Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1441  Performance Decline of Brake Function  


DESCRIPTION

The skid control ECU (brake actuator assembly) judges brake failure conditions have occurred based on signals from the brake pedal load sensing switch and master cylinder pressure sensor.

NOTICE:

Do not intentionally stop the engine when driving. Even when no malfunction has occurred in the brake system, DTC C1441 will be stored when it is judged that a failure has occurred in the brake system due to a reduction in vacuum.


DTCs may be stored if one of the following occurs:

·

The brake pedal load sensing switch is malfunctioning (deviation in characteristics).

·

The brake pedal is depressed when moving the vehicle with the engine not running and the engine switch on (IG).

·

Bleeding is performed with the engine running or the engine switch on (IG).

·

The accelerator and brake pedals depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1441 Performance Decline of Brake Function When the brake pedal load sensing switch and master cylinder pressure sensor are functioning normally and the brake pedal load sensing switch is judged as on, the pressure signal from the master cylinder pressure sensor does not indicate an increase.
·

Brake pedal load sensing switch (brake pedal support assembly)

·

Brake booster assembly

·

Skid control ECU (brake actuator assembly)

·

Brake fluid leaks



CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK ACCELERATOR PEDAL AND BRAKE PEDAL OPERATION
a.

Interview the customer to check if the pedals were depressed simultaneously while driving or braking.

OK:

The pedals were not depressed simultaneously.


HINT:

The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.




OK

2.CHECK DTC AND FREEZE FRAME DATA

NG

END

2.CHECK DTC AND FREEZE FRAME DATA
a.

Check and record DTCs and Freeze Frame Data (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR for Check DTCs and Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATA for Freeze Frame Data).

HINT:
·

Read Freeze Frame Data at the time DTC C1441 was stored, go to operation history and confirm the operating conditions.

·

When reading Freeze Frame Data to confirm operating conditions, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".





NEXT

3.CLEAR DTC
3.CLEAR DTC

NEXT

4.CHECK BRAKE PEDAL OPERATION
4.CHECK BRAKE PEDAL OPERATION
a.

Based on the customer problem analysis, confirm the brake pedal condition at the time the brake pedal was operated.

Result:
Result Proceed to
The brake pedal is hard to depress. A
The brake pedal is extremely easy to depress. B
Neither of the above conditions. (Problem symptom does not occur.) C




A

5.CHECK BRAKE BOOSTER ASSEMBLY

B

6.INSPECT BRAKE SYSTEM (OTHER)

C

10.RECONFIRM DTC
5.CHECK BRAKE BOOSTER ASSEMBLY
a.

Check the brake booster assembly (See page Brake>BRAKE>BRAKE BOOSTER(for 2AZ-FE LHD)>ON-VEHICLE INSPECTION for 2AZ-FE LHD, Brake>BRAKE>BRAKE BOOSTER(for 2AZ-FE RHD)>ON-VEHICLE INSPECTION for 2AZ-FE RHD, or Brake>BRAKE>BRAKE BOOSTER(for 2GR-FE)>ON-VEHICLE INSPECTION for 2GR-FE).

Result:
Result Proceed to
The brake booster assembly is abnormal. A
The brake booster assembly is normal. B


HINT:

If the result shows that the brake booster assembly is defective, check the related components such as the brake booster, brake vacuum check valve, check valve grommet, brake booster gasket, vacuum hose and intake system for vacuum leaks or clogs.




A

INSPECT RELATED COMPONENTS (FOR VACUUM LEAKS OR CLOGS)

B

10.RECONFIRM DTC
6.INSPECT BRAKE SYSTEM (OTHER)
a.

Brake pedal inspection

i.

Perform a visual inspection and operate the brake pedal to check for any malfunctions.


ii.

Check the brake pedal height, brake pedal free play and brake pedal reserve distance.

Click hereBrake>BRAKE>BRAKE PEDAL>ADJUSTMENT

HINT:

If the brake pedal height is not within specification, confirm that there are no other malfunctions before adjusting the brake pedal height.




b.

Brake inspection

i.

Check that the disc brake pads of each wheel are installed correctly.


ii.

Check that the bleeder plug and union bolt is not loose, and that there are no damaged gaskets or brake fluid leaks, for each wheel cylinder.



c.

Brake fluid leaks and air in brake line inspection

i.

Check and take a note of the fluid level in the brake master cylinder reservoir sub-assembly.


ii.

Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).


iii.

Check if the brake fluid level in the brake master cylinder reservoir sub-assembly has changed.


iv.

If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder sub-assembly seals, etc.



d.

Bleeding air from brake system

i.

Bleed air from the brake lines and brake actuator assembly.

Click hereBrake>BRAKE>BRAKE FLUID>BLEEDING



Result:
Proceed to
NEXT



NEXT

7.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
7.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Active Test using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operating sound of motor can be heard


d.

Fully depress and hold the brake pedal.

HINT:

Make sure that the brake pedal has travelled excessively before holding it depressed.



e.

Operate the ABS motor relay using the Active Test and check if the brake pedal height changes when the pump motor is operating.

OK:

The brake pedal height does not change (the brake pedal travel remains excessive).


Result:
Proceed to
OK
NG




OK

8.CHECK BRAKE MASTER CYLINDER SUB-ASSEMBLY

NG

8.CHECK BRAKE MASTER CYLINDER SUB-ASSEMBLY
a.

Check that there are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.

OK:

There are no brake fluid leaks and no indications of a malfunction in the brake master cylinder sub-assembly.



Result:
Proceed to
OK
NG



OK

9.INSPECT BRAKE BOOSTER ASSEMBLY

NG

REPLACE BRAKE MASTER CYLINDER SUB-ASSEMBLY

9.INSPECT BRAKE BOOSTER ASSEMBLY
a.

Inspect operation of the brake booster assembly.

for 2AZ-FE LHD: Click hereBrake>BRAKE>BRAKE BOOSTER(for 2AZ-FE LHD)>ON-VEHICLE INSPECTION

for 2AZ-FE RHD: Click hereBrake>BRAKE>BRAKE BOOSTER(for 2AZ-FE RHD)>ON-VEHICLE INSPECTION

for 2GR-FE: Click hereBrake>BRAKE>BRAKE BOOSTER(for 2GR-FE)>ON-VEHICLE INSPECTION

OK:

The brake booster assembly is normal.



Result:
Proceed to
OK
NG



OK

10.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER ASSEMBLY

10.RECONFIRM DTC

b.

Start the engine.


c.

Perform a road test.

NOTICE:

Do not intentionally stop the engine when driving. DTC C1441 will be stored if the brake pedal is depressed when moving the vehicle with the engine not running and the engine switch on (IG).



d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1441 is not output. A
DTCs C1441 and other DTC are output. B
Only DTC C1441 is output. C


HINT:
·

If DTC C1441 and other DTCs are output simultaneously, the other DTCs may have caused the engine to malfunction, resulting in DTC C1441 to be output. Read Freeze Frame Data to confirm malfunctioning parts and repair the applicable part.

·

When reading Freeze Frame Data to confirm malfunctioning parts, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".



Result:
Proceed to
OK
NG




A

END

B

CHECK AND REPAIR APPLICABLE PART

C

11.CHECK BRAKE PEDAL SUPPORT ASSEMBLY
11.CHECK BRAKE PEDAL SUPPORT ASSEMBLY
a.

Check that the match marks on the adjustment part of the brake pedal load sensing switch are aligned with the match marks on the brackets, nuts, adjusting screw, etc.

C267847E04
2.344,2.333 2.802,3.156 true 1.292,1.927 0.875,2.833 true 2.271,1.896 2.865,1.292 2.865,1.292 2.938,1.292 false 4.896,2.333 5.354,3.219 true 5.948,1.927 6.365,2.677 true 4.979,1.833 4.26,2.375 4.26,2.375 4.177,2.375 false 1.615,1.573 2.188,0.771 2.188,0.771 2.01,1.5 true 5.625,1.573 5.052,0.771 5.052,0.771 5.229,1.5 true 2.979,1.208 4.135,1.542 1.156,0.333 10 false *1 2.781,3.167 3.594,3.344 0.813,0.177 10 false *a 0.271,0.177 1,0.385 0.729,0.208 12 false *A 3.583,0.198 4.313,0.406 0.729,0.208 12 false *B 0.792,2.833 1.604,3.01 0.813,0.177 10 false *a 2.198,0.635 3.01,0.813 0.813,0.177 10 false *a 5.313,3.25 6.125,3.427 0.813,0.177 10 false *a 6.344,2.698 6.615,2.875 0.271,0.177 10 false *a 4.917,0.594 5.698,0.771 0.781,0.177 10 false *a 4.01,2.302 5.167,2.635 1.156,0.333 10 false *1

Text in Illustration
*A for LHD *B for RHD
*1 Brake Pedal Load Sensing Switch - -
*a Match Mark - -

OK:

The match marks on the adjustment part of the brake pedal load sensing switch are aligned with the match marks on the brackets, nuts, adjusting screw, etc.




OK

NG

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY