1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
51441C
3.REMOVE ENGINE UNDER COVER RH
11212
4.REMOVE NO. 2 CYLINDER HEAD COVER
19500D
5.REMOVE NO. 1 IGNITION COIL
12261
6.DISCONNECT VENTILATION HOSE
23820
7.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY
11201
8.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
9.INSPECT VALVE CLEARANCE
Inspect the valve clearance when the engine is cold.
Set the No. 1 cylinder to TDC/compression.
| *a | Timing Notch |
| *b | Timing Mark "0" |
Turn the crankshaft damper sub-assembly and align its timing notch with the timing mark "0" of the oil pump assembly.
| *a | Timing Mark |
Check that both timing marks on the camshaft timing sprocket and camshaft timing gear assembly are facing upward, as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
Check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
0.15 to 0.25 mm (0.006 to 0.010 in.)
0.25 to 0.35 mm (0.010 to 0.014 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.
Turn the crankshaft 1 complete revolution (360°) and align its timing notch with the timing mark "0" of the oil pump assembly.
Check the valves indicated in the illustration.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
0.15 to 0.25 mm (0.006 to 0.010 in.)
0.25 to 0.35 mm (0.010 to 0.014 in.)
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifter.
10.ADJUST VALVE CLEARANCE
Remove the engine mounting insulator sub-assembly RH.
Click hereEngine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>REMOVAL
Remove the No. 2 camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL
Remove the camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL
Remove the 16 valve lifters from the cylinder head sub-assembly.
Using a micrometer, measure the thickness of the removed valve lifter.
Calculate the thickness of a new valve lifter so that the valve clearance comes to within the specified values.
| A | Thickness of new valve lifter |
| B | Thickness of used valve lifter |
| C | Measured valve clearance |
Intake A = B + (C - 0.20 mm (0.008 in.))
Exhaust A = B + (C - 0.30 mm (0.012 in.))
Select a new valve lifter with a thickness as close to the calculated values as possible.
Valve lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).
| *a | Measured clearance
mm (in.) |
*b | Installed valve lifter thickness
mm (in.) |
0.15 to 0.25 mm (0.006 to 0.010 in.)
A 5.250 mm (0.2067 in.) valve lifter is installed, and measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) valve lifter with a new No. 46 valve lifter.
| Valve Lifter No. | Thickness | Valve Lifter No. | Thickness | Valve Lifter No. | Thickness |
|---|---|---|---|---|---|
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700(0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
| *a | Measured clearance
mm (in.) |
*b | Installed valve lifter thickness
mm (in.) |
0.25 to 0.35 mm (0.010 to 0.014 in.)
A 5.340 mm (0.2102 in.) valve lifter is installed, and measured clearance is 0.440 mm (0.0173 in.). Replace the 5.340 mm (0.2102 in.) valve lifter with a new No. 48 valve lifter.
| Valve Lifter No. | Thickness | Valve Lifter No. | Thickness | Valve Lifter No. | Thickness |
|---|---|---|---|---|---|
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
Install the selected valve lifter to the cylinder head sub-assembly.
Install the camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION
Install the No. 2 camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION
Install the engine mounting insulator sub-assembly RH.
Click hereEngine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>INSTALLATION
11201
11.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
23820
12.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
12261
13.CONNECT VENTILATION HOSE
19500D
14.INSTALL NO. 1 IGNITION COIL
15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
16.INSPECT FOR ENGINE OIL LEAK
11212
17.INSTALL NO. 2 CYLINDER HEAD COVER
51441C
18.INSTALL ENGINE UNDER COVER RH