The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from each speed sensor.
These signals are used for recognizing that all four wheels are operating properly.
Therefore, signals from all wheels must be equal.
DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1237 | Speed Sensor Rotor Faulty | Any of the following is detected:
1.
Discrepancy among four wheel speed sensor output. 2.
Abnormal pulse signals from 3 or more sensors. 3.
Continuous ABS control is performed for 60 seconds or more. 4.
VSC control is performed for 5 seconds or more. |
·
Tire and wheel size ·
Tire deformation ·
Speed sensor rotor ·
Speed sensor ·
Speed sensor circuit ·
Skid control ECU (brake actuator assembly) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor rotor RH (front axle hub sub-assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor rotor LH (front axle hub sub-assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
DTC C1275 is for the front speed sensor RH.
DTC C1276 is for the front speed sensor LH.
DTC C1277 is for the rear speed sensor RH.
DTC C1278 is for the rear speed sensor LH.
Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271 for front, and Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273 for rear).
When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271 for C1330, C1331, C1464 and C1465, and Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273 for C1332, C1333, C1466 and C1467).
Check the size and condition of all four tires (See page Drivetrain>TIRE AND WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).
The DTC is output when tire deformation or a difference in tire size is detected.
The diameter of all four tires and the tire pressure are the same.
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
Check the speed value output from the speed sensor displayed on the GTS.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
A
B
C
Turn the engine switch off.
Perform the sensor check using Test Mode Procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
All Test Mode DTCs are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
A
B
C
Turn the engine switch off.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is not output. | A |
| DTC C1237 is output (for front). | B |
| DTC C1237 is output (for rear). | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Remove the front speed sensor and the component with the sensor rotor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL for speed sensor, and Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL for sensor rotor).
Check the speed sensor tip and speed sensor rotor.
No scratches, oil, or foreign matter on the sensor tip and rotor.
If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.
Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
OK
NG
Install the front speed sensor and the component with the sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-16 (FR+) - A20-2 (FR+) | Always | Below 1 Ω |
| A35-16 (FR+) or A20-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| A35-4 (FR-) - A20-1 (FR-) | Always | Below 1 Ω |
| A35-4 (FR-) or A20-1 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-19 (FL+) - A5-2 (FL+) | Always | Below 1 Ω |
| A35-19 (FL+) or A5-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| A35-8 (FL-) - A5-1 (FL-) | Always | Below 1 Ω |
| A35-8 (FL-) or A5-1 (FL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the A35 skid control ECU (brake actuator assembly) connector and A5 or A20 front speed sensor connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the engine switch off.
Replace the front speed sensor (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL).
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
Turn the engine switch off.
Replace the front speed sensor rotor (front axle hub sub-assembly) (See page Drivetrain>AXLE>FRONT AXLE HUB>REMOVAL).
The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c1-2 (RR+) - cN1-1 (RR+) | Always | Below 1 Ω |
| c1-2 (RR+) - cN1-2 (RR-) | Always | 10 kΩ or higher |
| c1-2 (RR+) or cN1-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| c1-1 (RR-) - cN1-2 (RR-) | Always | Below 1 Ω |
| c1-1 (RR-) - cN1-1 (RR+) | Always | 10 kΩ or higher |
| c1-1 (RR-) or cN1-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| d1-2 (RL+) - dM1-1 (RL+) | Always | Below 1 Ω |
| d1-2 (RL+) - dM1-2 (RL-) | Always | 10 kΩ or higher |
| d1-2 (RL+) or dM1-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| d1-1 (RL-) - dM1-2 (RL-) | Always | Below 1 Ω |
| d1-1 (RL-) - dM1-1 (RL+) | Always | 10 kΩ or higher |
| d1-1 (RL-) or dM1-2 (RL-) - Body ground | Always | 10 kΩ or higher |
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A35 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-17 (RR+) - cN1-1 (RR+) | Always | Below 1 Ω |
| A35-17 (RR+) or cN1-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| A35-29 (RR-) - cN1-2 (RR-) | Always | Below 1 Ω |
| A35-29 (RR-) or cN1-2 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A35-31 (RL+) - dM1-1 (RL+) | Always | Below 1 Ω |
| A35-31 (RL+) or dM1-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| A35-18 (RL-) - dM1-2 (RL-) | Always | Below 1 Ω |
| A35-18 (RL-) or dM1-2 (RL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Install the skid control sensor wire.
Reconnect the A35 skid control ECU (brake actuator assembly) connector.
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Turn the engine switch off.
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly) (See page Drivetrain>AXLE>REAR AXLE HUB>REMOVAL).
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).
NEXT
Clear the DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B