Home › Drivetrain › AXLE › FRONT AXLE HUB › 2014.09–2016.05
RM24M0E _52 Drivetrain _059581 AXLE _0292138 FRONT AXLE HUB A

AXLE  FRONT AXLE HUB  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 43502C 1.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

C136803

a.

Install the dust cover to the steering knuckle.


b.

Install the axle hub with the 4 bolts.

Torque:
96 N*m (979 kgf*cm, 71 ft.*lbf)

NOTICE:

Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.



Hide 43340A 2.INSTALL FRONT LOWER BALL JOINT ASSEMBLY LH

Hide 3.INSTALL STEERING KNUCKLE WITH AXLE HUB

a.

Align the shaft splines and drive in the drive shaft.


b.

Install the steering knuckle with axle hub with the 2 bolts and 2 nuts.

T = 240 N*m{ 2,447 kgf*cm 177 ft.*lbf }

NOTICE:

Do not tighten the bolts.



Hide 48069 4.CONNECT FRONT SUSPENSION LOWER NO. 1 ARM SUB-ASSEMBLY LH

a.
C136800

Connect the lower arm to the ball joint with the bolt and 2nuts.

Torque:
93 N*m (948 kgf*cm, 69 ft.*lbf)


Hide 45046 5.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 7.CHECK FRONT AXLE HUB BEARING

a.

Check the axle hub bearing (see page Drivetrain>AXLE>FRONT AXLE HUB>ON-VEHICLE INSPECTION).


Hide 47750 9.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH

a.
C130484

Install the caliper with 2 bolts.

Torque:
98 N*m (999 kgf*cm, 72 ft.*lbf)


Hide 43502H 10.INSTALL FRONT AXLE HUB NUT (for 2AZ-FE)

a.

Clean the threaded parts on the front drive shaft assembly and a new axle hub nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Install the axle hub nut.

T = 216 N*m{ 2,203 kgf*cm 159 ft.*lbf }


c.
C136797

Using a chisel and hammer, stake the axle hub nut.


Hide 43502H 11.INSTALL FRONT AXLE HUB NUT (for 2GR-FE)

a.

Clean the threaded parts on the front drive shaft assembly and a new axle hub nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.

Install the axle hub nut.

T = 292 N*m{ 2,976 kgf*cm 215 ft.*lbf }


c.
C136797

Using a chisel and hammer, stake the axle hub nut.


Hide 12.ADD AUTOMATIC TRANSAXLE FLUID (for 2AZ-FE, Automatic Transaxle)

Hide 13.ADD AUTOMATIC TRANSAXLE FLUID (for 2GR-FE)

Hide 14.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 15.CHECK FOR AUTOMATIC TRANSAXLE FLUID LEAKAGE

Hide 16.INSTALL FRONT WHEEL

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }

Hide 17.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

a.

Inspect and adjust the wheel alignment (see page Suspension>SUSPENSION>FRONT WHEEL ALIGNMENT>ADJUSTMENT).


Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See Page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 19.CHECK SPEED SENSOR SIGNAL