| Malfunction Condition | Main Trouble Areas | Related Trouble Areas |
|---|---|---|
·
Lack of power caused by abnormal fuel injection volume (injection or supply pump assembly malfunction or injector assembly malfunction) ·
Lack of power caused by intake air volume shortage (turbocharger sub-assembly malfunction, front exhaust pipe assembly or center exhaust pipe assembly (catalyst converter) blocked) |
1.
Injector assembly malfunctions -
Injector assembly sliding malfunction -
Injector assembly stuck closed -
Injector assembly stuck open -
Deposits in injector assembly -
Injector assembly circuit malfunction 2.
Abnormal common rail pressure -
Injection or supply pump assembly 3.
Abnormal intake air volume -
Turbocharger sub-assembly -
Center exhaust pipe assembly blockage |
·
Pressure limiter (common rail assembly) ·
Intake air system leakage ·
Intake air system blockage ·
Fuel filter element sub-assembly is clogged ·
Throttle valve (venturi assembly) ·
Compression pressure ·
Injector compensation code ·
Fuel leak ·
Fuel pressure sensor (common rail assembly) ·
Injector driver ·
Vehicle modifications ·
Low quality fuel ·
Frozen fuel ·
ECM |
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
This troubleshooting procedure checks for the cause of an obvious lack of engine power (the vehicle speed does not reach the target speed in the high speed range) while the vehicle is being driven.
After replacing the injection or supply pump assembly or suction control valve, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
After replacing the venturi assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Before troubleshooting, conduct the following:
Check the fuel quality.
Check the fuel for air.
Check the fuel system for blockages.
Check the air filter.
Check the engine oil.
Check the engine coolant.
Check the engine idling speed and the maximum engine speed.
Check the vacuum pump.
Check the wire harness and connector connections of the common rail system components.
Check the following components and systems:
Sensors
Injection or supply pump assembly
Common rail assembly
Injector assemblies
Injector driver
Turbocharger system
Intake and exhaust systems
The wire harnesses and connectors are connected securely.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Drive the vehicle according to the driving pattern below to allow the ECM to store DTCs related to malfunctions of the fuel system and throttle valve. If DTCs are stored, problem areas can be identified.
Start the engine (Procedure "A").
Stop the engine and wait for at least 10 seconds (Procedure "B").
Perform steps "A" (See procedure "A") and "B" (See procedure "B") again described above (to allow the ECM to store pressure limiter malfunction DTCs).
Enter Check Mode (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>CHECK MODE PROCEDURE).
Fully warm up the engine.
Allow the engine to idle for 5 minutes or more.
Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "C").
Decelerate and stop the vehicle (Procedure "D").
Repeat steps "C" (See procedure "C") and "D" (See procedure "D") 4 times or more.
Stop the engine and wait for at least 10 seconds (Procedure "E").
Repeat steps "C" (See procedure "C") and "E" (See procedure "E") described above (to store DTCs relating to the throttle valve).
Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to store DTCs relating to the injection or supply pump assembly).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| Engine related DTCs are output | B |
A
B
By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail assembly internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail assembly pressure.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.
Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.
There may be fuel leaks inside the components, such as the injection or supply pump assembly.
No leakage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Rev up the engine from idling to 3000 rpm several times to check whether white smoke is emitted from the exhaust pipe.
Check that the intake system pipes and hoses are not excessively contaminated with oil. If white smoke is emitted from the intake system, its pipes and hoses are excessively contaminated with oil. If the presence of white smoke in the exhaust gas is confirmed, there is a high possibility of mechanical problems in the turbocharger sub-assembly or engine assembly.
| Result | Proceed to |
|---|---|
| No problems described above | A |
| White smoke emitted, or intake system pipes and hoses excessively contaminated with oil | B |
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
MAP
Fuel Press
| GTS Display | Condition* | Standard Range | Description |
|---|---|---|---|
| MAP | Ignition switch ON (engine stopped) | Same as atmospheric pressure | Intake manifold internal pressure detected by vacuum sensor |
| Idling | 93 to 100 kPa (698 to 750 mmHg) or less | ||
| 3000 rpm (no engine load) | 110 to 140 kPa (825 to 1050 mmHg) or more | ||
| Fuel Press | Idling | 25000 to 35000 kPa | Common rail assembly internal fuel pressure |
| Item | Result | Proceed to |
|---|---|---|
| MAP and Fuel Press | Standard range | A |
| Only MAP | Outside standard range | B |
| Only Fuel Press | Outside standard range | C |
*: The A/C switch and all accessory switches should be off with a fully-warmed engine.
A
B
C
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3 and #4
Injection Volume
| GTS Display | Condition* | Standard Range | Description |
|---|---|---|---|
| Injection Feedback Val #1 | Idling | -7.0 to 7.0 mm3/st | Value of injector assembly fuel injection volume compensates for differences in combustion condition of cylinders
·
Positive values indicate control which corrects combustion degradation ·
Negative values indicate control which corrects excessive combustion pressure ·
If problems exist, "Injection Feedback Val" may deviate from -7.0 and 7.0 mm3/st |
| Injection Feedback Val #2 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Feedback Val #3 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Feedback Val #4 | Idling | -7.0 to 7.0 mm3/st | |
| Injection Volume | Idling | 5.0 to 15.0 mm3/st | Fuel injection volume controlled by ECM
·
Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, manifold absolute pressure and atmospheric pressure ·
If problems exist, "Injection Volume" may be outside the standard range |
| Result | Proceed to |
|---|---|
| Standard range | A |
| Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range | B |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
A
B
Read the injector compensation code (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
If the injector compensation code is not correctly registered, it may cause malfunctions (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Check the injector compensation code.
Compensation code of the installed injector assembly is the same as the one registered in the ECM.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative battery terminal for at least 2 minutes.
Reconnect the cable to the negative battery terminal.
Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.
Malfunction has been repaired successfully.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
To bleed air from the fuel system, pump the hand pump until it becomes hard and cannot be pumped any more.
| Proceed to |
|---|
| NEXT |
NEXT
Check whether the lack of power has been successfully repaired by performing a driving test. Use the freeze frame data recorded at the time the malfunction occurred.
Malfunction has been repaired successfully.
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.
Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.
No leakage or blockage.
| Proceed to |
|---|
| NEXT |
NEXT
Follow the instructions in the table below according to the check result of the GTS.
This operation is based on the premise that the common rail assembly pressure is normal.
| GTS Display | Condition* | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume | Idling | 5.0 to 15.0 mm3/st |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
| Injection Feedback Val #1 to #4 | Injection Volume | ||
|---|---|---|---|
| Less than 5.0 mm3/st | Between 5.0 and 23.0 mm3/st (Normal) | More than 23.0 mm3/st | |
| 7.0 mm3/st or more, -7.0 mm3/st or less | A | B | B |
| Between -7.0 and 7.0 mm3/st | - | Normal | C* |
| Proceed to | Inspection Areas | Descriptions |
|---|---|---|
| A | Inspect and repair cylinder injector assembly with revised injection volume of less than -7.0 mm3/st:
·
Perform power balance inspection and identify malfunctioning cylinder ·
Replace malfunctioning cylinder injector assembly |
Abnormal cylinder injector assembly injects excessively large quantity of fuel |
| B | Identify malfunctioning cylinders by conducting power balance inspection:
·
Perform power balance inspection to identify malfunctioning cylinders ·
Clean malfunctioning cylinder injector assembly and check it |
·
Fuel injection volume too low due to injector assembly nozzle being blocked by deposits ·
Abnormal cylinder compression decreases ·
Abnormal cylinder injector assembly injects excessively large quantity of fuel |
| C | Inspect and repair all cylinder injector assemblies:
Clean all cylinder injector assemblies and check them |
All cylinder injector assemblies inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector assembly nozzles being blocked by deposits |
*: When the Injection Volume displayed on the GTS is large despite the Fuel Pressure and Injection Feedback Val #1 to #4 in the Data List being normal, the injector may be clogged. In this case, there may be deposits inside or outside the tip of the injector assembly.
Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).
Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinders malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.
A
B
C
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder #1, #2, #3 and #4 Fuel Cut.
Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder #1, #2, #3 and #4 Fuel Cut.
Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
| Proceed to |
|---|
| NEXT |
NEXT
Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector assembly for any deposits.
| Injector Condition | Proceed to |
|---|---|
| Deposits | A |
| No deposits | B |
A
B
Wipe away deposits from the tips of the injector assemblies.
Solvent or carbon removal agents help remove deposits easily.
Exercise extreme care not to damage the injector assemblies while wiping off the deposits.
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall the injector assembly.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3 and #4
Injection Volume
| GTS Display | Condition* | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume | Idling | 5.0 to 15.0 mm3/st |
The A/C switch and all accessory switches should be off with a fully-warmed engine.
When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.
Values are within the standard range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.
Check the injector assembly for any deposits.
| Injector Condition | Proceed to |
|---|---|
| Deposits | A |
| No deposits | B |
A
B
Wipe away deposits from the tips of the injector assemblies.
Solvent or carbon removal agents help remove deposits easily.
Exercise extreme care not to damage the injector assemblies while wiping off the deposits.
| Proceed to |
|---|
| NEXT |
NEXT
Reinstall the injector assembly.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
Injection Feedback Val #1, #2, #3 and #4
Injection Volume
| GTS Display | Condition* | Reference Value |
|---|---|---|
| Injection Feedback Val #1 to #4 | Idling | -7.0 to 7.0 mm3/st |
| Injection Volume #1 to #4 | Idling | 5.0 to 15.0 mm3/st |
*: The A/C switch and all accessory switches should be off with a fully-warmed engine.
When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.
Values are within the standard range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check and replace the fuel filter element sub-assembly (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL FILTER>REPLACEMENT).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Enter the following menus and read the values.
| GTS Display | Condition* | Reference Value |
|---|---|---|
| Fuel Press | Idling | 25000 to 35000 kPa |
*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.
The values are within the standard range.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the fuel pressure sensor (common rail assembly) (Click hereEngine / Hybrid System>N04C-VL (FUEL)>COMMON RAIL>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the suction control valve (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL SUPPLY PUMP>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.
Read the value.
| Engine Speed | Result |
|---|---|
| Idling | 1350 to 2200 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Actual Throttle Position.
Read the value.
0%
81 to 95%
0%
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.
Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.
No leakage or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the exhaust retarder assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the turbocharger sub-assembly (Click hereEngine / Hybrid System>N04C-VL (INTAKE)>TURBOCHARGER>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Enter the following menus in order and read the values.
| GTS Display | Condition* | Standard Range | Description |
|---|---|---|---|
| MAP | Ignition switch ON (engine stopped) | Same as atmospheric pressure | Intake manifold internal pressure detected by vacuum sensor |
| Idling | 93 to 100 kPa (698 to 750 mmHg) or less | ||
| 3000 rpm (no engine load) | 110 to 140 kPa (825 to 1050 mmHg) or more |
*: The A/C switch and all accessory switches should be off with a fully-warmed engine.
The values are within the standard range.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the center exhaust pipe assembly (Click hereEngine / Hybrid System>N04C-VL EXHAUST>EXHAUST PIPE>REMOVAL).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Enter the following menus in order and read the values.
| GTS Display | Condition* | Standard Range | Description |
|---|---|---|---|
| MAP | 3000 rpm (no engine load) | 110 to 140 kPa (825 to 1050 mmHg) or more | Intake manifold internal pressure detected by vacuum sensor |
*: The A/C switch and all accessory switches should be off with a fully-warmed engine.
The values are within the standard range.
| Proceed to |
|---|
| OK |
| NG |
OK
NG