Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404777 ENGINE ASSEMBLY A

M20A-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

·

Replacement of engine assembly

·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
Hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Front wheel alignment adjustment
1.

Clear zero point calibration data

2.

Perform yaw rate and acceleration sensor zero point calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.*1
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEELS

Hide 51410 6.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

a.
A431384

Remove the 4 bolts, 4 screws, 4 clips and No. 1 engine under cover assembly from the vehicle.


Hide 51444A 7.REMOVE REAR ENGINE UNDER COVER LH

a.
A431385

Remove the 6 clips and rear engine under cover LH from the vehicle.


Hide 51443C 8.REMOVE REAR ENGINE UNDER COVER RH

a.
A431386

Remove the 6 clips and rear engine under cover RH from the vehicle.


Hide 10.DRAIN ENGINE COOLANT (for Engine)

Hide 17751 13.REMOVE NO. 1 AIR CLEANER INLET

a.
A432798

Remove the 4 bolts and No. 1 air cleaner inlet from the upper radiator support sub-assembly and air cleaner case sub-assembly.


Hide 14.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 15.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 16.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A433045

Remove the 3 bolts and remove the air cleaner case sub-assembly.


Hide 82662A 18.REMOVE NO. 1 RELAY BLOCK COVER

a.
A433048

Disengage the claw and 2 guides to remove the No. 1 relay block cover from the engine room relay block.


Hide 19.REMOVE ENGINE WIRE

a.
A433049

Disconnect the 3 connectors from the engine room relay block.


b.

Disengage the 2 claws to separate the engine wire from the engine room relay block.


c.
A433050

Remove the nut.


d.

Disengage the 2 claws to separate the engine wire from the engine room relay block.


e.
A433051

Remove the 2 bolts to separate the engine wire from the vehicle.


f.
A433052

Disengage the 3 clamps to separate the engine wire from the vehicle.


Hide G9200 20.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide G92A0A 21.REMOVE INVERTER RESERVE TANK ASSEMBLY

a.
A433053

Remove the 2 bolts.


b.

Slide the clip and disconnect the No. 1 inverter cooling hose assembly from the inverter reserve tank assembly.


c.

Slide the clip and disconnect the inlet hybrid water pump hose from the inverter reserve tank assembly.


Hide 33820B 22.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365176

Remove the nut and disconnect the transmission control cable assembly from the control shaft lever.


b.

Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 16571C 23.DISCONNECT NO. 1 RADIATOR HOSE

A433054

a.

Disengage the clamp to separate the No. 1 radiator hose.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 24.DISCONNECT NO. 2 RADIATOR HOSE

a.
A434752

Disengage the 3 clamps to disconnect the No. 1 inverter cooling hose assembly and inlet hybrid water pump hose from the fan shroud assembly.


b.
A406659

Slide the clip and disconnect the No. 2 radiator hose from the water inlet sub-assembly.


Hide G922H 25.DISCONNECT INLET HYBRID RADIATOR HOSE

a.
A433056

Slide the clip and disconnect the inlet hybrid radiator hose from the motor cooling cooler.


Hide G922F 26.DISCONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.
A433055

Slide the clip and disconnect the outlet No. 1 hybrid water pump hose from the motor cooling cooler.


Hide 23829A 27.REMOVE NO. 1 FUEL VAPOR FEED HOSE

a.
A433057C01
2.219,1.719 1.958,1.948 1.958,1.948 2.198,1.583 true 1.792,1.885 2.021,2.073 0.229,0.188 10 false *a
*a Retainer
V100135

Pinch
V113148

Pull off


Pinch the retainer of the No. 1 fuel vapor feed hose connector, and then pull the No. 1 fuel vapor feed hose connector off of the No. 2 fuel vapor feed pipe.

NOTICE:

Be sure to disconnect the No. 1 fuel vapor feed hose connector by hand.



Hide 25860 28.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 29.REMOVE FUEL VAPOR FEED PIPE

a.
A433058

Disengage the clamp and remove the bolt to separate the engine wire.


b.

Disengage the clamp to separate the No. 1 fuel vapor feed hose.


c.

Remove the bolt and fuel vapor feed pipe from the fuel delivery guard.


Hide 23825 30.REMOVE FUEL DELIVERY GUARD

a.
A426103

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 87245 31.DISCONNECT INLET HEATER WATER HOSE

a.
A451412C01
2.208,0.844 2.469,0.625 true 2.469,0.521 2.656,0.719 0.188,0.198 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the inlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected water hose sub-assembly and inlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 87246 32.DISCONNECT OUTLET HEATER WATER HOSE

a.
A451413C01
1.906,0.313 1.625,0.625 true 1.896,0.229 2.104,0.427 0.208,0.198 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the outlet heater water hose.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected water hose sub-assembly and outlet heater water hose connector with plastic bags to prevent damage and contamination.


Hide 23901 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A433062

Disengage the clamp to separate the fuel tube sub-assembly.


b.

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M20A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 16283B 34.DISCONNECT WATER BY-PASS HOSE

a.
A433063

Slide the hose clip and disconnect the water by-pass hose from the No. 3 water by-pass pipe.


Hide 16267 35.SEPARATE NO. 3 WATER BY-PASS HOSE

a.
A433064

Disengage the clamp to separate the No. 3 water by-pass hose.


Hide 88703 36.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 37.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 38. SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 39.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 40.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 41.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 17410 42.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 51108A 44.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 45.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 46.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A434068

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A433065

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


d.
A433066

Remove the bolt and No. 2 engine mounting stay LH.


e.
A433067

Remove the 6 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


f.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 89481B 47.REMOVE DIFFERENTIAL PRESSURE SENSOR

Hide 48.REMOVE EMISSION CONTROL VALVE BRACKET

a.
C398735

Remove the bolt and emission control valve bracket from the cylinder head sub-assembly.


Hide 49.INSTALL ENGINE HANGER

a.
C398746C02
0.51,0.531 0.844,0.531 true 2.219,0.51 2.552,0.51 true 0.292,0.448 0.51,0.625 0.219,0.177 10 true *1 1.99,0.427 2.208,0.604 0.219,0.177 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Attach an engine sling device and hang the engine assembly with transaxle with a chain block.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedure while the engine assembly with transaxle is suspended because doing so may cause the engine assembly with transaxle to drop, resulting in injury. However, the engine assembly with transaxle needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 50.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A434061

Remove the 4 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 12305 51.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A434062

Remove the 2 bolts and No. 2 earth wire from the engine mounting insulator sub-assembly RH and vehicle.


b.
A434063

Remove the bolt, nut and disconnect the air conditioner tube and accessory assembly.


c.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 11363A 53.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A426082

Remove the flywheel housing side cover from the cylinder block sub-assembly.


Hide 23819 54.REMOVE NO. 2 FUEL VAPOR FEED PIPE

a.
A433548

Remove the bolt, nut and No. 2 fuel vapor feed pipe from the fuel hose brackets.


Hide 82121 56.REMOVE ENGINE WIRE

a.
A426083

Remove the 3 bolts.


b.
A434064

Remove the bolt.


c.
A434065

Remove the 3 bolts.


d.
A434066

Remove the bolt.


e.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 88370 58.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY

Hide 31270 59.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 19315 61.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 62.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 63.REMOVE ENGINE HANGER

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.