Home › BRAKE › BRAKE CONTROL › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    C1235/35    Foreign Object is Attached on Tip of Front Speed Sensor RH

DTC    C1236/36    Foreign Object is Attached on Tip of Front Speed Sensor LH

DTC    C1238/38    Foreign Object is Attached on Tip of Rear Speed Sensor RH

DTC    C1239/39    Foreign Object is Attached on Tip of Rear Speed Sensor LH

DTC    C1275/75    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276/76    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1277/77    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278/78    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.
Speed sensor rotors have 48 serrations. The hall IC type speed sensor use the frequency of output pulses to detect the vehicle speed. Because the sensor outputs digital pulses, it can detect vehicle speeds even when the vehicle is nearly stationary.
When foreign matter adheres to the speed sensor tip or speed sensor rotor, or the rotor teeth are chipped, these DTCs are output. An abnormal waveform input from the sensor determines these conditions.
These DTCs may be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.
DTCs C1275/75 to C1278/78 will be deleted when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275/75 to C1278/78 are output only in Test Mode.

C172023E03


DTC Code
INF Code
DTC Detection Condition
Trouble Area
C1235/35
302
Pulse waveform of speed sensor signal is abnormal for at least 5 seconds when vehicle speed is 20 km/h (12 mph) or more.
  1. Front speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
C1236/36
303
Pulse waveform of speed sensor signal is abnormal for at least 5 seconds when vehicle speed is 20 km/h (12 mph) or more.
  1. Front speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
C1238/38
304
Pulse waveform of speed sensor signal is abnormal for at least 5 seconds when vehicle speed is 20 km/h (12 mph) or more.
  1. Rear speed sensor RH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
C1239/39
305
Pulse waveform of speed sensor signal is abnormal for at least 5 seconds when vehicle speed is 20 km/h (12 mph) or more.
  1. Rear speed sensor LH
  2. Speed sensor circuit
  3. Sensor installation
  4. Speed sensor rotor
  5. Skid control ECU
C1275/75
C1276/76
C1277/77
C1278/78
-
Detected only during Test Mode.
Speed sensor rotor

HINT:
  1. DTCs C1235/35 and C1275/75 are for the front speed sensor RH.
  2. DTCs C1236/36 and C1276/76 are for the front speed sensor LH.
  3. DTCs C1238/38 and C1277/77 are for the rear speed sensor RH.
  4. DTCs C1239/39 and C1278/78 are for the rear speed sensor LH.


WIRING DIAGRAM


C173854E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization and calibration of the linear solenoid valve (Click here).

HINT:
When C0200/31, C0205/32, C0210/33, and/or C0215/34 are output together with C1235/35, C1236/36, C1238/38, and/or C1239/39, inspect and repair the trouble areas indicated by C0200/31, C0205/32, C0210/33, and/or C0215/34 first (Click here for front, or Click here for rear).

1.CHECK SPEED SENSOR AND SPEED SENSOR ROTOR SERRATIONS


    C175126E03
  1. Connect the oscilloscope to each speed sensor terminal of the skid control ECU.

  1. Check that waveform output when the wheels are rotated.

    OK:
    The same waveform is output from all the sensors and there is no noise or interference in the waveform.

  1. Check that the waveform does not change while jiggling a connector or a wire harness.

    OK:
    The waveform does not change.

    HINT:
    1. As the vehicle speed (wheel revolution speed) increases, a cycle of the waveform narrows and the output voltage becomes greater.
    2. When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to speed sensor rotor scratches, looseness or foreign matter attached to it.



NG
Go to step 3
OK


2.RECONFIRM DTC
  1. Turn the power switch off.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and C1239/39) are not output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    B



B
REPLACE SKID CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)  

3.INSPECT SPEED SENSOR


    C181541E01
  1. Turn the power switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect each speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    2 (FR+) - Body ground
    Always
    10 kΩ or higher
    1 (FR-) - Body ground
    Always
    10 kΩ or higher
    1 (RR+) - Body ground
    Always
    10 kΩ or higher
    2 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    2 (FL+) - Body ground
    Always
    10 kΩ or higher
    1 (FL-) - Body ground
    Always
    10 kΩ or higher
    1 (RL+) - Body ground
    Always
    10 kΩ or higher
    2 (RL-) - Body ground
    Always
    10 kΩ or higher

    NOTICE:
    Check the speed sensor signal after replacement (Click here).



NG
REPLACE SPEED SENSOR
OK


4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SPEED SENSOR)
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.


C173856E01

  1. Disconnect the skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A46-22 (FR+) - A29-2 (FR+)
    Always
    Below 1 Ω
    A46-22 (FR+) - Body ground
    Always
    10 kΩ or higher
    A46-32 (FR-) - A29-1 (FR-)
    Always
    Below 1 Ω
    A46-32 (FR-) - Body ground
    Always
    10 kΩ or higher
    A47-31 (RR+) - N20-1 (RR+)
    Always
    Below 1 Ω
    A47-31 (RR+) - Body ground
    Always
    10 kΩ or higher
    A47-23 (RR-) - N20-2 (RR-)
    Always
    Below 1 Ω
    A47-23 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A45-22 (FL+) - A12-2 (FL+)
    Always
    Below 1 Ω
    A45-22 (FL+) - Body ground
    Always
    10 kΩ or higher
    A45-28 (FL-) - A12-1 (FL-)
    Always
    Below 1 Ω
    A45-28 (FL-) - Body ground
    Always
    10 kΩ or higher
    A44-27 (RL+) - O39-1 (RL+)
    Always
    Below 1 Ω
    A44-27 (RL+) - Body ground
    Always
    10 kΩ or higher
    A44-35 (RL-) - O39-2 (RL-)
    Always
    Below 1 Ω
    A44-35 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.RECONFIRM DTC
  1. Reconnect the skid control ECU connectors and the speed sensor connector.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and C1239/39) are not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


6.CHECK SPEED SENSOR TIP
  1. Turn the power switch off.

  1. Remove the front or rear speed sensor (Click here for front, or Click here for rear).

  1. Check the speed sensor tip.

    OK:
    The sensor tip is free of scratches, oil, and foreign matter.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE SPEED SENSOR
OK


7.CHECK SPEED SENSOR ROTOR
  1. Remove the front or rear speed sensor rotor (Click here for front, or Click here for rear).

  1. Check the speed sensor rotor.

    OK:
    The rotor is free of scratches, oil, missing teeth, and foreign matter.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).

    HINT:
    1. If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
    2. If the rear speed sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.



NG
CLEAN OR REPLACE SPEED SENSOR ROTOR
OK


8.RECONFIRM DTC
  1. Install the speed sensor and the speed sensor rotor.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and C1239/39) are not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)
A


9.REPLACE SPEED SENSOR
  1. Turn the power switch off.

  1. Replace the front speed sensor or the rear speed sensor (Click here for front, or Click here for rear).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


10.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and C1239/39) are not output
    B



B
END
A


11.REPLACE SPEED SENSOR ROTOR
  1. Turn the power switch off.

  1. Remove the front drive shaft assembly or the rear drive shaft assembly (Click here for front, or Click here for rear).

  1. Replace the front drive outboard joint shaft assembly (front speed sensor rotor) or the outboard joint shaft assembly (rear speed sensor rotor) (Click here for front, or Click here for rear).

    HINT:
    1. If the front speed sensor rotor needs to be replaced, replace it together with the front drive outboard joint shaft assembly.
    2. If the rear speed sensor rotor needs to be replaced, replace it together with the outboard joint shaft assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12.RECONFIRM DTC
  1. Install the drive shaft assembly.

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (READY).

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.

  1. Check if the same DTC is recorded (Click here).

    Result:

    Result
    Proceed to
    DTCs (C1235/35, C1236/36, C1238/38 and/or C1239/39) are output
    A
    DTCs (C1235/35, C1236/36, C1238/38 and C1239/39) are not output
    B



B
END
A

REPLACE SKID CONTROL ECU (Click here)