Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM J

N04C-VQ ENGINE CONTROL  ECD SYSTEM  Lack of Power or Hesitation  


DESCRIPTION

Malfunction Condition Main Trouble Areas Related Trouble Areas
·

Lack of power caused by abnormal fuel injection volume (injection or supply pump assembly malfunction or injector assembly malfunction)

·

Lack of power caused by intake air volume shortage (turbocharger sub-assembly malfunction, front exhaust pipe assembly or center exhaust pipe assembly (catalyst converter) blocked)


1.

Injector assembly malfunctions

-

Injector assembly sliding malfunction

-

Injector assembly stuck closed

-

Injector assembly stuck open

-

Deposits in injector assembly

-

Injector assembly circuit malfunction


2.

Abnormal common rail pressure

-

Injection or supply pump assembly


3.

Abnormal intake air volume

-

Turbocharger sub-assembly

-

Center exhaust pipe assembly blockage



·

Pressure limiter (built into common rail assembly)

·

Intake air system leakage

·

Intake air system blockage

·

EGR system

·

Fuel filter element is clogged

·

Throttle valve (built into diesel throttle body assembly)

·

Compression pressure

·

Injector compensation code

·

Fuel leak

·

Fuel pressure sensor (built into common rail assembly)

·

Injector driver assembly

·

Vehicle modifications

·

Low quality fuel

·

Frozen fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.

·

This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Before troubleshooting, conduct the following:

1.

Check the fuel quality.

2.

Check the fuel for air.

3.

Check the fuel system for blockages.

4.

Check the air filter.

5.

Check the engine oil.

6.

Check the engine coolant.

7.

Check the engine idling speed and the maximum engine speed.

8.

Check the vacuum pump.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR IN ENGINE ROOM
a.

Check the wire harness and connector connections of the common rail system components.

HINT:

Check the following components and systems:

·

Sensors

·

Injection or supply pump assembly

·

Common rail assembly

·

Injector assemblies

·

Injector driver assembly

·

Turbocharger system

·

Intake and exhaust systems



OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

2.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to store DTCs relating to malfunctions of the fuel system, EGR system, and throttle valve. If DTCs are stored, problem areas can be identified.


a.

Start the engine (Procedure "A").


b.

Stop the engine and wait for at least 10 seconds (Procedure "B").


c.

Perform steps "A" (See procedure "A") and "B" (See procedure "B") again described above (to allow the ECM to store pressure limiter malfunction DTCs).



e.

Fully warm up the engine.


f.

Allow the engine to idle for 5 minutes or more.


g.

Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "C").


h.

Decelerate and stop the vehicle (Procedure "D").


i.

Repeat steps "C" (See procedure "C") and "D" (See procedure "D") 4 times or more.


j.

Stop the engine and wait for at least 10 seconds (Procedure "E").


k.

Repeat steps "C" (See procedure "C") and "E" (See procedure "E") described above (to store DTCs relating to the EGR system and throttle valve).


l.

Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to store DTCs relating to the injection or supply pump assembly).


Result:
Proceed to
NEXT



NEXT

3.READ OUTPUT DTC (RELATING TO ENGINE)
3.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


e.

Read the pending DTCs.


Result:
Result Proceed to
DTC is not output A
Engine related DTCs are output B



A

4.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

4.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail assembly internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail assembly pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No leakage.



Result:
Proceed to
OK
NG



OK

5.CHECK WHITE SMOKE

NG

REPAIR OR REPLACE FUEL LEAKAGE POINT

5.CHECK WHITE SMOKE
a.

Rev up the engine from idling to 3000 rpm several times to check whether white smoke is emitted from the exhaust pipe.


b.

Check that the intake system pipes and hoses are not excessively contaminated with oil.If white smoke is emitted from the intake system, its pipes and hoses are excessively contaminated with oil. If the presence of white smoke in the exhaust gas is confirmed, there is a high possibility of mechanical problems in the turbocharger sub-assembly or engine assembly.


Result:
Result Proceed to
No problems described above A
White smoke emitted, or intake system pipes and hoses excessively contaminated with oil B



A

6.READ VALUE USING GTS

B

32.INSPECT TURBOCHARGER SUB-ASSEMBLY
6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAP

·

MAF

·

Fuel Press


Standard:
GTS Display Condition*1 Standard Range Description
MAP Ignition switch ON (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
Idling 90 to 110 kPa (675 to 825 mmHg, 26.58 to 32.49 in.Hg) or less
3600 rpm (no engine load) 128 to 165 kPa (960 to 1238 mmHg, 37.80 to 48.73 in.Hg)
MAF Ignition switch ON (engine stopped) 0 gm/s Intake air volume detected by mass air flow meter sub-assembly
Idling 5 to 20 gm/s
3600 rpm (no engine load) 125 to 165 gm/s
Fuel Press Idling 20000 to 30000 kPa Common rail assembly internal fuel pressure


Result:
Item Result Proceed to
MAP, MAF, and Fuel press Standard range A
MAP and MAF Outside standard range B
Only MAP Outside standard range C
Only MAF Outside standard range D
Only Fuel Press Outside standard range E


HINT:

*1: The A/C switch and all accessory switches should be off with a fully-warmed engine.




A

7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)

C

GO TO DTC P0107 AND P0108 (RELATED TO MANIFOLD ABSOLUTE PRESSURE SENSOR)

D

GO TO DTC P0102 AND P0103 (RELATED TO MASS AIR FLOW METER)

E

23.CHECK AND REPLACE FUEL FILTER ASSEMBLY

B

28.INSPECT EGR VALVE ASSEMBLY
7.READ VALUE USING GTS (INJECTION FEED BACK VAL AND INJECTION VOLUME)
a.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Standard Range Description
Injection Feedback Val #1 Idling -2.0 to 2.0 mm3/st Value of injector assembly fuel injection volume compensates for differences in combustion condition of cylinders
·

Positive values indicate control which corrects combustion degradation

·

Negative values indicate control which corrects excessive combustion pressure

·

If problems exist, "Injection Feedback Val" may deviate from the -2.0 and 2.0 mm3/st


Injection Feedback Val #2 Idling -2.0 to 2.0 mm3/st
Injection Feedback Val #3 Idling -2.0 to 2.0 mm3/st
Injection Feedback Val #4 Idling -2.0 to 2.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st Fuel injection volume controlled by ECM
·

Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, manifold absolute pressure, atmospheric pressure, and EGR volume.

·

If problems exist, "Injection Volume" may be outside the standard range




Result:
Result Proceed to
Standard range A
Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range B


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.




A

8.CHECK INJECTOR COMPENSATION CODE

B

13.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR ASSEMBLY
8.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



b.

Check the injector compensation code.

OK:

Compensation code of the installed injector assembly is the same as the one registered in the ECM.



Result:
Proceed to
OK
NG



OK

9.RESET ECM

NG

REGISTER INJECTOR COMPENSATION CODE

9.RESET ECM
a.

Disconnect the cable from the negative battery terminal for at least 2 minutes.


b.

Reconnect the cable to the negative battery terminal.


c.

Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

10.BLEED AIR FROM FUEL SYSTEM
10.BLEED AIR FROM FUEL SYSTEM
a.

To bleed air from the priming pump, pump the priming pump until it becomes hard and cannot be pumped any more.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER LACK OF POWER HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER LACK OF POWER HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the lack of power has been successfully repaired by performing a driving test. Use the freeze frame data recorded at the time the malfunction occurred.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

12.CHECK INTAKE SYSTEM
12.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No leakage or blockage.



Result:
Proceed to
NEXT



NEXT

END

13.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR ASSEMBLY
a.

Follow the instructions in the table below according to the check result of the GTS.

HINT:

This operation is based on the premise that the common rail pressure is normal.


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -2.0 to 2.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


Result:
Injection Feedback Val #1 to #4 Injection volume
Less than 5.0 mm3/st Between 5.0 and 23.0 mm3/st (Normal) More than 23.0 mm3/st
2.0 mm3/st or more, -2.0 mm3/st or less A B B
Between -2.0 and 2.0 mm3/st - Normal C*

Proceed to Inspection Areas Descriptions
A Inspect and repair cylinder injector assembly with revised injection volume of less than -2.0 mm3/st:
·

Perform power balance inspection and identify malfunctioning cylinder

·

Replace malfunctioning cylinder injector assembly


Abnormal cylinder injector assembly injects excessively large quantity of fuel
B Identify malfunctioning cylinders by conducting power balance inspection:
·

Perform power balance inspection to identify malfunctioning cylinders

·

Clean malfunctioning cylinder injector assembly, then check and repair it


·

Fuel injection volume too low due to injector assembly nozzle being blocked by deposits

·

Abnormal cylinder injector assembly compression decreases

·

Abnormal cylinder injector assembly injects excessively large quantity of fuel


C Inspect and repair all cylinder injector assemblies:
Clean all cylinder injector assemblies, inspect, and repair them
All cylinder injector assemblies inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector assembly nozzles being blocked by deposits


HINT:

*: When the Injection Volume displayed on the GTS is large despite the Fuel Pressure and Injection Feedback Val #1 to #4 in the Data List being normal, the injector may be clogged. In this case, there may be deposits inside or outside the tip of the injector assembly.

·

Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).

·

Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.





A

14.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

B

15.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

C

20.CHECK INJECTOR ASSEMBLY FOR DEPOSITS
14.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.


d.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

15.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.


d.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.CHECK CYLINDER COMPRESSION PRESSURE
16.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VQ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

17.CHECK MALFUNCTIONING CYLINDER'S INJECTOR ASSEMBLY FOR DEPOSITS

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

17.CHECK MALFUNCTIONING CYLINDER'S INJECTOR ASSEMBLY FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Injector Condition Proceed to
Deposits A
No deposits B



A

18.CLEAN INJECTOR ASSEMBLY

B

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

18.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -2.0 to 2.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:
·

The A/C switch and all accessory switches should be off with a fully-warmed engine.

·

When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

20.CHECK INJECTOR ASSEMBLY FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Injector Condition Proceed to
Deposits A
No deposits B



A

21.CLEAN INJECTOR ASSEMBLY

B

21.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

22.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
22.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -2.0 to 2.0 mm3/st
Injection Volume #1 to #4 Idling 5.0 to 15.0 mm3/st


HINT:
·

*: The A/C switch and all accessory switches should be off with a fully-warmed engine.

·

When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.



OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

23.CHECK AND REPLACE FUEL FILTER ASSEMBLY
Result:
Proceed to
NEXT



NEXT

24.READ VALUE USING GTS
24.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus and read the values.Fuel Press

Standard:
GTS Display Condition *1 Reference Value
Fuel Press Idling 20000 to 30000 kPa


HINT:

*1: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

25.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
25.INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Inspect the common rail assembly (fuel pressure sensor) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>COMMON RAIL>REMOVAL).


Result:
Proceed to
OK
NG



OK

26.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY

NG

REPLACE COMMON RAIL ASSEMBLY

26.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY
a.

Inspect the injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>REMOVAL).


Result:
Proceed to
OK
NG



OK

27.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

27.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

CHECK AND REPLACE COMMON RAIL ASSEMBLY (PRESSURE LIMITER)

NG

REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY

28.INSPECT EGR VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

29.INSPECT DIESEL THROTTLE BODY ASSEMBLY

NG

29.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Actual Throttle Position.


e.

Read the value.

Standard:
Ignition switch to ON:

0%

Idling (Warmed up engine):

81 to 95%

Accelerator pedal fully depressed:

0%



Result:
Proceed to
OK
NG



OK

30.CHECK INTAKE SYSTEM

NG

30.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

31.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

31.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

32.INSPECT TURBOCHARGER SUB-ASSEMBLY

NG

REPLACE EXHAUST RETARDER ASSEMBLY

32.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check the turbocharger sub-assembly (Click hereEngine / Hybrid System>N04C-VQ (INTAKE)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

33.READ VALUE USING GTS

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY

33.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAP

·

MAF

·

Fuel Press


Standard:
GTS Display Condition*1 Standard Range Description
MAP Ignition switch ON (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by manifold absolute pressure sensor
Idling 90 to 110 kPa (675 to 825 mmHg, 26.58 to 32.49 in.Hg) or less
3600 rpm (no engine load) 128 to 165 kPa (960 to 1238 mmHg, 37.80 to 48.73 in.Hg)
MAF Ignition switch ON (engine stopped) 0 gm/s Intake air volume detected by mass air flow meter sub-assembly
Idling 5 to 20 gm/s
3600 rpm (no engine load) 125 to 165 gm/s


HINT:

*: The A/C switch and all accessory switches should be off with a fully-warmed engine.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

34.REPLACE CENTER EXHAUST PIPE ASSEMBLY
34.REPLACE CENTER EXHAUST PIPE ASSEMBLY
a.

Replace the center exhaust pipe assembly (Click hereEngine / Hybrid System>N04C-VQ EXHAUST>EXHAUST PIPE>REMOVAL).


Result:
Proceed to
NEXT



NEXT

35.READ VALUE USING GTS
35.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAP

·

MAF


Standard:
GTS Display Condition*1 Standard Range Description
MAP 3600 rpm (no engine load) 128 to 165 kPa (960 to 1237 mmHg, 37.78 to 48.71 in.Hg) Intake manifold internal pressure detected by manifold absolute pressure sensor


HINT:

*1: The A/C switch and all accessory switches should be off with a fully-warmed engine.


OK:

The values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE TURBOCHARGER SUB-ASSEMBLY