If 2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| Symptom | Trouble Area |
|---|---|
| 2 or more ECUs and/or sensors do not appear on the GTS "Bus Check" screen. | ·
Brake actuator assembly (skid control ECU)*1 ·
Master cylinder solenoid (skid control ECU)*2 ·
Four wheel drive control ECU ·
Certification ECU (smart key ECU assembly) ·
Power management control ECU ·
Power steering ECU assembly ·
Navigation receiver assembly*3 ·
Radio and display receiver assembly*4 ·
Spiral cable sub-assembly (steering angle sensor) ·
Yaw rate sensor assembly ·
Center airbag sensor assembly ·
Main body ECU (multiplex network body ECU) ·
Telematics transceiver*5 |
*1: for 2TR-FE
*2: for 1GR-FE, 1KD-FTV, 1GD-FTV
*3: w/ Navigation System (for Navigation Receiver Type)
*4: w/ Navigation System (for Radio and Display Type) or w/o Navigation System
*5: w/ Telematics Transceiver
Perform the following inspection for the ECUs (sensors) which are not displayed on the GTS. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.
Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.
The open circuit confirmation of the combination meter assembly, ECM and CAN main wire is performed in the Check CAN Bus Line procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.
Disconnect the A6 brake actuator assembly (skid control ECU)*1 or A7 master cylinder solenoid (skid control ECU)*2 connector.
*1: for 2TR-FE
*2: for 1GR-FE, 1KD-FTV, 1GD-FTV
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS (for 2TR-FE) | A |
| "Skid Control (ABS/VSC/TRAC)" is not displayed on the GTS (for 1GR-FE, 1KD-FTV, 1GD-FTV) | B |
| Several ECUs and sensors in addition to "Skid Control (ABS/VSC/TRAC)" are displayed on the GTS | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-25 (CANH) - A6-14 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
OK
NG
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A7-11 (CANH) - A7-25 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU]) |
OK
NG
Disconnect the G64 main body ECU (multiplex network body ECU) connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Main Body" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Main Body" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G64-14 (CANH) - G64-13 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU]) |
OK
NG
Disconnect the G1 center airbag sensor assembly connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Airbag" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Airbag" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G1-13 (CANH) - G1-22 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Center Airbag Sensor Assembly) |
OK
NG
Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Spiral cable (Steering Angle Sensor)" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Spiral cable (Steering Angle Sensor)" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G33-4 (CANH) - G33-3 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor]) |
OK
NG
Disconnect the G53 four wheel drive control ECU connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Four Wheel Drive Control" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Four Wheel Drive Control" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G53-19 (CANH) - G53-20 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Four Wheel Drive Control ECU) |
OK
NG
Disconnect the G38 certification ECU (smart key ECU assembly) connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Certification (Smart)" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Certification (Smart)" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G38-9 (CANH) - G38-10 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
OK
NG
Disconnect the G46 power steering ECU assembly connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "PPS" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "PPS" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G46-1 (CANH) - G46-2 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
OK
NG
Disconnect the G51 power management control ECU connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Power Management1" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Power Management1" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G51-14 (CA1H) - G51-13 (CA1L) | Engine switch off | 54 to 69 Ω |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
OK
NG
For vehicles without a telematics transceiver, go to "Check for Open in One Side of CAN Branch Wire (Yaw Rate Sensor Assembly)".
Disconnect the G187 telematics transceiver connector.
Select "Bus Check" on the GTS.
| Result | Proceed to |
|---|---|
| "DCM" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "DCM" are displayed on the GTS | B |
A
B
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G187-15 (CANP) - G187-16 (CANN) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Telematics Transceiver) |
OK
NG
Disconnect the G52 yaw rate sensor assembly connector.
Select "Bus Check" on the GTS (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| "Yaw Rate Sensor" is not displayed on the GTS | A |
| Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the GTS (w/ Navigation System [for Navigation Receiver Type]) | B |
| Several ECUs and sensors in addition to "Yaw Rate Sensor" are displayed on the GTS (w/ Navigation System [for Radio and Display Type] or w/o Navigation System) | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G52-3 (CANH) - G52-2 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Yaw Rate Sensor Assembly) |
OK
NG
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the H56 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H56-9 (CANH) - H56-10 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
OK
NG
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the H51 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H51-9 (CANH) - H51-10 (CANL) | Engine switch off | 54 to 69 Ω |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
OK
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
NG