Home › Engine / Hybrid System · 1NZ-FE › ENGINE CONTROL › 1NZ-FE SFI SYSTEM

DTC    P1604    Startability Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when there is engine starting trouble due to running out of fuel.

DTC No.
DTC Detection Condition
Trouble Area
P1604
Either condition is met. (1 trip detection logic):
  1. The engine speed is below 500 rpm with the STA signal on for a certain amount of time (refer to the illustration below).*1
  2. After the engine starts (engine speed is 500 rpm or more), the engine speed drops to 200 rpm or less within approximately 2 seconds.*2
  1. Immobiliser system*3
  2. Engine assembly (excess friction, compression loss)
  3. Starter assembly
  4. Crankshaft position sensor
  5. Camshaft position sensor
  6. Engine coolant temperature sensor
  7. Fuel pump
  8. Fuel pump control circuit
  9. Fuel line (fuel filter, pipes and hoses)
  10. Fuel injector assembly
  11. Throttle with motor body assembly
  12. Fuel pressure regulator
  13. Battery
  14. Drive plate and ring gear sub-assembly*4
  15. Flywheel sub-assembly*5
  16. Spark plug
  17. Ignition coil circuit
  18. Intake system
  19. Camshaft timing oil control valve assembly
  20. Mass air flow meter
  21. Heated oxygen sensor
  22. Valve timing
  23. Fuel
  24. Purge VSV
  25. Intake valve
  26. ECM
*1: In case that the engine is difficult to start or that the engine does not start.
*2: In case that the engine speed drops or the engine stalls right after engine start.
*3: w/ Immobiliser System
*4: for Automatic Transaxle
*5: for Manual Transaxle

A220316E01


Reference waveforms showing a normal cold engine start

A259947


Reference waveforms showing a normal warm engine start

A258726


Reference values when there is an air leak in the air induction system during starting difficulty

Freeze Frame Data P1604 Startability Malfunction 
Engine and ECT
Current
P1604: Startability Malfunction
Time Freeze Frame Data
Item
Data1
Data2
Data3
Data4
Data5
Unit
Engine Speed
253
1382
582
196
157
rpm
Calculate Load
94.1
42.7
25.0
94.1
94.1
%
Vehicle Load
9.8
6.6
14.1
17.2
15.2
%
MAF
0.32
1.18
1.07
0.43
0.31
gm/sec
Atmosphere Pressure
103
103
103
103
103
kPa
Coolant Temp
89
89
89
89
89
°C
Intake Air
48
48
48
48
48
°C
Ambient Temperature
25
25
25
25
25
°C
Battery Voltage
10.351
12.421
12.578
12.285
12.226
V
Throttle Sensor Volt %
20.3
17.6
20.3
20.3
20.3
%
Throttle Sensor #2 Volt %
53.3
49.4
53.3
53.3
53.3
%
Throttle Sensor Position
1.5
0.0
1.5
1.5
1.5
%
Throttle Motor DUTY
20.3
17.6
20.3
20.3
20.3
%
Injector (Port)
8624
4102
2944
2545
2545
μs
Injection Volume (Cylinder 1)
0.153
0.153
0.133
0.133
0.133
ml
Fuel Pump/Speed Status
ON
ON
ON
ON
ON

EVAP (Purge) VSV
0.0
0.0
0.0
0.0
0.0
%
Evap Purge Flow
0.0
0.0
0.0
0.0
0.0
%
Purge Density Learn Value
0.000
0.000
0.000
0.000
0.000

EVAP purge VSV
OFF
OFF
OFF
OFF
OFF

Target Air-Fuel Ratio
1.186
1.167
1.136
1.110
1.186

O2S B1S1
0.015
0.015
0.015
0.015
0.015
V
O2S B1 S2
0.000
0.015
0.000
0.000
0.000
V
Short FT #1
0.000
0.000
0.000
0.000
0.000
%
Long FT #1
-5.469
-4.688
-5.469
-4.688
-5.469
%
Total FT #1
0.000
0.000
0.000
0.000
0.000

Fuel System Status #1
Unused
OL
OL
Unused
Unused

IGN Advance
5.0
5.0
13.0
11.5
11.5
deg
Knock Feedback Value
-1.5
-1.5
-1.5
-1.5
-1.5
°CA
Knock Correct Learn Value
10.2
10.2
10.2
10.2
10.2
°CA
VVT Control Status #1
OFF
OFF
OFF
OFF
OFF

Starter Signal
ON
OFF
OFF
OFF
OFF


WIRING DIAGRAM

Refer to P0100 for the mass air flow meter circuit .
Refer to P0115 for the engine coolant temperature sensor circuit .
Refer to P0335 for the crankshaft position sensor .
Refer to P0340 for the camshaft position sensor .
Refer to P0351 for the ignition coil circuit .
Refer to P0443 for the purge VSV circuit .
Refer to Fuel Pump Control Circuit .
Refer to Fuel Injector Circuit .
Refer to Starter Signal Circuit .

INSPECTION PROCEDURE

HINT:
  1. In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1604 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as starting difficulty.
    As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.
  2. If any other DTCs are output, perform troubleshooting for those DTCs first.
  3. When the Data List item "Immobiliser Fuel Cut" is ON, the engine cannot be started.
  4. Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
  5. When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (Click here).
  6. When confirming the freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
  7. Try to start the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and compare it with the freeze frame data.
  8. If the malfunction does not reoccur, carefully check the vehicle conditions from when the malfunction occurred using freeze frame data.
  9. When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
  10. If the same inspection or replacement procedure appears 2 times when performing an inspection procedure, it is not necessary to repeat the procedure the second time.


Malfunction Recurrence and Inspection Areas
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    1. The engine speed recorded in the freeze frame data is 0 rpm (the engine does not crank).

      HINT:
      One of the following problems may be present: battery depletion, excess engine friction, a starter malfunction or a crankshaft position sensor malfunction.

      1. If the battery voltage is less than 6 V during cranking, there is a high probability that engine friction is abnormal.
      2. If the battery voltage drops to 5 V or less when starting the engine, the battery may be malfunctioning.

      3. If the battery voltage fluctuates while cranking the engine, it can be concluded that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor and/or an ECM may be malfunctioning.


        A215383E32

    2. All engine speeds recorded in the freeze frame data are between 60 and 250 rpm (the engine cranks but there is no combustion).

      HINT:
      If the engine speed is between 60 and 250 rpm (no initial combustion), there may be a wiring problem or a complete failure of an ignition or fuel system part.


      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and the engine may not be able to be started.


        A215384E14

    3. The engine speed recorded in the freeze frame data is 250 rpm or higher (the initial combustion and starter turnoff timing is too late).

      HINT:
      If the engine speed is 250 rpm or higher (combustion occurs but the initial combustion and starter turnoff timing is too late), the fuel injection volume is often incorrect (too low or too high) and determining the cause of the malfunction is often difficult.

      1. Due to an engine coolant temperature sensor malfunction, the fuel injection volume is extremely high or low and engine starting trouble may occur.
      2. If Long FT #1 is incorrect, there may be a fuel supply problem due to the injectors or fuel pump being clogged, etc.

      3. If the engine cranking speed is too high, compression loss may have occurred due to carbon interfering with the valve operation.


        A215383E48

  2. When the malfunction (starting difficulty) can be reproduced, or malfunction conditions are known, perform the following inspections ("Problem symptoms" and "Systems to inspect")

    1. Problem symptoms

      1. The engine does not crank.

        HINT:
        The starter is normal if a noise that indicates the starter pinion gear is extending is heard. The battery may be fully depleted or there may be excess engine friction.

      2. The engine cranking speed is abnormal.

        HINT:
        If the engine cranking speed is too high (for example, 300 rpm or higher with no combustion), compression loss may have occurred because carbon interfered with valve operation, etc.

      3. There is no initial combustion.

        HINT:
        If there is no initial combustion, there is probably a wiring problem or an ignition or fuel system part malfunction.

      4. The engine stalls after starter turnoff.

        HINT:
        If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the VVT may have a problem returning.

      5. The initial combustion and starter turnoff occur late.

        HINT:
        If the initial combustion and starter turnoff occur late, the fuel injection volume is probably incorrect (too low or too high).

        HINT:
        Causes of fuel system malfunctions according to conditions present at the time of the malfunction.
        1. When 2 to 3 minutes have elapsed after stopping the engine: Fuel pressure loss due to the pressure regulator failing to maintain the fuel pressure.
        2. When 15 to 120 minutes have elapsed after stopping the engine: Problem with injector fuel seal.
        3. When a long time has elapsed after stopping the engine: Pressure regulator is stuck open.

    2. Systems to inspect.

      1. Intake system
      2. Ignition system
      3. Fuel system


INSPECTION FLOW
  1. Freeze frame data exists, but the malfunction (starting difficulty) has not reoccurred and the malfunction conditions are unknown.

    Freeze Frame Data Item
    Result
    Suspected Area
    Procedure
    Engine Speed
    0 rpm (no engine cranking at all)
    1. Battery fully depleted
    2. Engine assembly (excess friction)
    3. Starter assembly
    4. Crankshaft position sensor
    5. ECM
    4 to 9
    60 to 250 rpm (engine cranks but no initial combustion*1)
    1. Fuel pump control circuit
    2. Ignition system
    3. Immobiliser system*3
    4. Engine coolant temperature sensor
    5. Fuel injection system
    10 to 14
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff*2 occur late)
    1. Engine assembly (compression loss)
    2. Fuel injection system
    3. Fuel pump control circuit
    15 to 23
    *3: w/ Immobiliser System

    HINT:
    1. *1: First combustion after cranking begins.
    2. *2: Condition when engine speed increases and starter can be turned off.

  2. When the malfunction (starting difficulty) can be reproduced, or when malfunction conditions are known.

    1. Problem symptoms

      Problem Symptom
      Suspected Area
      Suspected Component
      Procedure
      The engine does not crank
      Battery malfunction
      1. Battery fully depleted
      26 to 31
      Starting system
      1. Starter assembly (includes pinion gear wear or tooth damage)
      2. Starting system
      Engine assembly
      1. Engine assembly (excess friction)
      2. Drive plate wear or tooth damage*1
      3. Flywheel wear or tooth damage*2
      Cranking speed too low
      Battery malfunction
      1. Battery fully depleted
      32 to 34
      Starting system
      1. Starter assembly
      Engine assembly
      1. Engine assembly (excess friction)
      Cranking speed too high
      Engine assembly
      1. Engine assembly (compression loss)
      There is no initial combustion
      Fuel supply problem
      1. Cannot maintain pressure due to pressure regulator malfunction
      2. Fuel injector leak
      3. Fuel leak from fuel line
      4. Fuel pump control circuit
      5. Fuel pump
      35 to 48
      Immobiliser system
      1. Immobiliser system*3
      Ignition system malfunction
      1. Spark plug
      2. Crankshaft position sensor
      3. Ignition coil No. 1
      Engine stalls after starter turnoff
      Air suction
      1. Intake system connections
      49 to 54
      Deposits in throttle body
      1. Throttle with motor body assembly
      VVT valve does not return properly
      1. Camshaft timing oil control valve assembly
      Mass air flow meter malfunction
      1. Mass air flow meter
      The initial combustion and starter turnoff occur late
      Engine coolant temperature sensor malfunction
      1. Engine coolant temperature sensor
      55 to 68
      Mass air flow meter malfunction
      1. Mass air flow meter
      Abnormal A/F learning value
      1. Heated oxygen sensor
      Deviation from fuel injection characteristics
      1. Fuel injector assembly
      Wet-fouled or dry-fouled spark plug
      1. Spark plug
      Lack of fuel pressure
      1. Pressure regulator
      2. Fuel pump
      3. Fuel pump control circuit
      *1: for Automatic Transaxle
      *2: for Manual Transaxle
      *3: w/ Immobiliser System

    2. Systems to inspect.

      Troubleshooting by System
      Suspected Area
      Suspected Component
      Procedure
      Fuel system troubleshooting A
      Abnormal air-fuel ratio learning value
      1. Fuel injector assembly
      83 to 90
      91 to 98
      Rough idling
      1. Crankshaft position sensor
      Abnormal fuel pressure
      1. Fuel
      2. Fuel leak from fuel line
      3. Fuel pump
      4. Pressure regulator
      Fuel system troubleshooting B
      Abnormal concentration of HC in surge tank
      1. Purge VSV system
      2. Fuel injector assembly
      99 to 101
      Fuel system troubleshooting C
      Injection signal system malfunction
      1. Fuel injector assembly
      2. Crankshaft position sensor
      3. Camshaft position sensor
      4. ECM
      70 to 73
      Intake system troubleshooting
      Difference between ISC target value and opening angle when idling
      1. Engine assembly (compression loss)
      2. Valve timing
      3. Engine coolant temperature sensor
      4. ECM
      80 to 82
      102 to 104
      Ignition system troubleshooting
      Camshaft and/or crankshaft position sensor signal malfunction
      1. Crankshaft position sensor system (including sensor installation)
      2. Camshaft position sensor system (including sensor installation)
      3. ECM
      74 to 79
      105 to 110

NOTICE:
  1. Inspect the fuses circuit related to this system before performing the following inspection procedure
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK ANY OTHER DTCS OUTPUT AND RECORD FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.



    A103809E46
  1. Read DTCs and record the Freeze Frame Data.

    HINT:
    1. This freeze frame data shows the actual engine conditions when engine starting trouble occurred.
    2. When confirming the freeze frame data, be sure to check all 5 data sets of freeze frame data.
    3. The fourth set of freeze frame data is the data recorded when then the DTC is stored.

    Result 
    Result
    Proceed to
    DTC P1604 is output
    A
    DTC P1604 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK ENGINE IMMOBILISER SYSTEM

HINT:
If the vehicle is not equipped with a immobiliser system, proceed to next step (OK).

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Fuel Cut.

  1. Read the value displayed on the tester.

    OK:
    Immobiliser Fuel Cut is OFF

    HINT:
    If the engine is cranked immediately after reconnecting the battery cable (key verification for immobiliser system not completed), the engine cannot be started. Key verification needs to wait for several seconds after turning the ignition switch to ON.



NG
REPAIR ENGINE IMMOBILISER SYSTEM (Click here)
OK


3.CHECK MALFUNCTION CONDITION
  1. Confirm the problem symptoms.

    Result 
    Result
    Proceed to
    Freeze frame data exists, but the starting difficulty cannot be reproduced and it is unknown what kind of starting difficulty occurred
    A
    The problem symptoms can be reproduced, or the malfunction conditions are known
    B



B
Go to step 25
A


4.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Engine Speed
    Battery Voltage
    All 5 sets of freeze frame data are 0 rpm (no engine cranking at all)
    Minimum voltage is less than 5 V
    Battery fully depleted
    A
    Minimum voltage is 5 V or higher
    1. Starter malfunction
    2. Crankshaft position sensor system
    3. Excess engine friction
    4. ECM
    B
    60 to 250 rpm (engine cranks but no initial combustion)
    -
    1. Fuel pump control circuit
    2. Ignition system
    3. Engine coolant temperature sensor
    4. Fuel injection system
    C
    250 rpm or higher (combustion occurs but initial combustion and starter turnoff occur late)
    -
    1. Engine assembly
    2. Engine coolant temperature sensor
    3. Fuel injection system
    4. Fuel pump control circuit
    D

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Low Rev for Eng Start
    ON exists
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter
    E

    HINT:
    When DTC P1604 is stored, either "Engine Start Hesitation"*1 or "Low Rev for Eng Start"*2 in the Freeze Frame Data will be ON. If "Low Rev for Eng Start" is ON, proceed to E.
    *1: This value turns ON when the engine speed does not reach a certain value for a certain period of time when starting the engine.
    *2: This value turns ON when the engine stalls immediately after starting the engine. If "Low Rev for Eng Start" is ON, as there is a possibility that the low engine speed or engine stall was caused by the user, confirm the following freeze frame data items.
    1. Immobiliser Fuel Cut
    2. Engine Speed (Starter Off)
    3. Shift SW Status (R, D Range) (for Automatic Transaxle)



B
Go to step 5

C
Go to step 10

D
Go to step 15

E
Go to step 49
A

CHARGE OR REPLACE BATTERY 

5.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Battery Voltage
    Minimum voltage is 6 V or higher and voltage does not fluctuate*1
    Starter system
    A
    Minimum voltage is 6 V or higher and voltage fluctuates*2, *3
    1. Crankshaft position sensor system
    2. ECM
    B
    Minimum voltage is 5 to 6 V*4
    1. Excess engine friction
    2. Battery fully depleted
    C

    HINT:

    1. A217930E01
      *1: The 5 sets of freeze frame data show approximately the same battery voltage.
    2. *2: The 5 sets of freeze frame data show different battery voltages.
    3. *3: If the voltage fluctuates, it can be determined that cranking is being performed. When the engine speed is 0 rpm, the crankshaft position sensor system and/or the ECM may be malfunctioning.
    4. *4: There may be excess engine friction. Make sure that the crankshaft rotates smoothly when turning it by hand. Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



B
Go to step 6

C
CHECK AND REPAIR ENGINE ASSEMBLY OR BATTERY
A

CHECK STARTER SIGNAL CIRCUIT (Click here)  

6.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


7.INSPECT CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.

  1. Check for oil on the connector terminals.

    OK:
    No oil on the terminals.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

10.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temperature, Intake Air
    Coolant Temp, Ambient Temperature
    Fuel Pump/Speed Status
    Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C (18°F) or more*1
    Coolant Temp is 125°C (257°F) or more, or lower than Ambient Temperature by 15°C (27°F) or more
    -
    Engine coolant temperature sensor
    A
    Other than above
    All 5 sets of freeze frame data are ON
    -
    B
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control circuit
    C
    Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C (18°F) *2
    -
    At least 1 of the 5 sets of freeze frame data is OFF
    Fuel pump control circuit
    C
    All 5 sets of freeze frame data are ON
    -
    B

    HINT:
    1. *1: A long time had not elapsed after stopping the engine.
    2. *2: A long time had elapsed after stopping the engine.



B
Go to step 11

C
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Disconnect the fuel pump connector.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.



    A190138E32
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K17-4 - Body ground
    Active Test is being performed
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pump)

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR)
  1. Check the harnesses and connectors, referring to DTC P0300 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR CIRCUIT (Click here)
OK


13.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 14
A

REPAIR OR REPLACE FUEL LINE 

14.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

15.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Suspected Area
    Proceed to
    Coolant Temp, Ambient Temperature, Intake Air
    Coolant Temp, Ambient Temperature
    Long FT #1
    Engine Speed
    Difference between Coolant Temp, Ambient Temperature and Intake Air is 10°C (18°F) or more
    Coolant Temp is 125°C (257°F) or more, or lower than Ambient Temperature by 15°C (27°F) or more
    -
    -
    Engine coolant temperature sensor
    A
    Other than above
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D
    Difference between Coolant Temp, Ambient Temperature and Intake Air is less than 10°C (18°F)
    -
    -15% or less, or +15% or more
    -
    1. Fuel pump control circuit
    2. Fuel injector assembly
    B
    -15 to +15%
    Minimum speed is 300 rpm or more*1
    Engine assembly
    C
    Minimum speed is below 300 rpm
    1. Fuel system
    2. Intake air system
    D

    HINT:
    *1: Compression loss may have occurred in the engine assembly.



B
Go to step 16

C
CHECK AND REPAIR ENGINE ASSEMBLY

D
Go to step 18
A

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

16.INSPECT FUEL INJECTOR ASSEMBLY
  1. Check that no carbon is stuck to the fuel injector assembly.

    OK:
    No carbon present.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


17.CHECK FUEL SYSTEM
  1. Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

    Result 
    Result
    Proceed to
    There is foreign matter or signs that fuel pump was stuck
    A
    There is no foreign matter and no signs that fuel pump was stuck
    B

    HINT:
    If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.



B
Go to step 24
A

REPAIR OR REPLACE FUEL SYSTEM 

18.READ FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON end turn the tester on.

  1. Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

    Result 
    Freeze Frame Data Item
    Result
    Suspected Area
    Proceed to
    Coolant Temp
    Engine coolant temperature is 40°C (104°F) or less*1
    Pressure regulator
    A
    Engine coolant temperature is 40 to 90°C (104 to 194°F)*2
    Fuel injector assembly
    B
    Engine coolant temperature is 90°C (194°F) or more*3
    Pressure regulator
    A

    HINT:
    *1: If the engine coolant temperature is 40°C [104°F] or less (after stopping the engine and the vehicle is not driven for a long period of time), the pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: If the engine coolant temperature is 40 to 90°C [104 to 194°F] (15 to 120 minutes have passed after stopping the engine), there may be fuel leaking from a fuel injector assembly.
    *3: If the engine coolant temperature is 90°C [194°F] or more (2 to 5 minutes have passed after stopping the engine), there may be a problem with the pressure regulator failing to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.



B
Go to step 20
A


19.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.


    Result 
    Result
    Proceed to
    Abnormal
    A
    Normal
    B



B
Go to step 24
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

20.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.



B
Go to step 22
A


21.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).

    Result 
    Result
    Proceed to
    Normal
    A
    Abnormal
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


22.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    Result 
    Result
    Proceed to
    No carbon present
    A
    Carbon in passage
    B



B
CLEAN OR REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
A


23.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leak (Click here).

    OK:
    No leak in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


24.PERFORM SIMULATION TEST
  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine cannot be started
    A
    Engine can be started
    B



B
END
A


25.CONFIRM PROBLEM SYMPTOM
  1. Confirm the problem symptoms.

    HINT:
    The problem symptoms below can be determined by reading the freeze frame data.


    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    The engine does not crank
    1. Battery fully depleted
    2. Starter (includes pinion gear wear or tooth damage)
    3. Starter system
    4. Engine assembly (excess friction)
    5. Drive plate wear or tooth damage*1
    6. Flywheel wear or tooth damage*2
    A
    Abnormal cranking speed
    1. Battery fully depleted
    2. Starter assembly
    3. Engine assembly (excess friction, compression loss)
    B
    There is no initial combustion (combustion does not occur even once)*3
    1. Pressure regulator fuel pressure maintenance
    2. Fuel injector leak
    3. Fuel leak from fuel line
    4. Fuel pump control circuit
    5. Fuel pump
    6. Spark plug
    7. Crankshaft position sensor system
    8. Ignition coil system
    C
    The engine stalls after starter turnoff (engine stalls immediately after the first time the engine speed increases)*4
    1. Intake system connections
    2. Throttle with motor body assembly
    3. Camshaft timing oil control valve assembly
    4. Mass air flow meter system
    D
    The initial combustion and starter turnoff occur late*5
    1. Engine coolant temperature sensor
    2. Mass air flow meter
    3. Heated oxygen sensor (sensor 1)
    4. Fuel injector assembly
    5. Spark plug
    6. Pressure regulator
    7. Fuel pump
    8. Fuel pump control circuit
    E
    *1: for Automatic Transaxle
    *2: for Manual Transaxle

    HINT:
    1. If there is hesitation (cranking speed is slow and combustion occurs before passing TDC) during the initial cranking period, the battery charge may be insufficient or the starter assembly may be malfunctioning.
    2. *3: If there is no initial combustion, a wire harness may be malfunctioning, or the ignition or fuel system may be malfunctioning.
    3. *4: If the engine stalls after starter turnoff, the air-fuel ratio may be incorrect or the camshaft timing oil control valve assembly may have a problem returning.
    4. *5: If the initial combustion and starter turnoff occur late, the fuel injection volume may be incorrect (too low or too high).



B
Go to step 32

C
Go to step 35

D
Go to step 49

E
Go to step 55
A


26.PERFORM SIMULATION TEST
  1. When cranking the engine, check for a noise indicating that the starter pinion gear is extending, and check that the starter pinion gear is not spinning freely.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    A noise indicating that the starter pinion gear is extending is heard and the starter pinion gear is not spinning freely.*3
    1. Battery
    2. Excess engine friction
    3. Starter assembly
    A
    A noise indicating that the starter pinion gear is extending is heard but the starter pinion gear is spinning freely.
    1. Drive plate*1
    2. Flywheel*2
    3. Starter assembly
    B
    A noise indicating that the starter pinion gear is extending is not heard
    1. Battery
    2. Starter assembly
    3. Starter system
    C
    *1: for Automatic Transaxle
    *2: for Manual Transaxle

    HINT:
    *3: The battery may be fully depleted or there may be excess engine friction.



B
Go to step 29

C
Go to step 30
A


27.INSPECT BATTERY
  1. Inspect the battery .



NG
CHARGE OR REPLACE BATTERY
OK


28.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



NG
REPAIR OR REPLACE ENGINE ASSEMBLY
OK

INSPECT STARTER ASSEMBLY 

29.INSPECT STARTER ASSEMBLY (STARTER PINION GEAR)
  1. Remove the starter (Click here).

  1. Check for starter pinion gear wear and damage.

    OK:
    There is no wear or damage.


    Result 
    Result
    Proceed to
    NG
    A
    OK (for automatic transaxle)
    B
    OK (for manual transaxle)
    C



B
REPLACE DRIVE PLATE AND GEAR SUB-ASSEMBLY

C
REPLACE FLYWHEEL SUB-ASSEMBLY
A

REPLACE STARTER ASSEMBLY 

30.INSPECT BATTERY
  1. Inspect the battery .



NG
CHARGE OR REPLACE BATTERY
OK


31.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here).



NG
REPLACE STARTER ASSEMBLY
OK

CHECK STARTER SIGNAL CIRCUIT (Click here)  

32.PERFORM SIMULATION TEST
  1. Check the cranking speed.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Cranking speed is slow (100 rpm or less)
    1. Battery
    2. Starter assembly
    3. Excess engine friction
    A
    Cranking speed is fast (300 rpm or more)*1
    Engine compression loss
    B

    HINT:
    *1: If the cranking speed is fast, there may be compression loss.



B
CHECK AND REPAIR ENGINE ASSEMBLY
A


33.INSPECT BATTERY
  1. Inspect the battery .



NG
CHARGE OR REPLACE BATTERY
OK


34.CHECK ENGINE ASSEMBLY
  1. Check that the crankshaft rotates smoothly when rotating it by hand.

    OK:
    Crankshaft rotates smoothly.

    HINT:
    Excess engine friction may have occurred temporarily. Remove the cylinder head cover and oil pan, and check for foreign matter such as iron fragments. If there is a malfunction or signs of a malfunction present, perform a detailed inspection by disassembling all the parts.



NG
CHECK AND REPAIR ENGINE ASSEMBLY
OK

INSPECT STARTER ASSEMBLY 

35.INSPECT FUEL INJECTOR ASSEMBLY
  1. Using a sound scope or screwdriver, check for an injector operating sound while cranking the engine.

    OK:
    Fuel injector operating sound is heard.



NG
Go to step 47
OK


36.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
Go to step 45
OK


37.CHECK SPARK PLUG AND SPARK
  1. Check for sparks .



NG
Go to step 41
OK


38.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 69, perform fuel system troubleshooting C (steps 70 to 73).



B
Go to step 40

C
Go to step 69
A


39.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, check the fuel pressure after cranking the engine.


    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    *1: From step 69, perform fuel system troubleshooting C (steps 70 to 73).



B
Go to step 69
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

40.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.
    2. *1: From step 69, perform fuel system troubleshooting C (steps 70 to 73).



B
Go to step 69
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

41.INSPECT SPARK PLUG
  1. Inspect the spark plugs .

HINT:
Even if the spark plug of only one cylinder is malfunctioning, replace the spark plugs of all cylinders.



NG
REPLACE SPARK PLUG
OK


42.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
CHECK CRANKSHAFT POSITION SENSOR CIRCUIT
OK


43.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)
  1. Check the harnesses and connectors, referring to DTC P0351 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK NO. 1 IGNITION COIL POWER SOURCE CIRCUIT
OK


44.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
  1. Check the harnesses and connectors, referring to DTC P0351 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness is normal, after replacing the No. 1 ignition coil, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform troubleshooting for the ignition system (steps 74 to 79).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NO.1 IGNITION COIL (Click here)  

45.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for an operating sound from the fuel pump.

    OK:

    Control the Fuel Pump/Speed
    Specified Condition
    ON
    Operating sound heard
    OFF
    Operating sound not heard

    HINT:
    Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


46.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform fuel system troubleshooting C (steps 70 to 73).



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

47.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. While running the engine, read the value of Engine Speed.

    OK:
    A value that matches the actual engine speed is constantly output.

    HINT:
    1. Check the engine speed using a line graph.
    2. If the engine cannot be started, check the engine speed while cranking the engine.
    3. If the engine speed is 0 rpm, the crankshaft position sensor may have an open or short circuit.



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


48.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)
  1. Check the harnesses and connectors, referring to DTC P0300 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR CIRCUIT
OK

REPLACE ECM (Click here)  

49.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
Go to step 54
OK


50.CHECK INTAKE SYSTEM
  1. Check for air leakage in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.) (Click here).

    HINT:
    1. If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake manifold increases and the air suction noise becomes louder.
    2. If Short FT #1 and Long FT #1 are largely different from the normal values (differ by more than 15%) when idling (intake air volume is small) and almost the same as the normal values when racing the engine (for example, when maintaining a speed of 3000 rpm) (intake air volume is high), air leakage may be present.

    OK:
    There is no air leakage.



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


51.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Disconnect the throttle with motor body assembly connector.

    HINT:
    When the connector is disconnected, the vehicle enters fail-safe mode and the throttle valve opening angle is 4 to 7°.

  1. Crank the engine and check that it starts.

    Result 
    Result
    Proceed to
    Engine starts
    A
    Engine does not start
    B

  1. Connect the throttle with motor body assembly connector.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



B
Go to step 53
A


52.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Check if carbon is in the air flow passage.

    OK:
    No carbon present.



NG
REMOVE FOREIGN OBJECT AND CLEAN THROTTLE WITH MOTOR BODY ASSEMBLY
OK


53.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
  1. Performing the Active Test, referring to DTC P0011 inspection procedure .

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B*1

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
    3. *1: From step 69, perform intake system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).



B
Go to step 69
A

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)  

54.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Check the harnesses and connectors, referring to DTC P0100 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness is normal, after replacing the mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs again, proceed to step 69 and perform intake system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASS AIR FLOW METER (Click here)  

55.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    If the engine coolant temperature sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


56.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0115 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


57.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).

HINT:
If the mass air flow meter is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


58.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Check the harnesses and connectors, referring to DTC P0100 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.
  3. If the wire harness or connector is malfunctioning, after replacing or repairing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


59.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT and Atmosphere Pressure.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    +25% or more or less than -25%
    1. Heated oxygen sensor
    2. Mass air flow meter
    3. Fuel injector assembly
    4. ECM
    A
    Atmosphere Pressure
    80 kPa or less (when altitude is 0 m)
    Both Data List items listed above
    Values are other than above
    -
    B



B
Go to step 63
A


60.PERFORM SIMULATION TEST
  1. Remove the EFI MAIN and ETCS fuses from the engine room relay block.

  1. After 60 seconds or more elapse, install the EFI MAIN and ETCS fuses.

  1. Check if the engine can be started.

    Result 
    Result
    Proceed to
    Engine can be started
    A
    Engine cannot be started
    B



B
Go to step 63
A


61.INSPECT HEATED OXYGEN SENSOR
A254132E06
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel System Status #1.

  1. Confirm that Fuel System Status #1 is CL.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Read the output voltage from the heated oxygen sensor when increasing and decreasing the fuel injection volume.

    Standard:
    Tester Display
    Injection Volume
    Specified Condition
    O2S B1S1
    +12%
    Heated oxygen sensor output voltage is higher than 0.5 V
    -12%
    Heated oxygen sensor output voltage is below 0.4 V

    Result 
    Result
    Proceed to
    Normal
    A
    Abnormal
    B

    HINT:
    1. The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
    2. If the heated oxygen sensor is malfunctioning, after replacing it, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



B
REPLACE HEATED OXYGEN SENSOR (SENSOR 1) (Click here)
A


62.PERFORM SIMULATION TEST
  1. Check if the idling speed is stable after starting the engine.

    OK:
    Engine speed is stable.

    HINT:
    After replacing the fuel injector assembly or mass air flow meter, check if engine starting trouble occurs again. If engine starting trouble occurs, replace the ECM. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK

REPLACE MASS AIR FLOW METER (Click here)  

63.CHECK FUEL PRESSURE
  1. Inspect the fuel pressure .



NG
Go to step 68
OK


64.INSPECT SPARK PLUG
  1. Inspect the spark plugs .

    Result 
    Result
    Proceed to
    All cylinders are normal
    A
    One cylinder is abnormal*1
    B
    All cylinders are abnormal*2, *3
    C

HINT:
  1. *1: If one cylinder is abnormal, replace the spark plug of that cylinder and inspect the ignition and fuel system for that cylinder. After performing repairs, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.
  2. *2: If all cylinders are abnormal, replace the spark plugs of all cylinders and check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.
  3. *3: Engine starting trouble may occur if the vehicle is driven extremely short distances repeatedly.



B
REPLACE SPARK PLUG (ABNORMAL CYLINDER) (Click here)

C
REPLACE SPARK PLUG (ALL CYLINDER) (Click here)
A


65.CONFIRM VEHICLE CONDITION
  1. Confirm the conditions present when the malfunction occurred based on the customer problem analysis.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    When the engine is stopped and a long time has passed, engine starting trouble occurs*1
    Pressure regulator is stuck open
    A
    When the engine is stopped and approximately 15 to 120 minutes have passed, engine starting trouble occurs*2
    Fuel injector leak
    B
    When the engine is stopped and approximately 2 to 3 minutes have passed, engine starting trouble occurs*3
    Failure to maintain fuel pressure by pressure regulator
    A
    Condition other than above, or there is an inconsistency in the conditions present when engine starting trouble occurs
    -
    C*4

    HINT:
    *1: The pressure regulator may be stuck open. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *2: Fuel may be leaking from a fuel injector assembly.
    *3: The pressure regulator may not be able to maintain the fuel pressure. Attach a fuel pressure gauge and check the ability to maintain fuel pressure after stopping the engine.
    *4: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



B
Go to step 67

C
Go to step 69
A


66.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Result 
    Result
    Proceed to
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    A
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    B*1

    HINT:
    1. If the engine cannot be started, check the fuel pressure after cranking the engine.
    2. *1: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



B
Go to step 69
A

REPLACE FUEL PRESSURE REGULATOR ASSEMBLY (Click here)  

67.INSPECT FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B*1

    HINT:
    1. If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.
    2. *1: From step 69, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



B
Go to step 69
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

68.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.
    3. If there are no fuel leaks, after inspecting the fuel pump control circuit, check if engine starting trouble occurs again. If engine starting trouble still occurs, proceed to step 69 and perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.



B
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
A

REPAIR OR REPLACE FUEL LINE 

69.CHECK MALFUNCTION CONDITION
  1. If the malfunction could not be identified during the inspection in steps 38, 39, 40 and 46, perform fuel system troubleshooting C (steps 70 to 73).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 38, 39, 40 and 46
    Fuel system troubleshooting C
    70 to 73
    A

  1. If the malfunction could not be identified during the inspection in step 44, perform ignition system troubleshooting (steps 74 to 79).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 44
    Ignition system troubleshooting
    74 to 79
    B

  1. If the malfunction could not be identified during the inspection in steps 53 and 54, perform intake air system troubleshooting (steps 80 to 82). If engine starting trouble still occurs, perform fuel system troubleshooting A (steps 83 to 90).

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Step 53 and 54
    Intake air system troubleshooting
    80 to 82
    C
    Fuel system troubleshooting A
    83 to 90

  1. If the malfunction could not be identified during the inspection in steps 55, 56, 57, 58, 61, 62, 64, 65, 66, 67 and 68, perform fuel system troubleshooting A (steps 91 to 98), fuel system troubleshooting B (steps 99 to 101), intake air system troubleshooting (steps 102 to 104), and ignition system troubleshooting (steps 105 to 110), in that order.

    Result 
    Performed Step
    Troubleshooting by System
    Procedure
    Proceed to
    Steps 55, 56, 57, 58, 61, 62, 64, 65, 66, 67 and 68
    Fuel system troubleshooting A
    91 to 98
    D
    Fuel system troubleshooting B
    99 to 101
    Intake air system troubleshooting
    102 to 104
    Ignition system troubleshooting
    105 to 110



B
Go to step 74

C
Go to step 80

D
Go to step 91
A


70.INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


71.CHECK TERMINAL VOLTAGE (FUEL INJECTOR CIRCUIT)
  1. Check the harnesses and connectors, referring to DTC P0300 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
CHECK FUEL INJECTOR CIRCUIT
OK


72.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 73
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

73.CHECK CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE) 

74.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


75.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the camshaft position sensor bolt.

  1. Check the connection of the camshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


76.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


77.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0340 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


78.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 79
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

79.CHECK CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE) 

80.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine and warm it up until the engine coolant temperature stabilizes with the A/C switch and all the accessory switches should be off

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 82
A


81.CHECK CYLINDER COMPRESSION PRESSURE
  1. Inspect the compression .



NG
CHECK AND REPAIR ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

82.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


83.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

    Standard:

    Vehicle State
    Specified Condition
    Cranking engine
    304 to 343 kPa (3.1 to 3.5 kgf/cm2)
    5 minutes after stopping engine
    147 kPa (1.5 kgf/cm2) or more



NG
Go to step 89
OK


84.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


85.PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


86.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


87.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


88.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

89.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    Fuel leakage or signs of fuel leakage are present
    A
    No fuel leakage or signs of fuel leakage
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
Go to step 90
A

REPAIR OR REPLACE FUEL LINE 

90.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

    HINT:
    1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
    2. Make sure the internal connector is securely connected.
    3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP (Click here)
OK

REPLACE FUEL PRESSURE REGULATOR (Click here)  

91.CHECK FUEL PRESSURE

HINT:
For the fuel pressure inspection, refer to the following procedures .

  1. Attach a fuel pressure gauge and check the fuel pressure after stopping the engine.

    Standard:
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)

    HINT:
    If the engine cannot be started, read the values after cranking the engine.


    Result 
    Result
    Proceed to
    147 kPa (1.5 kgf/cm2) or higher (5 minutes after stopping the engine)
    A
    Less than 147 kPa (1.5 kgf/cm2) (5 minutes after stopping the engine)
    B



B
Go to step 97
A


92.READ VALUE USING INTELLIGENT TESTER (LONG FT #1)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Long FT #1.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    Long FT #1
    -15 to +15%
    1. Wire harness or connector
    2. Fuel
    A
    +15% or more, or less than -15%
    Fuel injector assembly
    B



B
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
A


93.PERFORM SIMULATION TEST
  1. Check if the idling speed after starting the engine is currently stable and has always been stable in the past.

    Result 
    Problem Symptom
    Suspected Area
    Proceed to
    Current unstable idling speed or history of unstable idling speed
    Crankshaft position sensor system
    A
    All current and past idling speeds are stable
    Fuel
    B

    HINT:
    Through the customer problem analysis, confirm the fuel being used and the location at which the fuel was added to check if the malfunction is caused by the fuel in the vehicle.



B
REPLACE FUEL
A


94.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


95.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


96.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

97.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP/SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.

  1. When performing the Active Test, check for fuel leakage from the fuel pipes.

    Result 
    Result
    Proceed to
    No fuel leakage or signs of fuel leakage
    A
    Fuel leakage or signs of fuel leakage are present
    B

    HINT:
    1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
    2. When performing the Active Test, if there is no operating noise from the fuel pump, the fuel pump system may be malfunctioning.
    3. Check if the vehicle ran out of fuel, as engine starting trouble due to running out of fuel is also detected.



B
REPAIR OR REPLACE FUEL LINE
A


98.INSPECT FUEL PUMP
  1. Inspect the fuel pump (Click here).

    HINT:
    1. Make sure there is no foreign matter such as iron particles on the fuel pump and no signs that the fuel pump was stuck.
    2. Make sure the internal connector is securely connected.
    3. Make sure the fuel pump filter is not clogged.



NG
REPLACE FUEL PUMP (Click here)
OK


99.CHECK PURGE VSV


    A258724E02
  1. Disconnect the vacuum hose (on the canister side) of the purge VSV.
    Text in Illustration 
    *1
    Hose (to Canister)
    *2
    Connector
    *3
    Purge VSV

  1. Start the engine.

  1. Idle the engine.

  1. Disconnect the connector of the purge VSV.

  1. Check if air flows through the purge VSV.

    OK:
    Air Does not flow

  1. Connect the connector of the purge VSV.

  1. Connect the vacuum hose of the purge VSV.

    HINT:
    When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (Click here).



NG
INSPECT PURGE VSV (Click here)
OK


100.CHECK FUEL INJECTOR ASSEMBLY
  1. Clean the inside of the surge tank with compressed air.

  1. After stopping the engine, measure the HC concentration inside the surge tank for 15 minutes.

    Result 
    Result
    Proceed to
    400 ppm or higher
    A
    Less than 400 ppm
    B

    HINT:
    If the concentration is 400 ppm or higher, a fuel injector assembly may have a sealing problem.



B
Go to step 101
A

REPLACE FUEL INJECTOR ASSEMBLY (Click here)  

101.CHECK INTAKE VALVE
  1. Check if carbon is on the intake valves.

    Result 
    Result
    Proceed to
    Carbon present
    A
    No carbon present
    B



B
Go to step 102
A

CLEAN INTAKE VALVE 

102.READ VALUE USING INTELLIGENT TESTER (ISC LEARNING VALUE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ISC Learning Value.

    Result 
    Data List Item
    Result
    Suspected Area
    Proceed to
    ISC Learning Value
    (engine displacement (liters) x 0.9) or more
    1. Valve timing
    2. Compression
    A
    Less than (engine displacement (liters) x 0.9)
    -
    B



B
Go to step 104
A


103.CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the cylinder compression pressure .



NG
CHECK AND REPAIR ENGINE ASSEMBLY
OK

CHECK VALVE TIMING  

104.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


105.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the crankshaft position sensor bolt.

  1. Check the connection of the crankshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


106.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
  1. Check the tightening and installation condition of the camshaft position sensor bolt.

  1. Check the connection of the camshaft position sensor connector.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


107.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0335 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


108.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Check the harnesses and connectors, referring to DTC P0340 inspection procedure .

HINT:
  1. Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
  2. Make sure there is not an excessive amount of force applied to the wire harness.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


109.CHECK CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
Go to step 110
OK

END (CRANKSHAFT POSITION SENSOR IS DEFECTIVE) 

110.CHECK CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).

  1. Check the engine start operation.

    OK:
    Malfunction has been repaired successfully.



NG
REPLACE ECM (Click here)
OK

END (CAMSHAFT POSITION SENSOR IS DEFECTIVE)