1.INSTALL ENGINE HANGER
2.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
3.INSTALL ENGINE ASSEMBLY
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
| *a | Front Engine Mounting Insulator
(LH Side) |
| *b | Claw (Stopper) |
|
Front |
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure to install the bolt with the claw (stopper) as shown in the illustration so that a clearance is maintained between the claw (stopper) and the intermediate shaft.
Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.
32101
4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
35000
5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
6.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
37100
7.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TASA Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
51569
8.INSTALL PROPELLER SHAFT GUARD
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TASA Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
41110F
9.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY
10.INSTALL POWER STEERING LINK ASSEMBLY
45219
11.CONNECT STEERING SLIDING YOKE
43410D
12.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
43420
13.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
43410
14.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
Use the same procedure described for the LH side.
48069
15.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
16.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
17.CONNECT TIE ROD END SUB-ASSEMBLY LH
18.CONNECT TIE ROD END SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
89543
19.CONNECT FRONT SPEED SENSOR LH
89542
20.CONNECT FRONT SPEED SENSOR RH
Use the same procedure described for the LH side.
43502H
21.INSTALL FRONT AXLE SHAFT NUT
43514C
22.INSTALL FRONT AXLE HUB GREASE CAP
37140
23.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
51561D
24.INSTALL PROPELLER SHAFT GUARD
for TASA Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TASA Made)>INSTALLATION
for TMMIN Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TMMIN Made)>INSTALLATION
23802B
25.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY
Connect the No. 2 fuel pipe sub-assembly, and slide the clamp to secure the hose.
23801P
26.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY
27.INSTALL WATER HOSE SUB-ASSEMBLY
Install the water hose sub-assembly, and slide the 4 clamps to secure the hose.
88320
28.CONNECT COOLER COMPRESSOR ASSEMBLY
27020
29.INSTALL GENERATOR ASSEMBLY
82121
30.CONNECT ENGINE WIRE
Connect the 2 connectors to the engine room relay block.
Connect the engine wire to the engine room relay block with the nut.
Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.
Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.
Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.
Install the battery tray.
Install the battery.
Install the battery hold down clamp with the 2 nuts.
Tighten the nut and install the positive (+) battery terminal.
Position the positive (+) battery terminal as shown in the illustration.
Connect the engine room main wire to the battery positive cable with the nut.
Push the engine wire through the dash panel into the cabin.
The wire should be within the range shown in the illustration.
Connect the engine wire and attach the clamp to the bracket.
Connect the engine wire with the bolt.
Connect the connector.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
89661
31.INSTALL ECM
55550
32.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
55607
33.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
11363A
34.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
35.INSTALL STARTER ASSEMBLY
17105
36.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
17119
37.INSTALL NO. 2 MANIFOLD STAY
17104
38.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
17118
39.INSTALL MANIFOLD STAY
17410
40.INSTALL FRONT EXHAUST PIPE ASSEMBLY
17450B
41.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY
17129
42.INSTALL INTAKE AIR SURGE TANK
44320
43.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly with the 2 bolts.
Do not hit other parts with the pulley when installing the vane pump.
Connect the connector.
16400
44.INSTALL RADIATOR ASSEMBLY
32941
45.CONNECT NO. 1 OIL COOLER INLET HOSE
32942
46.CONNECT NO. 1 OIL COOLER OUTLET HOSE
16711
47.INSTALL FAN SHROUD
16470
48.INSTALL RADIATOR RESERVOIR
16571
49.INSTALL RADIATOR HOSE INLET
16572
50.INSTALL RADIATOR HOSE OUTLET
16593
51.INSTALL NO. 1 RADIATOR AIR GUIDE
17700
52.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Connect the 3 clamps to the air cleaner case sub-assembly.
17801
53.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17705
54.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
53294C
55.INSTALL RADIATOR SIDE DEFLECTOR LH
53293C
56.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
53735B
57.INSTALL FRONT UPPER FENDER APRON SEAL LH
Install the front upper fender apron seal LH with 6 new clips.
53735B
58.INSTALL FRONT UPPER FENDER APRON SEAL RH
Install the front upper fender apron seal RH with 6 new clips.
53882F
59.INSTALL FRONT FENDER SEAL LH
Install the front fender seal LH with 6 new clips.
53882F
60.INSTALL FRONT FENDER SEAL RH
Install the front fender seal RH with 6 new clips.
61.ADD DIFFERENTIAL OIL
51407A
62.INSTALL NO. 3 ENGINE UNDER COVER SUB-ASSEMBLY
51442
63.INSTALL NO. 2 ENGINE UNDER COVER
51410
64.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
53301
65.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose.
Adjust the hood sub-assembly.
66.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67.ADD ENGINE OIL
68.ADD ENGINE COOLANT
69.INSPECT FOR COOLANT LEAK
70.INSPECT FOR FUEL LEAK
71.INSPECT FOR OIL LEAK
72.INSPECT FOR EXHAUST GAS LEAK
73.INSPECT IGNITION TIMING
74.INSPECT ENGINE IDLE SPEED
75.INSPECT CO/HC
11259
76.INSTALL V-BANK COVER