Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2020.07–2021.11
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424635 CYLINDER HEAD GASKET A

M15A-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Perform "Reset Memory"

2.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for TMC Made:
(Click here)
for TMMF Made:
(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking support brake system (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 89481B 4.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)

Hide 25733A 5.REMOVE NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)

Hide 17167 6.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 9.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 10.REMOVE THROTTLE BODY GASKET

Hide 23250 11.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11452D 14.REMOVE OIL LEVEL GAGE GUIDE

Hide 15.REMOVE NO. 1 WATER BY-PASS PIPE ASSEMBLY

Hide 16281 16.REMOVE NO. 4 WATER BY-PASS HOSE

Hide 12262 17.REMOVE NO. 2 VENTILATION HOSE

Hide 18.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 11102A 19.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 20.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 21.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 22.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 23.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 13470 24.REMOVE CRANKSHAFT PULLEY ASSEMBLY

Hide 11201 25.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 26.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 27.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11320B 28.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11301C 29.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 31.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13540 34.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 35.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 36.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13070A 37.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11310 38.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13478 39.REMOVE CRANKSHAFT PULLEY SPACER

Hide 11103 40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13501A 42.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

Hide 13502B 43.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

Hide 11101 44.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 45.REMOVE CYLINDER HEAD GASKET

A466044

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 46.INSPECT CYLINDER HEAD SET BOLT

Hide 11101 47.INSPECT CYLINDER HEAD SUB-ASSEMBLY