Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420083 CYLINDER HEAD GASKET A

2GR-FKS ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

*5: When the starter assembly is replaced, "ST relay" must be also replaced

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of fuel injector assembly (for port injection)

·

Replacement of fuel injector assembly (for direct injection)

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Air leaks from intake system

·

Gas leak from exhaust system is repaired

·

Replacement of knock control sensor


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UA80F Initialization:(Click here)
for UA80F Registration:(Click here)
Replacement of ECM
If transaxle compensation code read from ECM:
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


If transaxle compensation code not read from ECM:
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of starter assembly*5 Clear the number of starter operations Stop and Start System (Click here)
Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UA80E:(Click here)
for UA80F:(Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 1.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

Hide 89615 3.REMOVE KNOCK CONTROL SENSOR

Hide 29300 5.REMOVE VACUUM PUMP ASSEMBLY

Hide 16361A 6.REMOVE V-RIBBED BELT

Hide 27020 7.REMOVE GENERATOR ASSEMBLY

Hide 8.REMOVE COMPRESSOR AND MAGNETIC CLUTCH

Hide 16604 9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16173 11.REMOVE WATER PUMP PULLEY

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 12585 13.REMOVE NO. 5 CYLINDER BLOCK INSULATOR

Hide 14.REMOVE WIRE HARNESS CLAMP BRACKET

Hide 16522 15.REMOVE WATER FILLER BRACKET

Hide 12315 17.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

Hide 16261 18.DISCONNECT WATER BY-PASS HOSE

Hide 16031 19.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 15370B 20.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)

Hide 15370B 21.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)

Hide 15370C 22.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)

Hide 15370C 23.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)

Hide 24.REMOVE VVT SENSOR (for Intake Side of Bank 1)

Hide 25.REMOVE VVT SENSOR (for Exhaust Side of Bank 1)

Hide 26.REMOVE VVT SENSOR (for Intake Side of Bank 2)

Hide 27.REMOVE VVT SENSOR (for Exhaust Side of Bank 2)

Hide 19312 28.REMOVE CRANKSHAFT POSITION SENSOR PROTECTOR

Hide 11201 30.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 31.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11193 32.REMOVE SPARK PLUG TUBE GASKET

Hide 15710 33.REMOVE OIL COOLER ASSEMBLY

Hide 12102A 35.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 36.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 37.REMOVE OIL PAN SUB-ASSEMBLY

a.
A366043C03
2.552,1.99 2.958,2.177 0.406,0.188 10 true *a 2.333,0 2.667,0.198 0.333,0.198 10 true *a
*a Nut


Remove the 16 bolts and 2 nuts from the oil pan sub-assembly.

NOTICE:

Make sure to clean the bolts and stud bolts and check the threads for cracks or other damage.



b.
A366105C01
0.635,0.552 2.906,0.25 2.906,0.25 2.823,2.563 true 0.635,2.833 2.896,0.26 true 2.948,0.104 3.26,0.26 0.313,0.156 10 false *a
*a Protective Tape


Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and timing chain cover assembly or cylinder block sub-assembly with a screwdriver wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly, timing chain cover assembly and oil pan sub-assembly.



c.
A366106

Remove the 2 oil pan gaskets from the timing chain cover assembly.


Hide 11310 38.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 11301C 39.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 40.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 41.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 42.REMOVE CHAIN TENSIONER SLIPPER

Hide 13050 44.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

Hide 13550 45.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 46.REMOVE CAMSHAFT BEARING CAP (for Bank 1)

Hide 49.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 50.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY, CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

Hide 13560A 51.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 52.REMOVE CAMSHAFT BEARING CAP (for Bank 2)

Hide 13053 53.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY

Hide 13054 54.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 11104A 55.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13561 57.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 58.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13801 59.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 60.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 63.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 64.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11116 66.REMOVE NO. 2 CYLINDER HEAD GASKET

a.

Remove the No. 2 cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 67.INSPECT CYLINDER HEAD SET BOLT