1. PRECAUTION
Be sure to read "PRECAUTION" thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION)
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.DRAIN BRAKE FLUID
85192
4.REMOVE FRONT WIPER ARM HEAD CAP
5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
6.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
53867H
7.REMOVE FRONT FENDER TO COWL SIDE SEAL LH
53866J
8.REMOVE FRONT FENDER TO COWL SIDE SEAL RH
55781F
9.REMOVE COWL TOP VENTILATOR LOUVER
10.SEPARATE BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET
11.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR LINK
12.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
13.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
53292A
14.REMOVE UPPER RADIATOR SUPPORT SEAL (for RHD)
11209
15.REMOVE V-BANK COVER SUB-ASSEMBLY (for RHD)
51442
16.REMOVE NO. 2 ENGINE UNDER COVER (for RHD)
17.DRAIN ENGINE COOLANT (for RHD)
16470
18.SEPARATE RADIATOR RESERVOIR TANK ASSEMBLY (for RHD)
17190
19.REMOVE INTAKE AIR SURGE TANK ASSEMBLY (for RHD)
55420A
20.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY
55660
21.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
55042B
22.REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
55447C
23.REMOVE NO. 1 SWITCH HOLE BASE
55606
24.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55432B
25.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)
55432B
26.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Driver Side Knee Airbag)
73900
27.REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
47201
28.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (for LHD)
47201
29.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (for RHD)
30.DISCONNECT VACUUM HOSE
Move the clip and disconnect the vacuum hose.
47264A
31.REMOVE PUSH ROD PIN
Remove the clip from the push rod pin.
Remove the push rod pin from the push rod clevis.
47264D
32.REMOVE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
Loosen the push rod clevis lock nut.
Remove the push rod clevis.
33.SEPARATE BRAKE LINE (for LHD)
Using a union nut wrench, disconnect the 6 brake lines from the brake actuator.
Using a union nut wrench, disconnect the 4 brake lines.
Disengage the 5 clamps.
Remove the bolt and separate the brake lines from the body.
34.SEPARATE BRAKE LINE (for RHD)
Disengage the 4 clamps and separate the 2 brake lines.
35.SEPARATE WIRE HARNESS (for LHD)
Remove the nut and 2 bolts, and separate the wire harness from the body.
36.SEPARATE WIRE HARNESS (for RHD)
Remove the bolt and separate the wire harness.
Disconnect the 3 connectors.
11101J
37.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for RHD)
Remove the bolt and camshaft timing oil control valve assembly.
44610
38.REMOVE BRAKE BOOSTER ASSEMBLY
Remove the 4 nuts and brake booster assembly.
44785
39.REMOVE BRAKE BOOSTER GASKET
44730
40.REMOVE BRAKE VACUUM CHECK VALVE ASSEMBLY
44696
41.REMOVE CHECK VALVE GROMMET