Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for Manual Transaxle) › from 2018.01
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262363 ENGINE ASSEMBLY(for Manual Transaxle) A

2NR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for Manual Transaxle)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A382175C01
2.385,0.969 3.104,1.271 0.719,0.302 10 true 1 (*a), 6 0.792,0.583 1.385,0.802 0.594,0.219 10 true 2 (*a), 7 1.406,1.781 1.563,1.979 0.156,0.198 10 true 3 1.354,1.354 1.51,1.552 0.156,0.198 10 true 4 2.219,1.646 2.375,1.844 0.156,0.198 10 true 5
*a Temporarily Tighten


Engage the hook and temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 5 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A382174C01
2.146,0.469 2.792,0.698 0.646,0.229 10 true 1 (*a), 4 0.958,1.885 1.115,2.083 0.156,0.198 10 true 2 1.573,0.573 1.729,0.771 0.156,0.198 10 true 3
*a Temporarily Tighten


Engage the hook and temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 3 bolts in the order shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 3.REMOVE ENGINE STAND

a.

Using a chain block and sling device, secure the engine assembly.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.

Remove the engine stand from the engine.


Hide 13405 4.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Using height adjustable attachments or plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustable attachments or plate lift attachments, place the engine assembly horizontally.

·

Using an engine sling device and engine lifter, secure the engine assembly before servicing.




b.
A305670E01
2.146,1.99 2.385,1.75 true 2.458,1.677 2.844,1.844 0.385,0.167 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


c.

Install the flywheel sub-assembly to the crankshaft.


d.

Clean the 8 bolts and their holes.


e.
A192239C41
1.781,0.552 1.542,1.385 false 1.833,0.458 2.01,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
A312678E01
1.667,0.375 1.802,0.552 0.135,0.177 10 true 1 1.635,1.49 1.771,1.667 0.135,0.177 10 true 2 1.073,0.917 1.208,1.094 0.135,0.177 10 true 3 2.177,0.927 2.313,1.104 0.135,0.177 10 true 4 1.208,0.51 1.344,0.688 0.135,0.177 10 true 5 2.031,1.365 2.167,1.542 0.135,0.177 10 true 6 1.198,1.344 1.333,1.521 0.135,0.177 10 true 7 2.042,0.521 2.177,0.698 0.135,0.177 10 true 8

Install and uniformly tighten the 8 bolts in several steps, in the sequence shown in the illustration.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31250 5.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 6.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 7.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 30300 8.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C294383C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



b.
A314469C01
0.917,0.333 1.208,0.333 true 2.573,1.021 2.74,1.021 true 0.76,0.26 1.073,0.417 0.313,0.156 10 false *1 2.792,0.958 3.104,1.115 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.

Align the input shaft with the clutch disc assembly and install the manual transaxle assembly to the engine assembly.

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly.

·

When mounting the manual transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

When tightening the bolts, be sure that the contact surfaces of the engine assembly and manual transaxle assembly are in close contact with one another.




d.
A314456E01
1.448,0.031 1.604,0.229 0.156,0.198 10 false A 2.823,0.073 2.979,0.271 0.156,0.198 10 false A 3.125,0.813 3.281,1.01 0.156,0.198 10 false B 3.167,1.26 3.323,1.458 0.156,0.198 10 false A 2.594,1.948 2.75,2.146 0.156,0.198 10 false C 2.823,1.792 2.979,1.99 0.156,0.198 10 false C 1.719,1.979 1.875,2.177 0.156,0.198 10 false C 1.25,1.896 1.406,2.094 0.156,0.198 10 true C

Install the manual transaxle assembly to the engine assembly with the 8 bolts.

Torque:
Bolt A and B : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt C : 39 N*m (398 kgf*cm, 29 ft.*lbf)

Bolt Length:
Item Length
Bolt A 45 mm (1.77 in.)
Bolt B 80 mm (3.15 in.)
Bolt C 35 mm (1.38 in.)



Hide 82121 9.INSTALL ENGINE WIRE

a.

Connect all the engine wire connectors.


b.

Connect the engine wire to the manual transaxle assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


c.

Connect the engine wire to the cylinder head cover sub-assembly with the 2 nuts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


d.

Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 51201 10.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Temporarily tighten the front suspension crossmember sub-assembly to the engine moving control rod bracket with the through bolt.


Hide 11.REMOVE ENGINE HANGER

a.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly.


Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 13.INSTALL STARTER ASSEMBLY

Hide 14.INSTALL ENGINE ASSEMBLY WITH MANUAL TRANSAXLE ASSEMBLY

a.

Place height adjustment or plate lift attachments on an engine lifter, and then set the engine assembly with manual transaxle assembly.

NOTICE:
·

Place the height adjustment or plate lift attachments so that the engine assembly with manual transaxle assembly is level.

·

As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.




b.

Operate the engine lifter and lift the engine assembly with transaxle and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the engine is clear of all wiring and hoses.



c.

Connect the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Tighten by holding the nut and turning the bolt.



d.

Connect the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the bolt and 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


e.

Temporarily install the front suspension crossmember sub-assembly to the body with the 6 bolts.


f.

By inserting SST into the datum holes in the front suspension crossmember RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

C233133C02
4.458,1.5 4.573,1.302 true 4.094,2.635 4.719,2.635 true 2.781,1.5 2.698,1.292 true 3.135,2.635 2.51,2.635 true 4.313,1.479 4.469,1.625 0.156,0.146 10 false *a 2.802,1.479 2.958,1.625 0.156,0.146 10 false *a 5.563,2.052 5.688,2.198 0.125,0.146 10 false A 5.333,2.458 5.458,2.604 0.125,0.146 10 false B 5.365,2.656 5.49,2.802 0.125,0.146 10 false C 1.51,1.979 1.635,2.125 0.125,0.146 10 false A 1.771,2.427 1.896,2.573 0.125,0.146 10 false B 3.802,2.573 4.104,2.719 0.302,0.146 10 false SST 3.156,2.573 3.458,2.719 0.302,0.146 10 false SST 5.76,3.521 5.99,3.667 0.229,0.146 10 false *c 5.021,3.521 5.25,3.667 0.229,0.146 10 false *b 2.469,3.521 2.698,3.667 0.229,0.146 10 false *c 1.729,3.521 1.958,3.667 0.229,0.146 10 false *b 1.771,2.635 1.896,2.781 0.125,0.146 10 false C
*a Datum Hole *b Correct
*c Incorrect - -
V100135

Front of Vehicle - -


SST
09670-00011  

Torque:
Bolt A : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Bolt B : 165 N*m (1683 kgf*cm, 122 ft.*lbf)
Bolt C : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole vertically.

·

If impossible to insert SST vertically, loosen all bolts and then insert SST again.




g.

Tighten the engine moving control rod bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 51108A 15.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH (w/ Side Rail Reinforcement)

Hide 51107A 16.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH (w/ Side Rail Reinforcement)

HINT:

Use the same procedure described for the LH side.


Hide 12144 17.INSTALL OIL PAN COVER SILENCER (w/ Metal Type Under Cover)

HINT:

Perform this procedure only when replacement of the oil pan cover silencer is necessary.


a.
A380371C01
2.198,1.177 2.583,1.333 false 2.646,1.271 2.958,1.469 0.313,0.198 10 false *a
*a Align RH Edge


Align the RH edge of the oil pan cover silencer with the oil pan protector and attach it as shown in the illustration.


Hide 12137 18.INSTALL OIL PAN PROTECTOR (w/ Metal Type Under Cover)

a.

Install the oil pan protector to the oil pan sub-assembly with the 3 bolts.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


Hide 43498A 19.INSTALL NO. 1 DRIVE SHAFT HEAT INSULATOR

A381267C01
0.729,1.594 0.906,1.729 0.177,0.135 10 true 1 2.177,1.396 2.354,1.563 0.177,0.167 10 true 2

a.

Temporarily tighten the No. 1 drive shaft heat insulator to the oil pan sub-assembly with the 2 bolts.


b.

Fully tighten the 2 bolts, in the sequence shown in the illustration.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


Hide 45025D 20.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45209 21.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 22.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33820B 24.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 17410 25.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 26.INSTALL FRONT FLOOR CENTER BRACE

Hide 82121 27.CONNECT ENGINE WIRE (for LHD)

a.
A313900C02
3.052,0.948 3.323,1.146 0.271,0.198 10 false 45° 2.417,0.958 2.688,1.156 0.271,0.198 10 false 45° 2.75,0.917 3.063,1.115 0.313,0.198 10 false *a
*a Top of the Vehicle


Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.


b.

Engage the clamp to connect the engine wire to the wire harness clamp bracket.


c.

Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.


d.

Connect the 3 connectors.


e.

Engage the 2 claws to connect the engine wire to the engine room relay block.


f.

Install the nut to the engine room relay block.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Connect the connector to the engine room relay block.


h.

Engage the clamp to connect the engine wire to the vehicle.


i.

Connect the engine wire to the vehicle with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


j.

Install the relay block cover to the engine room relay block.


Hide 82121 28.CONNECT ENGINE WIRE (for RHD)

a.
A112923C01
0.51,0.146 0.823,0.302 0.313,0.156 10 false *a 0.781,0.198 1.031,0.385 0.25,0.188 10 false 45° 0.25,0.198 0.5,0.385 0.25,0.188 10 false 45°
*a Top of the Vehicle


Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.


b.
A382560

Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.


c.

Connect the 3 connectors as shown in the illustration.


d.

Engage the 2 claws to connect the engine wire to the engine room relay block.


e.

Install the nut to the engine room relay block.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


f.

Connect the connector to the engine room relay block.


g.

Engage the clamp to connect the engine wire to the vehicle.


h.

Connect the engine wire to the vehicle with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


i.

Install the relay block cover to the engine room relay block.


Hide 55550 29.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 88320 31.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Cooler System)

a.
A381266C01
0.906,0.729 1.063,0.927 0.156,0.198 10 true 1 2.365,0.302 2.521,0.5 0.156,0.198 10 true 3 2.406,1.698 2.563,1.896 0.156,0.198 10 true 4 1.052,1.865 1.208,2.063 0.156,0.198 10 true 2

Install the cooler compressor assembly to the cylinder block sub-assembly and oil pan sub-assembly with the 4 bolts, in the sequence shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Connect the cooler compressor assembly connector.


Hide 23901 32.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23841B 33.INSTALL EFI FUEL PIPE CLAMP

Hide 87245 34.CONNECT INLET HEATER WATER HOSE

a.
A313898C01
1.729,0.427 1.844,0.594 false 1.052,0.115 1.365,0.271 0.313,0.156 10 false *a 1.594,0.302 1.906,0.458 0.313,0.156 10 false *b 1.781,0.104 2.094,0.26 0.313,0.156 10 false *c 1.167,0.74 1.479,0.896 0.313,0.156 10 false *d 1.021,2.875 1.177,3.073 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Front of Vehicle


Engage the clamp to connect the hose clamp to the wire harness clamp bracket.


b.

Connect the inlet heater water hose to the cylinder head sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the inlet heater water hose and hose clip at the correct angle.



Hide 87246 35.CONNECT OUTLET HEATER WATER HOSE

a.
A313896C01
1.958,0.583 1.802,0.427 false 1.146,0.125 1.458,0.281 0.313,0.156 10 false *a 1.604,0.333 1.917,0.49 0.313,0.156 10 false *b 1.906,0.115 2.219,0.271 0.313,0.156 10 false *c 1.302,0.74 1.615,0.896 0.313,0.156 10 false *d 1.271,2.583 1.427,2.781 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Front of Vehicle


Connect the outlet heater water hose to the No. 1 water by-pass pipe and slide the hose clip to secure it.

NOTICE:

Perform the installation with the outlet heater water hose and hose clip at the correct angle.



Hide 16572D 36.CONNECT NO. 2 RADIATOR HOSE

a.
A382168C01
1.51,2.26 1.646,2.49 true 1.031,2.125 1.344,2.281 0.313,0.156 10 false *a 1.354,2.188 1.667,2.344 0.313,0.156 10 false *b 1.573,2.083 1.885,2.24 0.313,0.156 10 false *c 2.323,1.427 2.479,1.625 0.156,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle


Connect the No. 2 radiator hose to the water inlet and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 2 radiator hose and hose clip at the correct angle.



Hide 16571C 37.CONNECT NO. 1 RADIATOR HOSE

a.
A383011C01
0.708,0.385 0.979,0.51 false 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.531,0.292 0.844,0.448 0.313,0.156 10 false *b 0.875,0.115 1.188,0.271 0.313,0.156 10 false *c 2.354,2.167 2.51,2.365 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle


Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 1 radiator hose and hose clip at the correct angle.



b.

Engage the clamp to connect the No. 1 radiator hose to the hose clamp.


Hide 44774 38.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the intake manifold and slide the hose clip to secure it.


Hide 27020 39.INSTALL GENERATOR WITH REGULATOR ASSEMBLY

Hide 40.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 17167 42.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 43.INSTALL OIL LEVEL DIPSTICK GUIDE

Hide 15301 44.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 16361A 45.INSTALL FAN AND GENERATOR V BELT

Hide 74410 46.INSTALL BATTERY CARRIER ASSEMBLY

a.

Install the battery carrier assembly to the engine mounting insulator LH and vehicle with the 5 bolts.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


b.

Engage the 4 clamps to connect the wire harness to the battery carrier assembly.


Hide 74431 47.INSTALL BATTERY TRAY

a.

Install the battery tray to the battery carrier assembly.


Hide 28800 48.INSTALL BATTERY

a.
A314466C02
0.406,0.177 0.531,0.292 true 0.698,0.438 0.844,0.219 true 0.917,1.365 1.021,1.417 false 0.74,1.49 0.865,1.646 true 1.063,1.354 1.375,1.51 0.313,0.156 10 false *1 0.885,1.625 1.083,1.792 0.198,0.167 10 true *2 0.25,0.083 0.563,0.24 0.313,0.156 10 false *3 0.865,0.156 1.073,0.313 0.208,0.156 10 false *4
*1 Battery Clamp Bolt
*2 Battery Carrier
*3 Engine Room Main Wire
*4 Engine Wire


Install the battery to the battery tray.


b.

Install the battery clamp sub-assembly to the battery carrier assembly with the 2 nuts and battery clamp bolt.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

HINT:

Engage the hook of the battery clamp bolt to the notch of the battery carrier.



c.

Engage the 2 claws to connect the engine room main wire to the engine wire.


d.

Connect the engine room main wire with engine wire to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


e.

Install the terminal cover to the positive (+) battery terminal.


Hide 17701 49.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the air cleaner bracket with the 3 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the clamp to install the engine wire to the air cleaner case sub-assembly.


Hide 17801 50.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 51.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


b.

Engage the 2 clamps of the air cleaner cap sub-assembly.


c.

Engage the 2 clamps to install the engine wire to the air cleaner cap sub-assembly.


d.

Connect the mass air flow meter connector.


Hide 17880 52.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 12262 53.CONNECT NO. 2 VENTILATION HOSE

Hide 23827A 54.CONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A381828C01
2.052,0.823 2.313,0.708 false 1.438,0.99 1.594,1.188 0.156,0.198 10 false A 1.875,0.792 2.188,0.99 0.313,0.198 10 false *b 1.927,0.198 2.24,0.396 0.313,0.198 10 false *a 2.135,0.385 2.469,0.573 0.333,0.188 10 false 30° 2.438,0.385 2.75,0.594 0.313,0.208 10 false 30° 2.406,0.167 2.719,0.365 0.313,0.198 10 false *c
*a View A
*b Hose Paint Mark
*c Top of Vehicle


Connect the No. 2 fuel vapor feed hose to the purge VSV (purge valve).

NOTICE:

Perform the installation with the No. 2 fuel vapor feed hose at the correct angle.



Hide 23826 55.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A384682C03
2.406,1.396 2.479,1.094 false 0.552,1.25 0.708,1.448 0.156,0.198 10 false A 1.854,0.458 2.073,0.625 0.219,0.167 10 false *a 2.292,1.417 2.531,1.594 0.24,0.177 10 false *b 2.823,0.958 3.042,1.125 0.219,0.167 10 false *c 2.208,0.344 2.427,0.51 0.219,0.167 10 false *d 2.615,0.833 2.885,1.01 0.271,0.177 10 false 30° 2.615,1.094 2.917,1.271 0.302,0.177 10 false 30°
*a View A
*b Hose Paint Mark
*c Rear Side of Vehicle
*d Top of Vehicle


Connect the No. 1 fuel vapor feed hose to the purge VSV (purge valve) and slide the hose clip to secure it.

NOTICE:

Perform the installation with the No. 1 fuel vapor feed hose at the correct angle.



Hide 56.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 57.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65.INSPECT RESERVOIR TANK COOLANT LEVEL

Hide 66.INSPECT FOR MANUAL TRANSAXLE OIL LEAK

Hide 67.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 71.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441C 72.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

w/o Side Rail Reinforcement:

i.

Install the engine under cover RH to the vehicle with the 2 bolts and 2 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Side Rail Reinforcement:

i.

Install the engine under cover RH to the vehicle with the 3 clips.


ii.

Install the bolt and 2 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51442C 73.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

a.

w/o Side Rail Reinforcement:

i.

Install the engine under cover LH to the vehicle with the 3 bolts and 5 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



b.

w/ Side Rail Reinforcement:

i.

Install the engine under cover LH to the vehicle with the 3 clips.


ii.

Install the 3 bolts and 4 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)



Hide 51405A 74.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

a.

Install the No. 1 engine under cover sub-assembly to the vehicle with the 11 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 51451A 75.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

a.

Install the center engine under cover to the vehicle with the 4 screws and 5 clips.