1.CHECK INJECTOR COMPENSATION CODE
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
58521D
3.REMOVE ENGINE SERVICE HOLE COVER MAT
Remove the engine service hole cover mat.
58410
4.REMOVE ENGINE SERVICE HOLE COVER
Detach the 2 hooks, 2 guides and remove the engine service hole cover.
58734B
5.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP
Remove the rear engine service cover weatherstrip.
58420
6.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY
| *a | Knob |
Turn the knob to detach the hook, detach the 2 guides and remove the No. 2 engine service hole cover assembly.
58123A
7.REMOVE SHIFT AND SELECT LEVER SUPPORT WITH BOOTS (for Manual Transmission)
Remove the shift lever knob sub-assembly.
Remove the transmission cover mat.
Remove the 4 bolts and remove the shift and select lever support with boots.
58841A
8.REMOVE SHIFTING HOLE COVER (for Automatic Transmission)
33820B
9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
for Manual Transmission:
Remove the nut, plate washer, 3 clips and disconnect the transmission control cable assembly.
for Automatic Transmission:
Remove the clip and plate washer and disconnect the transmission control cable assembly from the transmission floor shift assembly.
Remove the clip.
Remove the bolt and clamp.
Disconnect the transmission control cable assembly from the front engine service cover panel sub-assembly.
58701A
10.REMOVE FRONT ENGINE SERVICE COVER PANEL SUB-ASSEMBLY
for Automatic Transmission:
Disconnect the 2 connectors from the transmission floor shift assembly.
Remove the 5 bolts and front engine service cover panel sub-assembly.
51441D
11.REMOVE NO. 1 ENGINE UNDER COVER
51446C
12.REMOVE ENGINE UNDER COVER BRACKET LH
Remove the 2 bolts and the engine under cover bracket LH.
51445D
13.REMOVE ENGINE UNDER COVER BRACKET RH
Remove the 2 bolts and the engine under cover bracket RH.
53712C
14.REMOVE FRONT FENDER APRON LH
Remove the 6 bolts and the front fender apron LH.
53711C
15.REMOVE FRONT FENDER APRON RH
Remove the 7 bolts and the front fender apron RH.
16.DRAIN ENGINE OIL
17.DRAIN ENGINE COOLANT
18.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
19.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
20.DRAIN POWER STEERING FLUID
16400
21.REMOVE RADIATOR ASSEMBLY
17410
22.REMOVE FRONT EXHAUST PIPE ASSEMBLY
46700
23.REMOVE EXHAUST RETARDER ASSEMBLY
25608
24.REMOVE EGR COOLER SUB-ASSEMBLY
28100
25.REMOVE STARTER ASSEMBLY
44348A
26.DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE
Slide the clamp and disconnect the No. 1 oil reservoir to pump hose from the vane pump assembly.
44411
27.DISCONNECT PRESSURE FEED HOSE
Remove the union bolt and disconnect the pressure feed hose from the vane pump assembly.
Remove the gasket from the pressure feed hose.
27020
28.REMOVE GENERATOR ASSEMBLY
37140
29.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
45470
30.DISCONNECT TIE ROD ASSEMBLY LH
Remove the cotter pin.
Remove the nut.
Using SST, disconnect the tie rod end assembly LH from the steering relay rod assembly.
45450
31.DISCONNECT STEERING RELAY ROD ASSEMBLY
| *a | for Idler Arm Bracket Assembly Side |
| *b | for Center Arm Bracket Assembly Side |
Remove the 2 cotter pins.
Remove the 2 nuts.
Using SST, disconnect the steering relay rod assembly from the center arm bracket assembly and idler arm bracket assembly.
51202D
32.REMOVE FRONT LOWER SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 6 bolts, 4 nuts, 4 washers and front lower suspension crossmember sub-assembly.
While fixing the nut in place, loosen and remove the through bolt.
33110
33.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
35000
34.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
31210
35.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)
31250
36.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)
82121
37.DISCONNECT ENGINE WIRE
Remove the 2 bolts and disconnect the engine wire from the No. 1 engine hanger.
| *a | LH Side |
| *b | RH Side |
Remove the 2 bolts and nut, and disconnect the engine wire from the engine assembly.
87246B
38.DISCONNECT OUTLET HEATER WATER HOSE B
Slide the clamp and disconnect the outlet heater water hose B.
87245B
39.DISCONNECT INLET HEATER WATER HOSE B
Slide the clamp and disconnect the inlet heater water hose B.
88320
40.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Disconnect the connector.
Remove the 4 bolts and disconnect the cooler compressor assembly.
44774
41.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Slide the clamp and disconnect the union to connector tube hose.
23271F
42.DISCONNECT FUEL HOSE
Slide the 2 clamps and disconnect the 2 fuel hoses.
87207J
43.DISCONNECT NO. 1 WATER PIPE AND HOSE SUB-ASSEMBLY
| *A | for Manual Transmission |
| *B | for Automatic Transmission |
Remove the 6 bolts and disconnect the No. 1 water pipe and hose sub-assembly.
11000
44.REMOVE ENGINE ASSEMBLY
Using an engine lifter, support the engine assembly and height adjustments or plate lift attachments.
Place the height adjustments or plate lift attachments so that the engine assembly is level.
As the engine assembly is very heavy, be sure to support it securely.
Remove the 2 nuts and washer.
Remove the 4 bolts and front No. 1 engine mounting bracket LH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the 2 nuts and washer.
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the engine assembly.
When removing the engine assembly be careful not to damage any wire harnesses.
45.INSTALL ENGINE STAND
Attach an engine sling device and hang the engine assembly with a chain block.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Install the engine assembly to an engine stand with bolts.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
Remove the 2 bolts and generator bracket.
Remove the 2 bolts and No. 1 engine hanger.
12180E
46.REMOVE OIL FILLER CAP ASSEMBLY
Remove the oil filler cap sub-assembly.
12601B
47.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Remove the 2 bolts and No. 1 engine cover sub-assembly.
11202D
48.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the bolt and disconnect the 4 connectors and remove the wire harness.
Disconnect the PCV hose and, remove the 6 bolts and oil separator assembly.
Remove the 2 bolts, 2 cylinder head cover stay and 2 cylinder head cushion.
Remove the No. 2 cylinder head cover sub-assembly and cylinder head cover gasket.
Remove the 4 No. 2 cylinder head cover gaskets.
25620
49.REMOVE EGR VALVE ASSEMBLY
26100
50.REMOVE DIESEL THROTTLE BODY
23741B
51.REMOVE INJECTION PIPE CLAMP
52.REMOVE INJECTION PIPE SUB-ASSEMBLY
23670
53.REMOVE INJECTOR ASSEMBLY
16577C
54.REMOVE RADIATOR PIPE
Remove the 2 bolts and radiator pipe.
Remove the gasket.
44310
55.REMOVE VANE PUMP ASSEMBLY
Remove the 2 bolts and remove the vane pump assembly.
Remove the O-ring.
17201
56.REMOVE TURBOCHARGER SUB-ASSEMBLY
83420
57.REMOVE WATER TEMPERATURE SENDER GAUGE ASSEMBLY
11301K
58.REMOVE CRANKSHAFT POSITION SENSOR
11301M
59.REMOVE CAMSHAFT POSITION SENSOR
16630G
60.REMOVE IDLER PULLEY ASSEMBLY
Remove the 2 bolts and idler pulley assembly.
88440B
61.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET
Remove the 3 bolts and idle pulley assembly with bracket.
88431A
62.REMOVE NO. 2 COMPRESSOR MOUNTING BRACKET
Remove the 5 bolts and No. 2 compressor mounting bracket.
88431
63.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 2 bolts and No. 1 compressor mounting bracket.
16331A
64.REMOVE THERMOSTAT
16333
65.REMOVE WATER OUTLET HOUSING
Remove the 3 bolts and water outlet housing.
Remove the gasket.
87208L
66.REMOVE WATER PIPE SUB-ASSEMBLY
Remove the 3 bolts, water pipe sub-assembly and O-ring.
67.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the connector.
Slide the clamp and disconnect the water hose.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly.
16206
68.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 8 bolts and water by-pass pipe sub-assembly.
Remove the 2 gaskets and 3 O-rings.
16100
69.REMOVE ENGINE WATER PUMP ASSEMBLY
23810A
70.REMOVE COMMON RAIL ASSEMBLY
22214B
71.REMOVE FUEL ADDITION CUT VALVE ASSEMBLY
22100
72.REMOVE FUEL SUPPLY PUMP ASSEMBLY
73.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Remove the nut and the fuel pipe clamp.
Remove the 2 union bolts, 2 gaskets and No. 3 nozzle leakage pipe sub-assembly.
89458G
74.INSTALL NO. 2 FUEL PRESSURE SENSOR
23300D
75.REMOVE DIESEL FUEL FILTER ASSEMBLY
23803H
76.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
Remove the union bolt, 2 gaskets and fuel return pipe sub-assembly.
23310
77.REMOVE UPPER FUEL FILTER BODY
Remove the 2 bolts and upper fuel filter body.
19971E
78.REMOVE VACUUM PIPE
Remove the nut and pipe clamp.
Remove the union bolt, vacuum pipe and 2 gaskets.
29601B
79.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY
Remove the 3 union bolts and vacuum pump oil pipe sub-assembly and 3 gaskets.
29300
80.REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump assembly and O-ring.
23849G
81.REMOVE FUEL PIPE SUPPORT
Remove the bolt and fuel pipe support.
23264D
82.REMOVE FUEL FILTER BRACKET
Remove the 2 bolts and fuel filter bracket.
83.REMOVE OIL COOLER COVER SUB-ASSEMBLY
12204
84.REMOVE VENTILATION VALVE SUB-ASSEMBLY
Slide the clamp and disconnect the hose.
Remove the bolt and ventilation valve sub-assembly.
16206A
85.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 5 bolts and No. 2 water by-pass pipe sub-assembly.
Remove the 3 O-rings.
17107
86.REMOVE EXHAUST MANIFOLD HEAT INSULATOR SUB-ASSEMBLY
17141
87.REMOVE EXHAUST MANIFOLD
17111
88.REMOVE INTAKE MANIFOLD
23809L
89.REMOVE FUEL PIPE SUPPORT SUB-ASSEMBLY
Remove the 2 bolts and fuel pipe support sub-assembly.
23849G
90.REMOVE FUEL PIPE SUPPORT
Remove the 2 bolts and fuel pipe support.