Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2016.01
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0184011 ENGINE ASSEMBLY A

1TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 2.INSTALL FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.

Install the 2 front engine mounting insulator to the 2 front No. 1 engine mounting brackets with the 2 nuts.

Torque:
58 N*m (591 kgf*cm, 43 ft.*lbf)


Hide 12391 3.INSTALL FRONT ENGINE MOUNTING HEAT INSULATOR RH

a.

Install the front engine mounting heat insulator RH to the front engine mounting insulator with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 82121 4.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 11000 5.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Remove the engine assembly from the engine stand.


Hide 11000 6.INSTALL ENGINE ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Slowly lower the engine assembly into the engine compartment.


b.

Install the engine assembly to the body with the 4 bolts and 4 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:
A358251C01
3.083,1.667 3.083,1.5 3.083,1.5 2.917,1.292 false 1.875,1.188 2.188,1.344 0.313,0.156 10 false *a 3.021,1.667 3.25,1.854 0.229,0.188 10 false *b
*a Front Engine Mounting Insulator
(LH Side)
*b Claw (Stopper)
V100135

Front


·

Make sure to tighten the side with the nut.

·

When installing a bolt with a claw (stopper), make sure to install the bolt with the claw (stopper) as shown in the illustration so that a clearance is maintained between the claw (stopper) and the intermediate shaft.




c.

Remove the 2 bolts and 2 engine hangers.


Hide 11355 7.INSTALL REAR END PLATE

a.

Install the rear end plate to the cylinder block with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 10.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 33030 12.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 37100 13.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17410 15.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 16.CONNECT ENGINE WIRE

a.

Connect the sensor bracket to the right side of the frame with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Connect the air fuel ratio sensor connector.


c.

Connect the wire clamp to the front engine mounting bracket LH with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Connect the 2 connectors to the engine room relay block.


e.

Attach the clamp.


f.

Connect the engine wire to the engine room relay block with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


g.

Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.


h.

Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.


i.
A353224N01
1.667,1.25 1.917,1.417 0.25,0.167 10 true 45° 1.667,1.75 1.917,1.917 0.25,0.167 10 true 45°

Attach the clamp and install the No. 2 engine wire with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

HINT:

Position the No. 2 engine wire as shown in the illustration.



j.

Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


k.

Install the battery tray.


l.

Install the battery.


m.

Install the battery hold down clamp with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


n.
A348574N01
1.708,0.01 1.917,0.198 0.208,0.188 10 true 8° 1.417,0.01 1.625,0.198 0.208,0.188 10 true 8°

Tighten the nut and install the positive (+) battery terminal.

Torque:
5.35 N*m (55 kgf*cm, 47 in.*lbf)

HINT:

Position the positive (+) battery terminal as shown in the illustration.



o.

Connect the engine room main wire to the positive (+) battery terminal with the nut.

Torque:
7.55 N*m (77 kgf*cm, 67 in.*lbf)


p.

Connect the connector to the engine room main wire.


q.
A355823N01
0.51,0.156 0.969,0.354 0.458,0.198 10 false 45° 0.979,0.156 1.438,0.354 0.458,0.198 10 false 45°

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.



r.

Connect the engine wire with the bolt.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


s.

Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.


Hide 55550 18.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 23271H 19.CONNECT NO. 1 FUEL HOSE

Hide 23273C 20.CONNECT NO. 2 FUEL HOSE

Hide 44774 21.CONNECT UNION TO CONNECTOR TUBE HOSE

a.

Connect the union to connector tube hose to the intake manifold, and slide the clip to secure the hose.


Hide 22.CONNECT PURGE LINE HOSE

a.

Connect the purge line hose to the purge VSV, and slide the clip to secure the hose.


Hide 88320 24.CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 11452 25.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 15301 26.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 44320 27.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the power steering oil pressure switch connector.


Hide 28.CONNECT HEATER HOSE

a.

Connect the heater water outlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.


b.

Connect the heater water inlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.


Hide 16400 29.INSTALL RADIATOR ASSEMBLY

Hide 16711 30.INSTALL FAN SHROUD

Hide 16470 31.INSTALL RADIATOR RESERVOIR

Hide 16572 32.INSTALL RADIATOR HOSE OUTLET

Hide 16571 33.INSTALL RADIATOR HOSE INLET

Hide 16593 34.INSTALL NO. 1 RADIATOR AIR GUIDE

Hide 53294C 35.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 36.INSTALL RADIATOR SIDE DEFLECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 17861 37.INSTALL INTAKE AIR CONNECTOR

Hide 17701 38.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Attach the 3 wire harness clamps.


Hide 17801 39.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner cap sub-assembly.


Hide 17705 40.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

a.

Install the air cleaner cap sub-assembly with No. 1 air cleaner hose and tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Attach the 4 clamps.


c.

Connect the intake mass air flow meter connector and attach the 2 wire harness clamps.


Hide 53301 41.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose to the hood sub-assembly.


c.

Adjust the hood sub-assembly.

Click hereVehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT


Hide 42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 22030 53.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 51441 54.INSTALL NO. 1 ENGINE UNDER COVER (w/ Cover)

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 51410 55.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (w/ Cover)

Hide 53882F 56.INSTALL FRONT FENDER SEAL LH

a.

Install the front fender seal LH with the 5 new clips.


Hide 53882F 57.INSTALL FRONT FENDER SEAL RH

a.

Install the front fender seal RH with the 5 new clips.


Hide 53737B 58.INSTALL FRONT UPPER FENDER APRON SEAL LH

a.

Install the front upper fender apron seal LH with the 6 new clips.


Hide 53736 59.INSTALL FRONT UPPER FENDER APRON SEAL RH

a.

Install the front upper fender apron seal RH with the 6 new clips.