.147 10 SP1 2.125,1.095 2.309,1.243 0.184,0.147 10 22 3.092,1.095 3.258,1.243 0.166,0.147 10 *1 3.603,2.433 3.769,2.581 0.166,0.147 10 *2 0.994,4.262 1.278,4.409 0.284,0.147 10 B85 0.994,4.416 2.348,4.563 1.355,0.147 10 Speedometer Sensor 0.881,2.132 2.478,2.279 1.597,0.147 10 Brake Actuator Assembly 1.824,3.4 2.083,3.547 0.259,0.147 10 IG+ 1.852,3.708 2.056,3.856 0.205,0.147 10 SE 2.139,3.628 2.312,3.775 0.173,0.147 10 2 1.894,3.148 2.067,3.295 0.173,0.147 10 SI 2.139,3.32 2.312,3.467 0.173,0.147 10 1 2.139,3.067 2.312,3.215 0.173,0.147 10 3 5.767,4.433 7.048,4.581 1.281,0.147 10 *2: w/o ABS 5.767,4.125 7.048,4.272 1.281,0.147 10 *1: w/ ABS 4.48,2.009 4.764,2.156 0.284,0.147 10 F1 4.48,2.163 6.335,2.310 1.855,0.147 10 Combination Meter Assembly 5.009,1.191 5.182,1.338 0.173,0.147 10 SI 4.82,1.111 4.993,1.258 0.173,0.147 10 5 4.385,3.413 5.983,3.560 1.598,0.147 10 from ECU-IG NO. 2 Fuse

CAUTION / NOTICE / HINT

CAUTION:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
w/ VSC A
w/o VSC (w/ ABS) B
w/o VSC (w/o ABS) C



A

2.CHECK CAN COMMUNICATION SYSTEM

B

6.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)

C

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.



Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output (except Separate Type Yaw Rate Sensor) B
CAN communication DTC is output (for Separate Type Yaw Rate Sensor) C



A

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)

B

C

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200, 240 (km/h) Vehicle is stopped and the engine idling

OK:

Speedometer indication is normal.




OK

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED METER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed/
Min.: 0 (0)
Max.: 255 (158)
Approximately same as actual vehicle speed (When vehicle is being driven) Unit: km/h (mph)

OK:

Vehicle speed displayed on the intelligent tester is almost the same as the speedometer indication.




OK

5.CHECK VEHICLE STABILITY CONTROL SYSTEM

NG

REPLACE COMBINATION METER ASSEMBLY

5.CHECK VEHICLE STABILITY CONTROL SYSTEM
a.

Check if a vehicle stability control DTC is output.



Result
Result Proceed to
Vehicle stability control DTC is not output A
Vehicle stability control DTC is output (for Built-in Type Yaw Rate Sensor) B
Vehicle stability control DTC is output (for Separate Type Yaw Rate Sensor) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

6.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Maximum wheel speed sensor reading
Min.: 0 km/h
Max.: 326 km/h
Actual vehicle speed Speed indicated on speedometer

OK:

Vehicle speed displayed on the intelligent tester is approximately the same as the actual vehicle speed.




OK

7.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

7.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
U158546E01
1.133,0.738 1.429,0.895 0.295,0.156 10 A55 0.095,0.067 0.391,0.223 0.295,0.156 10 *a 1.169,2.901 1.588,3.058 0.420,0.156 10 SP1 1.663,2.148 1.307,2.874 false

Disconnect the A55 brake actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A55-22 (SP1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to brake actuator assembly)


c.

Reconnect the A55 brake actuator assembly connector.



OK

8.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION METER ASSEMBLY)
8.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
U158628E01
0.135,2.265 0.298,2.410 0.163,0.145 10 *b 0.135,0.718 0.298,0.863 0.163,0.145 10 *a 1.703,1.985 1.943,2.131 0.239,0.145 10 SI 1.673,1.418 1.776,1.955 false 1.143,0.736 1.322,0.917 0.179,0.181 10 F1 3.018,3.545 3.348,3.690 0.330,0.145 10 GND

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F1-5 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Standard:
Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the cycle of the waveform narrows.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

REPLACE COMBINATION METER ASSEMBLY

B

C

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the A55 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-5 (SI) - A55-22 (SP1) Always Below 1 Ω
F1-5 (SI) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200, 240 (km/h) Vehicle is stopped and the engine idling

OK:

Speedometer indication is normal.




OK

11.INSPECT SPEEDOMETER SENSOR

NG

REPLACE COMBINATION METER ASSEMBLY

11.INSPECT SPEEDOMETER SENSOR

OK

12.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)

NG

12.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the F1 combination meter assembly connector.


b.

Disconnect the B85 speedometer sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-5 (SI) - B85-3 (SI) Always Below 1 Ω
B85-2 (SE) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B85-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



f.

Reconnect the speedometer sensor connector.



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR