Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2012.10
RM1840EF _51 Engine / Hybrid System _009576 2TR-FBE ENGINE MECHANICAL _0052199 ENGINE ASSEMBLY A

2TR-FBE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 5.REMOVE NO. 2 ENGINE UNDER COVER

Hide 9.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 10.REMOVE INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY

A239760

a.

Disconnect the vacuum hose.


b.

Disconnect the No. 2 PCV hose.


c.

Disconnect the mass air flow meter connector and detach the wire harness clamps.


d.

Loosen the hose clamp and remove the 4 bolts, air cleaner and intake air connector assembly.


Hide 13.DISCONNECT RADIATOR HOSE OUTLET

Hide 15.REMOVE AIR PUMP INLET

Hide 17.REMOVE FAN PULLEY

Hide 18.REMOVE OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 19.REMOVE OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 21.DISCONNECT HEATER WATER HOSE

a.
A250065

Disconnect the heater water inlet hose and heater water outlet hose from the heater pipe.


Hide 22.DISCONNECT HOSE

A239761

a.

Disconnect the vacuum hose (for the brake master cylinder).


b.

Disconnect the purge line hose.


Hide 26.REMOVE FUEL HOSE

a.
A239213

Disconnect the fuel hose.


Hide 27.DISCONNECT ENGINE WIRE

a.
A111959

Disconnect the ECM connectors from the cabin.

i.

Remove the glove compartment door.


ii.

Disconnect the 4 ECM connectors.



b.
A250527

Disconnect the air injection driver connector.


c.

Pull out the engine wire from the cabin.


d.

Disconnect the air fuel ratio sensor connector.


e.

Remove the bolt and disconnect the sensor bracket from the right side of the frame.


f.
A250528

Remove the bolt and disconnect the ground wire from the left side of the frame.


g.

Remove the nut and disconnect the ground wire from the body.


h.

Remove the engine room relay block cover (upper).


i.
A302608
2.802,1.135 3.115,1.292 0.313,0.156 10 false *a 2.552,1.875 2.865,2.031 0.313,0.156 10 false *a 0.417,1.063 0.729,1.219 0.313,0.156 10 false *a
*a Pull


Remove the engine room relay block cover (side).

i.

Using a screwdriver, detach the 4 claws and remove the relay block cover.

HINT:

Tape the screwdriver tip before use.




j.

Remove the nut and disconnect the cable from the engine room junction block.


k.

Disconnect the 2 engine room junction block connectors and wire clamp.


l.

Remove the bolt and disconnect the wire clamp from the front engine mounting bracket LH.


Hide 28.DISCONNECT VANE PUMP ASSEMBLY

a.

Disconnect the oil pressure switch connector.


b.
A099199

Remove the 2 bolts and disconnect the vane pump from the engine.


c.

Support the vane pump securely.


Hide 29.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 30.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the bolt, engine oil level dipstick guide and O-ring.

NOTICE:

Cover the dipstick guide hole to prevent foreign matter from entering it.



Hide 31.DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 32.REMOVE HOOD ASSEMBLY

A237711

a.

Disconnect the washer nozzle hose.


b.

Remove the 4 bolts and hood.

NOTICE:

Be careful not to damage the vehicle.



Hide 35.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

Hide 36.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

Hide 38.REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

Hide 41.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Remove the 4 bolts and rear No. 1 engine mounting insulator.


Hide 42.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 43.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 44.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 45.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 46.REMOVE REAR END PLATE

a.

Remove the bolt and disconnect the No. 1 water by-pass pipe from the rear end plate.


b.

Remove the bolt and rear end plate.


Hide 47.INSTALL ENGINE HANGER

a.
A099202
0.042,0.052 0.354,0.302 0.313,0.25 10 false *a 1.75,0.052 2.042,0.292 0.292,0.24 10 false *b
*a Rear Side
*b Front Side


Install 2 engine hangers with 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-0C010
Bolt 90105-T0129



Hide 48.REMOVE ENGINE ASSEMBLY

a.

Attach an engine sling device to the engine hangers.


b.
G037190

Remove the 4 bolts and 4 nuts holding the engine mounting brackets to the frame.


c.
A302609
1.24,0.552 1.24,0.479 false
V100135

Lift


Lift the engine out of the vehicle slowly and carefully.

NOTICE:

Make sure to disconnect all the wires, hoses and cables from the engine. Keep the disconnected wires, hoses and cables off of the engine.



Hide 49.INSTALL ENGINE TO ENGINE STAND

a.

Install the engine to an engine stand with bolts.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.




b.

Remove the 2 bolts and 2 engine hangers.