Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD) › 2012.02–2015.04
RM2030EQ _53 Suspension _014647 FRONT SUSPENSION _0281053 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge for LHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM

Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.SECURE STEERING WHEEL

Hide 5.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.REMOVE FRONT WHEELS

Hide 51442C 7.REMOVE ENGINE UNDER COVER LH

Hide 51441C 8.REMOVE ENGINE UNDER COVER RH

Hide 53737B 9.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 10.REMOVE FRONT FENDER APRON SEAL RH

Hide 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 13.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 53295E 14.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 11209 15.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 17752 16.REMOVE INLET NO. 2 AIR CLEANER

Hide 17735 17.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 18.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 19.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17751 21.REMOVE INLET NO. 1 AIR CLEANER

Hide 17805F 22.REMOVE INTAKE AIR RESONATOR SUB-ASSEMBLY

Hide 17119A 23.REMOVE AIR CLEANER BRACKET

Hide 17190 24.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

Hide 17584B 26.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Front Side)

Hide 17410 27.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 28.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 29.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side


Hide 48810 30.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 31.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 45470 32.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 33.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 48069 34.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 35.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 43420 36.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 37.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side


Hide 45220 38.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 12360 39.SEPARATE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

a.
A209884

Remove the 3 nuts and separate the front engine mounting insulator assembly from the front frame assembly.


Hide 12372A 40.SEPARATE ENGINE MOUNTING INSULATOR LH

a.

Remove the 2 hole plugs.


b.
A353344

Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.


Hide 12362 41.SEPARATE ENGINE MOUNTING INSULATOR RH

a.

Remove the 2 hole plugs.


b.
A209885

Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.


Hide 16571C 42.DISCONNECT NO. 1 RADIATOR HOSE

Hide 88704 43.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E255280

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E255281

Disconnect the suction hose sub-assembly.


c.

Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



d.
C312326

Disengage the clamp and disconnect the suction hose sub-assembly from the vehicle body.


Hide 88710E 44.DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

Hide 45.INSTALL ENGINE HANGERS

a.
C312246C01
1.354,3.354 1.76,3.354 true 2.948,0.677 2.438,0.677 true 1.802,3.271 2.021,3.479 0.219,0.208 10 true *2 2.979,0.594 3.219,0.771 0.24,0.177 10 false *1
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 and No. 2 engine hangers with the 4 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

Item Part No.
No. 1 engine hanger 12281-31120
No. 2 engine hanger 12281-31100
Bolt 91671-10825


Hide 46.INSTALL ENGINE SUPPORT BRIDGE

a.
C312330

Disconnect the pressure sensor assembly connector.


b.

Remove the 2 hood support assemblies.

Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>REMOVAL


c.

Install SST to the vehicle body as shown in the illustration.

SST
09940-10010  

C312302C01
2.583,2.375 2.521,2.375 2.521,2.375 2.406,2.49 false 5.156,2.458 5.094,2.458 5.094,2.458 4.927,2.76 false 5.135,3.708 6.146,3.708 false 2.927,5.74 1.854,5.74 false 5.552,5.906 4.302,5.906 false 5.438,7.104 5.531,7.104 5.531,7.104 5.729,6.781 false 1.927,6.813 1.844,6.813 1.844,6.813 1.667,6.573 false 4.948,7.792 5,7.792 5,7.792 5.094,8.198 false 5.729,7.792 5.781,7.792 5.781,7.792 5.854,8.198 false 2.25,7.75 2.177,7.75 2.177,7.75 2.115,8.198 false 1.344,7.75 1.271,7.75 1.271,7.75 1.198,8.198 false 0.479,0.927 0.667,1.115 0.188,0.188 10 true *g 2.948,5.656 3.135,5.854 0.188,0.198 10 false *a 0.917,1.885 1.104,2.073 0.188,0.188 10 false *d 2.615,2.281 2.802,2.469 0.188,0.188 10 false *c 5.177,2.385 5.365,2.573 0.188,0.188 10 false *c 6.198,3.635 6.531,3.802 0.333,0.167 10 false SST 6.438,0.938 6.625,1.125 0.188,0.188 10 true *g 6.031,1.896 6.219,2.083 0.188,0.188 10 false *d 4.125,5.823 4.313,6.021 0.188,0.198 10 false *a 5.271,7.021 5.458,7.219 0.188,0.198 10 false *b 5.573,7.708 5.76,7.906 0.188,0.198 10 false *b 4.792,7.708 4.979,7.906 0.188,0.198 10 false *b 2.271,7.677 2.458,7.875 0.188,0.198 10 false *b 1.354,7.677 1.542,7.875 0.188,0.198 10 false *b 0.948,6.948 1.135,7.146 0.188,0.198 10 false *e 2.5,6.948 2.688,7.146 0.188,0.198 10 false *f 4.542,6.979 4.729,7.177 0.188,0.198 10 false *f 6.063,6.979 6.25,7.177 0.188,0.198 10 false *e 1.958,6.76 2.146,6.958 0.188,0.198 10 false *b
*a Support Shaft *b Side Member
*c Cloth *d Front Side
*e Correct *f Incorrect
*g Front Suspension Nut - -


CAUTION:
·
C312303C05
1.761,2.043 1.964,2.235 0.203,0.191 10 *a 0.175,1.885 0.378,2.076 0.203,0.191 10 *a 0.57,0.075 0.773,0.266 0.203,0.191 10 *c 2.261,0.075 2.464,0.266 0.203,0.191 10 *d 0.136,2.338 0.340,2.530 0.203,0.191 10 *b 1.74,2.46 1.944,2.651 0.203,0.191 10 *b 0.405,1.987 0.51,1.987 0.51,1.987 0.797,2.456 false 0.35,2.426 0.465,2.426 0.465,2.426 0.781,2.709 false 1.991,2.133 2.078,2.133 2.078,2.133 2.475,2.448 false 1.971,2.545 2.091,2.545 2.091,2.545 2.477,2.723 false
*a Fuse Shackle
*b Shackle (A)
*c Correct
*d Incorrect


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·
C316804C03
1.396,1.052 1,1.052 false 0.792,0.969 1,1.156 0.208,0.188 10 false *a 0.854,1.802 1.063,1.99 0.208,0.188 10 false *b 2.354,1.802 2.563,1.99 0.208,0.188 10 false *c
*a Fuse Bolt
*b Correct
*c Incorrect


Make sure the fuse bolt is not deformed.



NOTICE:
·

Prevent SST from contacting the vehicle body or windshield.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed while performing work.

·

Set the support shafts on level surfaces.




d.
C312305C03
1.386,2.029 1.586,2.235 0.199,0.206 10 *a 1.913,2.338 2.112,2.544 0.199,0.206 10 *d 0.478,2.422 0.678,2.628 0.199,0.206 10 *c 0.253,0.975 0.452,1.181 0.199,0.206 10 *b 1.059,2.145 1.361,2.145 false 1.017,2.463 1.896,2.463 false 0.704,2.522 0.792,2.522 0.792,2.522 0.859,2.768 false 0.478,1.067 0.566,1.067 0.566,1.067 0.641,1.479 false
*a Support Shaft
*b Sub Beam
*c Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height and make the sub beams parallel to the ground.


e.

Connect each chain to the division bar with the shackles at the positions shown in the illustration.

C328302C01
0.854,1.833 0.365,1.833 false 2.542,5.042 2.24,5.042 false 1.927,4.188 1.969,4.833 1.969,4.833 1.813,4.833 false 0.906,3.865 0.875,4.198 0.875,4.198 0.719,4.198 false 2.583,1.115 2.594,1.823 false 1.635,1.229 1.938,2.24 1.938,2.24 2.26,2.24 false 1.24,0.979 1.365,1.146 0.125,0.167 10 true 1 1.073,1.219 1.198,1.385 0.125,0.167 10 true 2 0.76,1.417 0.885,1.583 0.125,0.167 10 true 3 2.125,4.156 2.25,4.323 0.125,0.167 10 true 1 2.198,4.354 2.323,4.521 0.125,0.167 10 true 2 2.323,4.469 2.448,4.635 0.125,0.167 10 true 3 2.531,1.875 2.844,2.073 0.313,0.198 10 false *a 2.26,2.271 2.573,2.469 0.313,0.198 10 false *b 0.219,1.76 0.531,1.958 0.313,0.198 10 false *1 1.635,4.76 1.948,4.958 0.313,0.198 10 false *b 0.531,4.125 0.844,4.323 0.313,0.198 10 false *a 2.573,4.979 2.885,5.177 0.313,0.198 10 false *2
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle


NOTICE:

Make sure that the chains are not twisted.



f.

Connect the 3rd link of the chain to the No. 1 engine hanger.


g.

Connect the 3rd link of the chain to the No. 2 engine hanger.


h.

Make sure the distance between the chain block assembly and suspension ring is 20 mm (0.787 in.) or more.

C312307C01
1.771,1.083 1.417,1.083 false 1.083,1.74 0.74,1.74 false 1.813,1.021 2,1.219 0.188,0.198 10 false *a 0.563,1.646 0.75,1.844 0.188,0.198 10 false *b 0.792,1.333 0.979,1.531 0.188,0.198 10 false *c
*a Chain Block Assembly *b Suspension Ring
*c 20 mm (0.787 in.) or more - -



i.

Adjust the position of the chain block assembly so that the chain is perpendicular to the main beam and sub beams as shown in the illustration.

C312308C01
3.833,1.073 3.552,1.073 false 4.177,0.406 4.073,0.406 4.073,0.406 4.01,0.729 false 5.427,1.917 6.083,1.917 false 1.104,1.927 1.76,1.927 false 3.885,0.99 4.073,1.208 0.188,0.219 10 false *a 4.24,0.302 4.427,0.521 0.188,0.219 10 false *b 3.385,0.281 3.573,0.5 0.188,0.219 10 false *h 5.583,1.406 5.771,1.625 0.188,0.219 10 false *i 1.51,1.406 1.698,1.625 0.188,0.219 10 false *i 6.125,1.823 6.313,2.042 0.188,0.219 10 false *c 0.906,1.833 1.094,2.052 0.188,0.219 10 false *c 1.094,3.302 1.281,3.521 0.188,0.219 10 false *f 4.521,3.26 4.708,3.479 0.188,0.219 10 false *g 1.615,0.167 1.781,0.323 0.167,0.156 10 false *d 5.354,0.167 5.521,0.323 0.167,0.156 10 false *e
*a Chain Block Assembly *b Main Beam
*c Sub Beam *d Dimension (A)
*e Dimension (B) *f Correct
*g Incorrect *h Right to Left Adjustment
*i Front to Rear Adjustment - -


CAUTION:

To prevent the engine with automatic transaxle assembly from falling, make sure that the dimension (A) and dimension (B) are equal.



j.

Tighten the 6 wing bolts and 2 bolts.

C312309

Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)


k.
C312310C01
1.445,0.766 1.637,0.981 0.192,0.215 10 *a
*a Approximately 50 mm (1.97 in.)


Move the chain block assembly approximately 50 mm (1.97 in.) as shown in the illustration.


l.
C312311C01
2.585,3.202 2.790,3.379 0.205,0.177 10 *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C316805C05
1.198,0.927 1.469,0.927 false 3.021,0.917 3.177,0.917 false 0.479,2.333 0.479,2.583 false 2.302,2.469 2.302,2.719 false 0.365,1.396 0.125,1.635 0.125,1.635 0.125,1.875 false 2.177,1.406 1.938,1.646 1.938,1.646 1.938,1.885 false 3.219,0.844 3.406,1.052 0.188,0.208 10 false *a 1.5,0.865 1.688,1.073 0.188,0.208 10 false *a 0.042,1.885 0.229,2.094 0.188,0.208 10 false *c 0.406,2.594 0.594,2.802 0.188,0.208 10 false *b 1.875,1.896 2.063,2.104 0.188,0.208 10 false *c 2.219,2.74 2.406,2.948 0.188,0.208 10 false *b 0.625,0.25 0.813,0.458 0.188,0.208 10 false *d 2.448,0.25 2.635,0.458 0.188,0.208 10 false *e
*a Chain Block Assembly
*b Suspension Ring
*c Roller
*d Incorrect
*e Correct


If the suspension ring contacts the roller of the chain block assembly, the chain block assembly may be damaged. Do not tighten the chain block assembly excessively.


NOTICE:
·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Do not shake the engine with automatic transaxle assembly excessively while it is being suspended.




Hide 47.INSTALL BELT

a.
C361604

Remove the bolt and nut.


b.
C362262

Loosen the bolt and disconnect the windshield washer jar assembly from the vehicle body.

NOTICE:

Do not remove the bolt.



c.

Install SST to the vehicle body as shown in the illustration.

SST
09727-00110  

C313705N02
4,3.833 6.125,3.833 true 2.948,3.833 0.823,3.833 true 6.177,3.75 6.719,4 0.542,0.25 10 false SST 0.469,3.771 1.01,4.021 0.542,0.25 10 false SST


d.

Using the ratchet buckle, tighten the belt until there is no slack.

C313706C01
3.656,2.188 6.094,2.188 true 3.323,2.208 0.875,2.208 true 2.448,1.073 1.938,1.448 1.938,1.448 1.844,1.448 true 4.531,1 5.167,1.531 5.167,1.531 5.292,1.531 true 6.135,2.115 6.635,2.385 0.5,0.271 10 false SST 0.552,2.125 1.052,2.396 0.5,0.271 10 false SST 1.677,1.365 2.042,1.542 0.365,0.177 10 false *a 5.323,1.448 5.688,1.625 0.365,0.177 10 false *a
*a Ratchet Buckle - -



Hide 51100G 48.REMOVE FRONT FRAME ASSEMBLY

a.
A268430

Disconnect the 2 clamps.


b.
C319462C01
1.482,0.593 1.116,0.593 false 0.916,0.499 1.166,0.667 0.250,0.168 10 *a
*a Chain Block Assembly


Wind the chain with the chain block assembly to lift the engine with automatic transaxle assembly.

NOTICE:
·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Lift the engine with automatic transaxle assembly until the engine is slightly raised off the front frame assembly.

·

Do not lift the engine with automatic transaxle assembly excessively.




c.
C310125C03
1.354,0.49 1.354,0.927 true 0.906,0.5 0.906,0.656 0.906,0.656 1.354,0.656 true 2.417,0.458 2.417,0.896 true 2.677,0.49 2.677,0.646 2.677,0.646 2.417,0.646 true 0.531,0.74 0.531,0.948 true 0.438,0.948 0.625,1.125 0.188,0.177 10 false *a 1.271,0.948 1.458,1.125 0.188,0.177 10 false *b 2.333,0.917 2.521,1.094 0.188,0.177 10 false *b
*a Engine Lifter
*b Attachment
V100145

Attachment Placement Location


Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
·

The front frame assembly is a heavy component. Make sure that it is supported securely.

·

Make sure to secure the front frame assembly to prevent it from dropping.



NOTICE:

Use the attachments to keep the front frame assembly level.



d.
A255441

Remove the 4 bolts, 2 nuts and frame side rail plates RH and LH.


e.

Remove the 4 bolts, 2 nuts and front suspension member rear braces RH and LH.


f.

Slowly lower the front frame assembly.

NOTICE:

When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48829A 49.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 50.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 51.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.


Hide 52.REMOVE STEERING LINK ASSEMBLY

Hide 48069 53.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 54.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 51227B 55.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.
C221242

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 52213A 56.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 57.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 58.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C169231C05
1.188,1.01 1.365,1.01 1.365,1.01 1.49,1.427 false 1.927,0.823 2.323,0.823 false 2.74,2.188 2.292,2.188 false 2.573,2.875 2.635,2.875 2.635,2.875 2.635,2.198 false 1.01,0.938 1.271,1.135 0.26,0.198 10 false *1 2.385,0.729 2.708,0.875 0.323,0.146 10 false SST 2.771,2.104 3.094,2.25 0.323,0.146 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C03
0.698,2.99 1,2.99 false 2.823,0.719 2.823,0.469 false 2.594,2.917 2.896,2.917 false 0.417,2.917 0.875,3.115 0.458,0.198 10 false SST 2.74,0.708 2.938,0.917 0.198,0.208 10 false *a 2.927,2.844 3.125,3.052 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 59.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C169231C06
1.188,1.01 1.365,1.01 1.365,1.01 1.49,1.427 false 1.927,0.823 2.323,0.823 false 2.74,2.188 2.292,2.188 false 2.563,2.875 2.625,2.875 2.625,2.875 2.625,2.198 false 1.01,0.938 1.208,1.125 0.198,0.188 10 false *1 2.385,0.729 2.708,0.875 0.323,0.146 10 false SST 2.771,2.104 3.094,2.25 0.323,0.146 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C03
0.677,3.031 0.99,3.031 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.396,2.969 0.854,3.167 0.458,0.198 10 false SST 2.625,0.781 2.938,0.938 0.313,0.156 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 60.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as the LH side.


Hide 61.REMOVE HOLE PLUG

a.

Remove 5 hole plugs from the front frame assembly.